MAX40002

MAX40002–MAX40005 MAX40012–MAX40015 - nanoPower 4-Bump Comparator in Ultra-Tiny 0.73mm x 0.73mm WLP/SOT23 Packages

Document overview

• PDF pages: 16

Technical content

The MAX40002–MAX40005 and MAX40012–MAX40015 tiny, single comparators are ideal for a wide variety of portable electronics applications such as cell phones, media players, and notebooks that have extremely tight board space and power constraints. These comparators are offered in both, a miniature 4-bump wafer-level pack - age (WLP) with a 0.73mm x 0.73mm footprint (as small as two 0402 resistors) and a 5-pin SOT23 package. This device family operates with a supply voltage range from 1.7V to 5.5V (either V CC or external V REF), and consumes only 500nA of supply current. These devices have a wide input-voltage range of 0.1V to 5.5V, independent of the supply voltage, and maintain high impedance at the inputs even when powered down (V CC or external VREF = 0V). They also feature internal filtering to provide high RF immunity. The MAX40002–MAX40003 and MAX40012–MAX40013 have open-drain outputs, while the MAX40004–MAX40005 and MAX40014–MAX40015 feature push-pull outputs. The MAX40002/MAX40004 and MAX40012–MAX40014 have noninverting inputs, while the MAX40003/MAX40005 and MAX40013–MAX40015 have inverting inputs (see the Selector Guide for more information). These devices also come with an internal reference. The reference voltage is preset at the factory and parts are offered with the following voltage options: 0.2V, 0.5V, 0.9V or 1.222V (see Ordering Information table). These devices are fully specified over -40°C to +125°C automotive temperature range.

Applications

• Mobile Devices
• Portable Medical Devices
• Portable Instrumentation
• Notebook Computers
• Electronic Toys Benefits and Features
• Tiny 0.73mm x 0.73mm, 4-Bump WLP and 5-Pin SOT23 Packages Save Board Space
• Ultra-Low 500nA Operating Current Preserves Battery Power in Applications Where Comparator is Constantly Monitoring
• 1.7V to 5.5V Supply Range Allows Operation from 1.8V, 2.5V, 3V and 5V Systems
• Input Voltage Range: 0.1V to 5.5V
• External REF Range: 1.7V to 5.5V
• Wide Variety of Factory-Trimmed Reference Voltages Saves Space and Cost of External Reference:
• 9µs Propagation Delay
• -40°C to +125°C Specified Temperature Range Ordering Information appears at end of data sheet. 19-8574; Rev 9; 4/22 Click here to ask an associate for production status of specific part numbers. nanoPower 4-Bump Comparator in Ultra-Tiny 0.73mm x 0.73mm WLP/SOT23 Packages MAX40002–MAX40005 MAX40012–MAX40015 Evaluation Kit Available Design Resources Tools and Models Support © 2022 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.

Junction-to-Ambient Thermal Resistance (θJA) ...104.41°C/W SOT23 (Note 1) Continuous Power Dissipation (TA = +70°C) VCC/REF = 3.3V, RPULLUP = 100kΩ to V PULLUP = 3.3V, RL = ∞, C L = 20pF, TA = TMIN to TMAX. Typical values are at T A = +25°C, unless otherwise noted. (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS POWER SUPPLY VOLTAGE VCC/REF Supply Voltage Range VCC/VREF 1.7 5.5 V VCC/REF Supply Current ICC VIN > 0, VOUT = low, no output or reference load current, TA = -40°C to +85°C 0.5 1.1 µA VIN > 0, VOUT = low, no output or reference load current, TA = -40°C to +125°C 1.3 Power-Up Time 0.5 ms COMPARATOR Input Voltage Range VIN TA = +25°C 0.1 VCC + 0.1 V TA = -40°C to +125°C 0.1 VCC Input Offset Voltage (For External VREF only) (Note 3) VOS Over VIN range, TA = -40°C to +85°C 0.5 27 mV Over VIN range, TA = -40°C to +125°C 32 Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial. Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Package Thermal Characteristics

