MC3302P

NCV2901 ONSEMI | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 10

Technical content

Features

• Pb−Free Packages are Available*
• Single or Split Supply Operation
• Low Input Bias Current: 25 nA (Typ)
• Low Input Offset Current: ±5.0 nA (Typ)
• Low Input Offset V oltage
• Input Common Mode V oltage Range to GND
• Low Output Saturation V oltage: 130 mV (Typ) @ 4.0 mA
• TTL and CMOS Compatible
• ESD Clamps on the Inputs Increase Reliability without Affecting Device Operation *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. PDIP−14 N, P SUFFIX CASE 646 SOIC−14 D SUFFIX CASE 751A PIN CONNECTIONS Output 2 - Input 1 Output 1 Output 3 Output 4 + Input 1 - Input 2 + Input 2 + Input 4 - Input 4 + Input 3 - Input 3 V CC GND (Top View) See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet.

ORDERING INFORMATION

See general marking information in the device marking section on page 8 of this data sheet. DEVICE MARKING INFORMATION http://onsemi.com TSSOP−14 DTB SUFFIX CASE 948G

damage may occur and reliability may be affected.

1. The maximum output current may be as high as 20 mA, independent of the magnitude of VCC . Output short circuits to VCC can cause excessive

heating and eventual destruction. Figure 1. Circuit Schematic NOTE: Diagram shown is for 1 comparator.

LM339, LM239, LM2901, LM2901V, NCV2901, MC3302 http://onsemi.com ELECTRICAL CHARACTERISTICS (VCC = +5.0 Vdc, TA = +25°C, unless otherwise noted) LM239/339 LM2901/2901V/ NCV2901 MC3302 Characteristic Symbol Min Typ Max Min Typ Max Min Typ Max Unit Input Bias Current (Notes 3, 4) IIB − 25 250 − 25 250 − 25 500 nA (Output in Analog Range) Input Offset Current (Note 3) IIO − ±5.0 ±50 − ±5.0 ±50 − ±3.0 ±100 nA Input Common Mode Voltage Range VICMR 0 − VCC −1.5 0 − VCC −1.5 0 − VCC −1.5 V Supply Current ICC mA Voltage Gain AVOL 50 200 − 25 100 − 25 100 − V/mV R L ≥ 15 k, VCC = 15 Vdc Large Signal Response Time − − 300 − − 300 − − 300 − ns VI = TTL Logic Swing, Vref = 1.4 Vdc, VRL = 5.0 Vdc, R L = 5.1 k Response Time (Note 5) − − 1.3 − − 1.3 − − 1.3 − s VRL = 5.0 Vdc, RL = 5.1 k Output Sink Current ISink 6.0 16 − 6.0 16 − 6.0 16 − mA VO ≤ 1.5 Vdc Saturation Voltage Vsat − 130 400 − 130 400 − 130 500 mV VI(−) ≥ +1.0 Vdc, VI(+) = 0, Isink ≤ 4.0 mA Output Leakage Current IOL − 0.1 − − 0.1 − − 0.1 − nA VI(+) ≥ +1.0 Vdc, VI(−) = 0, VO = +5.0 Vdc 2. (LM239) Tlow = −25°C, Thigh = +85° (LM339) Tlow = 0°C, Thigh = +70°C (MC3302) Tlow = −40°C, Thigh = +85°C (LM2901) Tlow = −40°C, Thigh = +105° (LM2901V & NCV2901) Tlow = −40°C, Thigh = +125°C NCV2901 is qualified for automotive use. 3. At the output switch point, VO 1.4 Vdc, RS ≤ 100 5.0 Vdc ≤ VCC ≤ 30 Vdc, with the inputs over the full common mode range (0 Vdc to VCC −1.5 Vdc). 4. The bias current flows out of the inputs due to the PNP input stage. This current is virtually constant, independent of the output state. 5. The response time specified is for a 100 mV input step with 5.0 mV overdrive. For larger signals, 300 ns is typical.

LM339, LM239, LM2901, LM2901V, NCV2901, MC3302 http://onsemi.com Device Package Shipping† LM239D SOIC−14 55 Units/Rail LM239DG SOIC−14 (Pb−Free)

55 Units/Rail

LM239DR2 SOIC−14 2500 Units/Tape & Reel LM239DR2G SOIC−14 (Pb−Free)

2500 Units/Tape & Reel

LM239DTBR2 TSSOP−14 (Pb−Free) LM239N PDIP−14 25 Units/Rail LM239NG PDIP−14 (Pb−Free)

