MB506 FUJITSU | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Sept. 1995 Edition 3.0a Copyright 1995 by FUJITSU LIMITED and FUJITSU MICROELECTRONICS MB506 ULTRA HIGH FREQUENCY PRESCALER ULTRA HIGH FREQUENCY PRESCALER The Fujitsu MB506 is a high frequency, up to 2.4GHz, prescaler used with a frequency synthesizer to form a Phase Locked Loop (PLL). It will divide the input frequency by the modulus of 128 or 256 and the output level is 1.6V peak to peak on ECL level.Operation in the 1.6GHz range meets the specification for applications in Direct Broadcasting Satellite Systems (DBS), CATV systems, and UHF Transceivers.
FEATURES
High Frequency Operation 2.4GHz max. Power Dissipation 90mW typ. Wide Operation Temperature -40°C to +85°C Stable Output Amplitude V OUT = 1.6Vp–p Complete PLL synthesizer circuit with the Fujitsu MB87006A, PLL synthesizer IC Plastic 8-pin Standard Dual-In-Line Package or Flat Package ABSOLUTE MAXIMUM RATINGS (See Note) Rating Symbol Value Unit Supply Voltage VCC –0.5 to +7.0 V Input Voltage VIN –0.5 to VCC V Output Current IO 10 mA Storage Temperature TSTG –55 to +125 °C Note: Permanent device damage may occur if the above Absolute Maximum Ratings are exceeded. Functional operation should be restricted to the conditions as detailed in PLASTIC PACKAGE FPT-08P-M01 PIN ASSIGNMENT This device contains circuitry to protect the inputs against damage due to high static voltages or electric fields. However, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum rated voltages to this high impedance circuit. PLASTIC PACKAGE DIP-08P-M01 IN VCC SW OUT IN NC GND SW2 TOP VIEW
conditions for extended periods may affect device reliability. Figure 1. MB506 Block Diagram
1 IN Input
2 VCC Power Supply Voltage
3 SW1 Divide Ratio Control Input Selecting Divide Ratio (See Divide Ratio Table)
4 OUT Output
5 GND Ground
6 SW2 Divide Ratio Control Input Selecting Divide Ratio (See Divide Ratio Table)
7 NC No Connection
8 IN Complementary Input
RECOMMENDED OPERATING CONDITIONS Parameter Symbol Value UnitParameter Symbol Min. Typ. Max. Unit Supply Voltage VCC 4.5 5.0 5.5 V Output Current IO 1.2 mA Ambient Temperature TA –40 +85 °C Load Capacitance C L 12 pF
ELECTRICAL CHARACTERISTICS
(Recommended operating conditions unless otherwise noted.) Parameter Symbol Conditions Value UnitParameter Symbol Conditions Min. Typ. Max. Unit Supply Curent ICC 18 mA Output Amplitude VO 1.0 1.6 Vp–p Input Frequency fIN with input coupling TA = –40°C to 85°C 100 2200 MHzInput Frequency fIN coupling capacitor 1000pF TA = –40°C to 60°C 100 2400 MHz Input Signal Amplitude PIN fIN = 100MHz to 1.3GHz –16 5.5 dBmInput Signal Amplitude PIN fIN = 1.3MHz to 2.4GHz –4 5.5 dBm High Level Input Voltage for SWVIHS* VCC –0.1 VCC VCC +0.1 V Low Level Input Voltage for SWVILS Open V Note: *Design Guarantee MINIMUM INPUT SIGNAL AMPLITUDE (MVp–p) INPUT FREQUENCY (MHz) 1000 800 600 400 200 100 200 500 1000 2000 5000 VCC = 5.0V TA = 25°C Figure 2. Input Signal Amplitude vs. Input Frequency
.018+.004 (0.45+0.10) INDEX .244+.010 (6.20+0.25) .010+.02 (0.25+0.5).370 .016 – .012 9.40 0.40 – 0.30 .035 .014 – .012 0.89 0.35 – 0.30 .300(7.62)TYP 15° MAX .100(2.54)TYP .172(4.36)MAX MIN .018+.003 (0.46+0.08) .039 .012 – 0 0.99 0.3 – 0 .060 .012 – 0 1.52 0.3 – 0 8-LEAD PLASTIC DUAL-IN-LINE PACKAGE (CASE No.: DIP-08P-M01) 8-LEAD PLASTIC FLAT PACKAGE (CASE No.: FPT-08P-M01) .250 .010 – .008 6.35 0.25 – 0.20 INDEX .307+.016 (7.8+0.4) .209+.012 (5.30+0.25) .050(1.27) TYP .085(2.15)MAX .0315+.008 (0.8+0.2) .006 .002 – .001 0.15 0.05 – 0.2 .002(0.05) MIN (STAND OFF) .268 .016 – .008 6.80 0.40 – 0.20 .020+.008 (0.5+0.2) View “A” .008(0.2) .020(0.5) .007(0.18) MAX .027(0.68) MAX A
1987 FUJITSU LIMITED D08006S-2C 1987 FUJITSU LIMITED F08002S-2C
inches (millimeters) Dimensions in inches (millimeters) All Rights Reserved. Circuit diagrams utilizing Fujitsu products are included as a means of illustrating typical semiconductor applications. Complete information sufficient for construction purposes is not necessarily given. The information contained in this document has been carefully checked and is believed to be reliable. However, Fujitsu assumes no responsibility for inaccuracies. The information contained in this document does not convey any license under the copyrights, patent rights or trademarks claimed and owned by Fujitsu. Fujitsu reserves the right to change products or specifications without notice. No part of this publication may be copied or reproduced in any form or by any means, or transferred to any third party without prior written consent of Fujitsu. FUJITSU LIMITED For further information please contact: Japan FUJITSU LIMITED International Marketing Div. Furukawa Sogo Bldg., 6-1, Marunouchi 2-chome Chiyoda-ku, Tokyo 100, Japan Tel: (03) 3216-3211 Telex: 781-2224361 FAX: (03) 3215-0662 North and South America FUJITSU MICROELECTRONICS, INC. Integrated Circuits Division
3545 North First Street
San Jose, CA 95134-1804, USA Tel: 408-922-9000 FAX: 408-432-9044 Europe FUJITSU MIKROELEKTRONIK GmbH Am Siebenstein 6-10,
6072 Dreieich-Buchschlag,
Tel: (06103) 690-0 Telex: 411963 FAX: (06103) 690-122 Asia FUJITSU MICROELECTRONICS ASIA PTE LIMITED
51 Bras Basah Road,
Plaza By The Park, #06-04 to #06-07 Singapore 0719 Tel: 336-1600 Telex: 55573 FAX: 336-1609 FUJITSU LIMITED 1990 Printed in Japan PV0050–902A3