Electrical Characteristics

www.analog.com Analog Devices │ 2 MAX40002–MAX40005 MAX40012–MAX40015 nanoPower 4-Bump Comparator in Ultra-Tiny 0.73mm x 0.73mm WLP/SOT23 Packages

VCC/REF = 3.3V, RPULLUP = 100kΩ to V PULLUP = 3.3V, RL = ∞, C L = 20pF, TA = TMIN to TMAX. Typical values are at T A = +25°C, unless otherwise noted. (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Input Offset Drift (For External VREF Only) (Note 3) 320 µV/°C Input Hysteresis VHYS (Note 4) 8 mV Input Bias Current Over VIN range, TA = -40°C to +85°C 20 30 nA Over VIN range, TA = -40°C to +125°C 90 Input Leakage Current (VCC/REF = 0) (MAX40002 and MAX40003) No supply voltage, TA = -40°C to +85°C 20 30 nA No supply voltage, TA = -40°C to +125°C 80 Input Capacitance Either input, over VCM range 0.4 pF Power Supply Rejection Ratio PSRR DC, internal VREF 40 dB DC, external VREF 45 Output Voltage Swing Low VOL Sinking 2mA, measured relative with GND 0.4 V Output Voltage Swing High VOH Sourcing 1mA, measured with relative with VCC 0.4 V Output Leakage Current IO-LKG Open-drain only, VCC/REF = 1.8V, VO = 5.5V, TA = -40°C to +125°C 100 nA Propagation Delay (Note 5) tPD 100mV overdrive, push-pull OUT = low to high 25 µs 100mV overdrive, open-drain, RPU = 100kΩ, OUT = low to high 25 100mV overdrive, both push-pull and open-drain, OUT= high to low 9 20mV overdrive, push-pull OUT = low to high 50 20mV overdrive, open-drain, RPU = 100kΩ, OUT = low to high 55 20mV overdrive, both push-pull and open-drain, OUT = high to low 45 Rise Time tR Push-pull output 800 ns Fall Time tF 200 ns Electrical Characteristics (continued) www.analog.com Analog Devices │ 3 MAX40002–MAX40005 MAX40012–MAX40015 nanoPower 4-Bump Comparator in Ultra-Tiny 0.73mm x 0.73mm WLP/SOT23 Packages

VCC/REF = 3.3V, RPULLUP = 100kΩ to V PULLUP = 3.3V, RL = ∞, C L = 20pF, TA = TMIN to TMAX. Typical values are at T A = +25°C, unless otherwise noted. (Note 2) Note 2: All devices are 100% production tested at T A = +25°C. Temperature limits are guaranteed by design. Note 3: VOS is the average of the positive and negative trip points minus V REF. Note 4: Hysteresis is the input voltage difference between the two switching points. Note 5: Overdrive (VOD) is the voltage above or below the switching points. The input starts at 100mV below the trip point and use 50% input to 50% output for timing. V IN = VREF_INT±VOD±VHYS. Note 6: Switching Threshold Voltages include the offset voltage of the comparator and the internal reference. PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS INTERNAL REFERENCE VOLTAGE Switching Threshold Voltage (Note 6) VREF-INT TA = +25°C MAX4000_ _ _ _02+ 188 200 212 mV TA = -40°C to +85°C MAX4000_ _ _ _02+ 177 223 mV TA = -40°C to +125°C MAX4000_ _ _ _02+ 174 226 mV TA = +25°C MAX4000_ _ _ _05+ 485 500 515 mV TA = -40°C to +85°C MAX4000_ _ _ _05+ 468 532 mV TA = -40°C to +125°C MAX4000_ _ _ _05+ 463 537 mV TA = +25°C MAX4001_ _ _ _ 09+ 882 900 918 mV TA = -40°C to +85°C MAX4001_ _ _ _ 09+ 873 927 mV TA = -40°C to +125°C MAX4001_ _ _ _ 09+ (WLP) 873 927 mV MAX4001_ _ _ _ 09+ (SOT23) 864 936 TA =+25°C MAX4000_ _ _ _ 12+ 1200 1222 1244 mV TA = -40°C to +85°C MAX4000_ _ _ _ 12+ 1169 1275 mV TA = -40°C to +125°C MAX4000_ _ _ _ 12+ 1157 1287 mV Electrical Characteristics (continued) www.analog.com Analog Devices │ 4 MAX40002–MAX40005 MAX40012–MAX40015 nanoPower 4-Bump Comparator in Ultra-Tiny 0.73mm x 0.73mm WLP/SOT23 Packages

VCC/REF = 3.3V, VGND = 0V, TA =25°C, unless otherwise noted. Typical Operating Characteristics 0.2 0.4 0.6 0.8 1.2 SUPPLY CURRENT (μA) SUPPLY VOLTAGE (V) SUPPLY CURRENT vs. SUPPLY VOLTAGE toc01 VOUT = LOW TA = -40°CTA = +25°C TA = +85°C TA = +125°C 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 0 20 40 60 80 OUTPUT VOLTAGE LOW (V) SINK CURRENT (mA) OUTPUT VOLTAGE LOW vs. SINK CURRENT (TA = -40°C) toc3a VCC = 5V VCC = 1.8V VCC = 3.3V 0.2 0.4 0.6 0.8 1.2 0 20 40 60 OUTPUT VOLTAGE LOW (V) SINK CURRENT (mA) OUTPUT VOLTAGE LOW vs. SINK CURRENT(TA = +125°C) toc3c VCC = 5V VCC = 1.8V VCC = 3.3V 0.1 1 10 100 SUPPLY CURRENT (μA) OUTPUT TRANSISTION FREQUENCY (kHz) VCC = 1.8V SUPPLY CURRENT vs. OUTPUT TRANSITION FREQUENCY toc02 VCC = 3.3V VCC = 5V VREF-INT = 0.2V 0.2 0.4 0.6 0.8 1.2 0 20 40 60 80 OUTPUT VOLTAGE LOW (V) SINK CURRENT (mA) OUTPUT VOLTAGE LOW vs. SINK CURRENT (TA = +25°C) toc3b VCC = 5V VCC = 1.8V VCC = 3.3V 0.5 1.5 2.5 0 20 40 60 80 OUTPUT VOLTAGE HIGH(VCC - VOH,V) SOURCE CURRENT (mA) OUTPUT VOLTAGE HIGH vs. SOURCE CURRENT(TA = -40°C) toc4a VCC = 5V VCC = 1.8V VCC = 3.3V Analog Devices │ 5www.analog.com MAX40002–MAX40005 MAX40012–MAX40015 nanoPower 4-Bump Comparator in Ultra-Tiny 0.73mm x 0.73mm WLP/SOT23 Packages

VCC/REF = 3.3V, VGND = 0V, TA =25°C, unless otherwise noted. Typical Operating Characteristics (continued) 0.5 1.5 2.5 0 20 40 60 OUTPUT VOLTAGE HIGH (VCC - VOH,V) SOURCE CURRENT (mA) OUTPUT VOLTAGE HIGH vs. SOURCE CURRENT(TA = +25°C) toc4b VCC = 5V VCC = 1.8V VCC = 3.3V 0.5 1.5 INPUT BIAS CURRENT (nA) INPUT BIAS VOLTAGE (V) INPUT BIAS CURRENT vs. INPUT BIAS VOLTAGE toc05 VREF-INT = 0.2V 100 120 140 160 0 20 40 60 80 100 120 140 160 180 200 PROPAGATION DELAY (μs) INPUT OVERDRIVE (mV) PROPAGATION DELAY vs. INPUT OVERDRIVE toc07 VREF-INT = 0.2V VCC = 1.8V VCC = 3.3V VCC = 5.0V 0.5 1.5 2.5 0 10 20 30 40 50 OUTPUT VOLTAGE HIGH(VCC - VOH,V) SOURCE CURRENT (mA) OUTPUT VOLTAGE HIGH vs. SOURCE CURRENT (TA = +125°C) toc4c VCC = 5V VCC = 1.8V VCC = 3.3V -50 -25 0 25 50 75 100 125 PROPAGATION DELAY (μs) TEMPERATURE (°C) PROPAGATION DELAY vs. TEMPERATURE toc06 VREF-INT = 0.2V VOD = ±100mV VCC = 1.8V VCC = 3.3V VCC = 5.0V PROPAGATION DELAY (μs) SUPPLY VOLTAGE (V) PROPAGATION DELAY vs. SUPPLY VOLTAGE toc08 VREF-INT = 0.2V VOD = ±200mV Analog Devices │ 6www.analog.com MAX40002–MAX40005 MAX40012–MAX40015 nanoPower 4-Bump Comparator in Ultra-Tiny 0.73mm x 0.73mm WLP/SOT23 Packages

VCC/REF = 3.3V, VGND = 0V, TA =25°C, unless otherwise noted. Typical Operating Characteristics (continued) OUTPUT RESPONSE LOW TO HIGH (VREF-INT = 0.2V, CLOAD = 20pF) 10μs/div (2V/div) VOUT VIN (100mV/div) toc09 1kHz FREQUENCY RESPONSE (VREF- INT = 0.2V, CLOAD = 20pF) 200μs/div (2V/div) VOUT VIN (100mV/div) toc11 POWER-UP/POWER-DOWN RESPONSE (VIN = 300mV) 1ms/div (2V/div) VOUT (2V/div) toc13 VCC 3.3V OUTPUT RESPONSE HIGH TO LOW (VREF-INT = 0.2V, CLOAD = 20pF) 4μs/div (2V/div) VOUT VIN (100mV/div) toc10 OUTPUT RESPONSE TO SUPPLY VOLTAGE TRANSIENT 1ms/div (2V/div) VOUT (200mV/div) toc12 VCC 3.2V (2V/div) VOUT (2V/div) VOUT VIN = VTH + 1mV VIN = VTH + 10mV VIN = VTH + 20mV 190 192 194 196 198 200 202 204 206 208 210 10 100 1000 10000 100000 1000000 TRIP POINT (mV) FREQUENCY (Hz) POWER-SUPPLY REJECTION FOR NO FALSE TRIGGERING toc14 VREF-INT = 0.2V VCC = 3.3V ±100mV LOWER TRIP POINT UPPER TRIP POINT Analog Devices │ 7www.analog.com MAX40002–MAX40005 MAX40012–MAX40015 nanoPower 4-Bump Comparator in Ultra-Tiny 0.73mm x 0.73mm WLP/SOT23 Packages

Comparator Output. OUT is an Open-Drain Output (MAX40002/MAX40003 and MAX40012/ MAX40013) or Push-Pull Output (MAX40004/MAX40005 and MAX40014/MAX40015). For the open-drain versions, connect a pullup resistor from OUT to any pullup voltage up to 5.5V for proper operation. A2 4 IN Comparator Input. The MAX40002/MAX40004 and MAX40012/MAX40014 have a noninverting input. The MAX40003/MAX40005 and MAX40013/MAX40015 have an inverting input (see Input Stage Circuitry for more information). B1 1 VCC/REF VCC Supply Voltage/External REF Voltage Input. VCC/REF is the supply voltage for devices with internal voltage reference (0.2V, 0.5V, 0.9V, 1.2V internal references. VCC/REF is the external reference input as well as the supply voltage for devices without the internal reference. Bypass VCC/REF with a 0.1µF capacitor to GND as close to the device pin as possible. B2 2 GND Ground. — 3 N.C. No Connect. Not internally connected. Pin Description Pin Configurations A B 1 2 TOP VIEW WLP OUT GND IN VCC/ REF MAX40002– MAX40005 AND MAX40012– MAX40015 SOT-23 OUT GND 1VCC/ REF 3 IN N. C. 4 MAX40002–MAX40005 AND MAX40012–MAX40015 www.analog.com Analog Devices │ 8 MAX40002–MAX40005 MAX40012–MAX40015 nanoPower 4-Bump Comparator in Ultra-Tiny 0.73mm x 0.73mm WLP/SOT23 Packages

current and low-voltage applications. the input voltage is greater than the voltage reference. al volts (limited only by Absolute Maximum Ratings). limiting this maximum overvoltage to about 0.3V. easily implemented in advanced battery-operated devices. programmed to include these pullup sources. of an internal Break-Before-Make design implementation. comparator is not externally accessible. Figure 1. Adaptive Signal-Level Detector