25 Units/Rail

LM339D SOIC−14 55 Units/Rail LM339DG SOIC−14 (Pb−Free) LM339DR2 SOIC−14 2500 Units/Tape & Reel LM339DR2G SOIC−14 (Pb−Free) LM339DTBR2 TSSOP−14 (Pb−Free) LM339N PDIP−14 25 Units/Rail LM339NG PDIP−14 (Pb−Free) LM2901D SOIC−14 55 Units/Rail LM2901DR2 SOIC−14 2500 Units/Tape & Reel LM2901DR2G SOIC−14 (Pb−Free) LM2901DTBR2 TSSOP−14 (Pb−Free) LM2901N PDIP−14 25 Units/Rail LM2901NG PDIP−14 (Pb−Free) LM2901VD SOIC−14 55 Units/Rail LM2901VDG SOIC−14 (Pb−Free) LM2901VDR2 SOIC−14 2500 Units/Tape & Reel LM2901VDR2G SOIC−14 (Pb−Free) LM2901VDTBR2 TSSOP−14 (Pb−Free) LM2901VN PDIP−14 25 Units/Rail NCV2901DR2 SOIC−14 2500 Units/Tape & Reel NCV2901DR2G SOIC−14 (Pb−Free) MC3302D SOIC−14 55 Units/Rail MC3302DR2 SOIC−14 2500 Units/Tape & Reel MC3302DTBR2 TSSOP−14 (Pb−Free) MC3302P PDIP−14 25 Units/Rail †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.

LM339, LM239, LM2901, LM2901V, NCV2901, MC3302 http://onsemi.com A = Assembly Location WL, L = Wafer Lot YY, Y = Year WW, W = Work Week SOIC−14 D SUFFIX CASE 751A PDIP−14 N, P SUFFIX CASE 646 LM339N AWLYYWW MARKING DIAGRAMS LM239N AWLYYWW LM2901N AWLYYWW LM2901VN AWLYYWW MC3302P AWLYYWW LM339D AWLYWW LM239D AWLYWW LM2901D AWLYWW LM2901VD AWLYWW MC3302D AWLYWW *This marking diagram also applies to NCV2901. 239 ALYW TSSOP−14 DTB SUFFIX CASE 948G 339 ALYW 2901 ALYW 2901 V ALYW 3302 ALYW

LM339, LM239, LM2901, LM2901V, NCV2901, MC3302 http://onsemi.com PACKAGE DIMENSIONS PDIP−14 P SUFFIX CASE 646−06 ISSUE M 14 8 B A DIM MIN MAX MIN MAX MILLIMETERSINCHES A 0.715 0.770 18.16 18.80 B 0.240 0.260 6.10 6.60 C 0.145 0.185 3.69 4.69 D 0.015 0.021 0.38 0.53 F 0.040 0.070 1.02 1.78 G 0.100 BSC 2.54 BSC H 0.052 0.095 1.32 2.41 J 0.008 0.015 0.20 0.38 K 0.115 0.135 2.92 3.43 L M --- 10 --- 10 N 0.015 0.039 0.38 1.01 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL.F HG D K C SEATING PLANE N −T− 14 PL M0.13 (0.005) L M J 0.290 0.310 7.37 7.87 SOIC−14 D SUFFIX CASE 751A−03 ISSUE G NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. −A− −B− G P 7 PL 14 8 M0.25 (0.010) B M SBM0.25 (0.010) A ST −T− FR X 45 SEATING PLANE D 14 PL K C JM DIM MIN MAX MIN MAX INCHESMILLIMETERS A 8.55 8.75 0.337 0.344 B 3.80 4.00 0.150 0.157 C 1.35 1.75 0.054 0.068 D 0.35 0.49 0.014 0.019 F 0.40 1.25 0.016 0.049 G 1.27 BSC 0.050 BSC J 0.19 0.25 0.008 0.009 K 0.10 0.25 0.004 0.009 M 0 7 0 7 P 5.80 6.20 0.228 0.244 R 0.25 0.50 0.010 0.019

LM339, LM239, LM2901, LM2901V, NCV2901, MC3302 http://onsemi.com PACKAGE DIMENSIONS TSSOP−14 DTB SUFFIX CASE 948G−01 ISSUE O DIM MIN MAX MIN MAX INCHESMILLIMETERS A 4.90 5.10 0.193 0.200 B 4.30 4.50 0.169 0.177 D 0.05 0.15 0.002 0.006 F 0.50 0.75 0.020 0.030 G 0.65 BSC 0.026 BSC H 0.50 0.60 0.020 0.024 J 0.09 0.20 0.004 0.008 J1 0.09 0.16 0.004 0.006 K 0.19 0.30 0.007 0.012 K1 0.19 0.25 0.007 0.010 L 6.40 BSC 0.252 BSC M 0 8 0 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. SU0.15 (0.006) T 2X L/2 SUM0.10 (0.004) V ST L −U− SEATING PLANE 0.10 (0.004) −T− ÇÇÇ ÇÇÇ ÇÇÇ SECTION N−N DETAIL E J J1 K ÉÉ ÉÉ DETAIL E F M −W− 0.25 (0.010) 814 PIN 1 IDENT. HG A D C B SU0.15 (0.006) T −V− 14X REFK N N ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION N. American Technical Support: 800−282−9855 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Phone : 81−3−5773−3850 LM339/D LITERATURE FULFILLMENT : Literature Distribution Center for ON Semiconductor P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Phone : 480−829−7710 or 800−344−3860 Toll Free USA/Canada Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative.