MB507 FUJITSU | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

Sept. 1995 Edition 4.0a Copyright 1995 by FUJITSU LIMITED and FUJITSU MICROELECTRONICS MB507 1.6GHz TWO MODULUS PRESCALER 1.6GHz TWO MODULUS PRESCALER The Fujitsu MB507 is a 1.6GHz two modulus prescaler used with a frequency synthesizer to form a Phase Locked Loop (PLL). It will divide the input frequency by the modulus of 128/129 or 256/257 and has an output level of 1.6V peak to peak on ECL level.

FEATURES

High Frequency Operation 1.6GHz max. Power Dissipation 90mW typ. Pulse Swallow Function Wide Operation Temperature -40°C to +85°C Stable Output Amplitude V OUT = 1.6Vp–p Complete PLL synthesizer circuit with the Fujitsu MB87001A, PLL synthesizer IC Package Standard 8-pin Dual-In-Line Package (Suffix: –P) Standard 8-pin Flat Package (Suffix: –PF) ABSOLUTE MAXIMUM RATINGS (See Note) Rating Symbol Value Unit Supply Voltage VCC –0.5 to +7.0 V Input Voltage VIN –0.5 to VCC V Output Current IO 10 mA Storage Temperature TSTG –55 to +125 °C Note: Permanent device damage may occur if the above Absolute Maximum Ratings are exceeded. Functional operation should be restricted to the conditions as detailed in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. PLASTIC PACKAGE FPT-08P-M01 PIN ASSIGNMENT This device contains circuitry to protect the inputs against damage due to high static voltages or electric fields. However, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum rated voltages to this high impedance circuit. PLASTIC PACKAGE DIP-08P-M01 IN VCC SW OUT IN NC GND MC TOP VIEW

Figure 1. MB507 Block Diagram

1 IN Input

2 VCC DC Supply Voltage

3 SW Divide Ratio Control Input Selecting Divide Ratio (See Divide Ratio Table)

4 OUT Output

5 GND Ground

6 MC Modulus Control Input (See Divide Ratio Table)

7 NC No Connection

8 IN Complementary Input

RECOMMENDED OPERATING CONDITIONS Parameter Symbol Value UnitParameter Symbol Min. Typ. Max. Unit Supply Voltage VCC 4.5 5.0 5.5 V Output Current IO 1.2 mA Ambient Temperature TA –40 +85 °C Load Capacitance C L 12 pF

ELECTRICAL CHARACTERISTICS

(Recommended Operating Conditions unless otherwise noted.) Parameter Symbol Conditions Value UnitParameter Symbol Conditions Min. Typ. Max. Unit Supply Curent ICC 18 mA Output Amplitude VO 1.0 1.6 Vp–p Input Frequency fIN with input coupling capacitor 1000pF 100 1600 MHz Input Signal Amplitude PIN –4 10 dBm High Level Input Voltage for MC Input VIHM 2.0 V Low Level Input Voltage for MC Input VILM V High Level Input Voltage for SW Input VIHS* VCC –0.1 VCC VCC +0.1 V Low Level Input Voltage for SW Input VILS Open V High Level Input Current for MC Input IIHM VIH = 2.0V 0.4 mA Low Level Input Current for MC Input IILM VIL = 0.8V –0.2 mA Modulus Set-up Time MC to OUT tSET 1.6GHz Operation 18 28 ns Note: *Design Guarantee

Figure 2. Test Circuit Note:When divide of 129 is selected, positive pulse is applied by one to 65. The typical set up time is 18 ns from the MC signal input to the timing of change of prescaler divide ratio.

(Suffix: P) 8-LEAD PLASTIC DUAL IN-LINE PACKAGE (CASE No: DIP-08P-M01) .370 .016 – .012 9.40 0.40 – 0.30 .244+.010 (6.20+0.25) INDEX .039 .012 – 0 0.99 0.30 – 0 .060 .012 – 0 1.52 0.30 – 0 .035 .014 – .012 0.89 0.35 – 0.30 .172(4.36) MAX MIN .100(2.54) TYP .018+.003 (0.46+0.08) .300(7.62) TYP .010+.002 (0.25+0.05) 15° MAX DImensions in inches (millimeters) 1988 FUJITSU LIMITED D08006S-2C

(Suffix: PF) 8-LEAD PLASTIC FLAT PACKAGE (CASE No: FPT-08P-M01) DImensions in inches (millimeters) 1988 FUJITSU LIMITED F08002S-3C INDEX .250 .010 – .008 6.35 0.25 – 0.20 .307+.016 (7.80+0.40) .209+.012 (5.30+0.30) .050(1.27) TYP .150(3.81) REF .018+.004 “A” .004(0.10) Details of “A” part .008(0.20) .020(0.50) .007(0.18) MAX .027(0.68) MAX .006 .002 – .001 0.15 0.05 – 0.02 .020+.008 (0.50+0.20) .268 .016 – .008 6.80 0.40 – 0.20 .089(2.25) MAX (SEATED HEIGHT) .002(0.05) MIN (STAND OFF) All Rights Reserved. Circuit diagrams utilizing Fujitsu products are included as a means of illustrating typical semiconductor applications. Complete information sufficient for construction purposes is not necessarily given. The information contained in this document has been carefully checked and is believed to be reliable. However, Fujitsu assumes no responsibility for inaccuracies. The information contained in this document does not convey any license under the copy- rights, patent rights or trademarks claimed and owned by Fujitsu. Fujitsu reserves the right to change products or specifications without notice. No part of this publication may be copied or reproduced in any form or by any means, or transferred to any third party without prior written consent of Fujitsu.

For further information please contact: Japan FUJITSU LIMITED International Marketing Div. Furukawa Sogo Bldg., 6-1, Marunouchi 2-chome Chiyoda-ku, Tokyo 100, Japan Tel: (03) 3216-3211 Telex: 781-2224361 FAX: (03) 3215-0662 North and South America FUJITSU MICROELECTRONICS, INC. Integrated Circuits Division

3545 North First Street

San Jose, CA 95134-1804, USA Tel: 408-922-9000 FAX: 408-432-9044 Europe FUJITSU MIKROELEKTRONIK GmbH Am Siebenstein 6-10,

6072 Dreieich-Buchschlag,

Tel: (06103) 690-0 Telex: 411963 FAX: (06103) 690-122 Asia FUJITSU MICROELECTRONICS ASIA PTE LIMITED

51 Bras Basah Road,

Plaza By The Park, #06-04 to #06-07 Singapore 0719 Tel: 336-1600 Telex: 55573 FAX: 336-1609  FUJITSU LIMITED 1990 Printed in Japan PV0026–904A4