Table 1. How Devices Behave Under Various Input Voltage Conditions

Typical Operating Circuits IN MI CRO CONTROLLER OUT REF MAX40004ANS_ _ MAX40004AUK_ _ MAX40014ANS_ _ MAX40014AUK_ _ VCC = 1.7V TO 5.5V I/O VDD IN MI CRO CONTROLLER OUT REF MAX40005ANS_ _ MAX40005AUK_ _ MAX40015ANS_ _ MAX40015AUK_ _ VCC = 1.7V TO 5.5V I/O VDD IN MI CRO CONTROLLER OUT REF MAX40002ANS_ _ MAX40002AUK_ _ MAX40012ANS_ _ MAX40012AUK_ _ VCC = 1.7V TO 5.5V VDD I/O INTERNAL PULL-UP IN MI CRO CONTROLLER OUT REF MAX40003ANS_ _ MAX40003AUK_ _ MAX40013ANS_ _ MAX40013AUK_ _ VCC = 1.7V TO 5.5V VDD I/O INTERNAL PULL-UP IN REF OUT MAX40004ANS MAX40004AUK MAX40014ANS MAX40014AUK MI CRO CONTROLLER VDD I/O 1.7V TO 5.5V IN REF OUT MAX40005ANS MAX40005AUK MAX40015ANS MAX40015AUK MI CRO CONTROLLER VDD I/O 1.7V TO 5.5V IN REF OUT MAX40002ANS MAX40002AUK MAX40012ANS MAX40012AUK MI CRO CONTROLLER 1.7V TO 5.5V VDD I/O INTERNAL PULL-UP IN REF OUT MAX40003ANS MAX40003AUK MAX40013ANS MAX40013AUK MI CRO CONTROLLER 1.7V TO 5.5V VDD I/O INTERNAL PULL-UP MAX40002–MAX40003 AND MAX40012 –MAX40013 HAVE OPEN -DRAIN OUTPUT, MAX40004–MAX40005 AND MAX40014 –MAX40015 HAVE PUSHPULL OUTPUT, MAX40002/MAX40004 AND MAX40012/MAX40014 HAVE NONINVERTING INPUT, MAX40003/MAX40005 AND MAX40013/MAX40015 HAVE INVERTING INPUT, THE “_ _” INDICATES INTERNAL REFERENCE VOLTAGE www.analog.com Analog Devices │ 11 MAX40002–MAX40005 MAX40012–MAX40015 nanoPower 4-Bump Comparator in Ultra-Tiny 0.73mm x 0.73mm WLP/SOT23 Packages

*Future product—contact factory for availability. PART NUMBER INTERNAL REFERENCE VOLTAGE (V) INPUT OUTPUT TOP MARK MAX40002ANS+T — Noninverting OPEN-DRAIN +I MAX40002AUK+T* — Noninverting OPEN-DRAIN +AMHU MAX40002ANS02+T 0.2 Noninverting OPEN-DRAIN +M MAX40002AUK02+T 0.2 Noninverting OPEN-DRAIN +AMHV MAX40002ANS05+T* 0.5 Noninverting OPEN-DRAIN +N MAX40002AUK05+T* 0.5 Noninverting OPEN-DRAIN +AMHW MAX40002ANS12+T 1.2 Noninverting OPEN-DRAIN +P MAX40002AUK12+T* 1.2 Noninverting OPEN-DRAIN +AMHY MAX40003ANS+T* — Inverting OPEN-DRAIN +J MAX40003AUK+T* — Inverting OPEN-DRAIN +AMHZ MAX40003ANS02+T 0.2 Inverting OPEN-DRAIN +Q MAX40003AUK02+T* 0.2 Inverting OPEN-DRAIN +AMIA MAX40003ANS05+T* 0.5 Inverting OPEN-DRAIN +R MAX40003AUK05+T* 0.5 Inverting OPEN-DRAIN +AMIB MAX40003ANS12+T 1.2 Inverting OPEN-DRAIN +T MAX40003AUK12+T* 1.2 Inverting OPEN-DRAIN +AMID MAX40004ANS+T* — Noninverting PUSHPULL +K MAX40004AUK+T* — Noninverting PUSHPULL +AMIE MAX40004ANS02+T 0.2 Noninverting PUSHPULL +W MAX40004AUK02+T* 0.2 Noninverting PUSHPULL +AMIF MAX40004ANS05+T* 0.5 Noninverting PUSHPULL +X MAX40004AUK05+T* 0.5 Noninverting PUSHPULL +AMIG MAX40004ANS12+T* 1.2 Noninverting PUSHPULL +U MAX40004AUK12+T* 1.2 Noninverting PUSHPULL +AMIJ MAX40005ANS+T — Inverting PUSHPULL +L MAX40005AUK+T* — Inverting PUSHPULL +AMIK MAX40005ANS02+T 0.2 Inverting PUSHPULL +Z MAX40005AUK02+T* 0.2 Inverting PUSHPULL +AMIL MAX40005ANS05+T 0.5 Inverting PUSHPULL +1 MAX40005AUK05+T* 0.5 Inverting PUSHPULL +AMIM MAX40005ANS12+T* 1.2 Inverting PUSHPULL +V MAX40005AUK12+T* 1.2 Inverting PUSHPULL +AMIO MAX40012ANS09+T 0.9V Noninverting OPEN-DRAIN +4 MAX40012AUK09+T* 0.9V Noninverting OPEN-DRAIN +AMIS MAX40013ANS09+T* 0.9V Inverting OPEN-DRAIN +5 MAX40013AUK09+T* 0.9V Inverting OPEN-DRAIN +AMIT MAX40014ANS09+T 0.9V Noninverting PUSHPULL +6 MAX40014AUK09+T 0.9V Noninverting PUSHPULL +AMIU MAX40015ANS09+T* 0.9V Inverting PUSHPULL +7 MAX40015AUK09+T* 0.9V Inverting PUSHPULL +AMIV Selector Guide www.analog.com Analog Devices │ 12 MAX40002–MAX40005 MAX40012–MAX40015 nanoPower 4-Bump Comparator in Ultra-Tiny 0.73mm x 0.73mm WLP/SOT23 Packages

+Denotes a lead(Pb)-free/RoHS-compliant package. T = Tape and reel. *Future product—contact factory for availability. The “_ _” are placeholders for internal reference voltage level. For example, the MAX40002ANS05+T has an onboard 0.5V reference voltage. Devices without “_ _” use external reference voltage as supply voltage. PART TEMP RANGE PIN-PACKAGE MAX40002ANS+T -40°C to +125°C 4 WLP MAX40002ANS_ _+T -40°C to +125°C 4 WLP MAX40002AUK+T* -40°C to +125°C 5 SOT23 MAX40002AUK_ _+T -40°C to +125°C 5 SOT23 MAX40003ANS+T* -40°C to +125°C 4 WLP MAX40003ANS_ _+T -40°C to +125°C 4 WLP MAX40003AUK+T* -40°C to +125°C 5 SOT23 MAX40003AUK_ _+T* -40°C to +125°C 5 SOT23 MAX40004ANS+T* -40°C to +125°C 4 WLP MAX40004ANS_ _+T -40°C to +125°C 4 WLP MAX40004AUK+T* -40°C to +125°C 5 SOT23 MAX40004AUK_ _+T* -40°C to +125°C 5 SOT23 MAX40005ANS+T -40°C to +125°C 4 WLP MAX40005ANS_ _+T -40°C to +125°C 4 WLP MAX40005AUK+T -40°C to +125°C 5 SOT23 MAX40005AUK_ _+T* -40°C to +125°C 5 SOT23 MAX40012ANS09+T -40°C to +125°C 4 WLP MAX40013ANS09+T* -40°C to +125°C 4 WLP MAX40014ANS09+T -40°C to +125°C 4 WLP MAX40015ANS09+T* -40°C to +125°C 4 WLP MAX40012AUK09+T* -40°C to +125°C 5 SOT23 MAX40013AUK09+T* -40°C to +125°C 5 SOT23 MAX40014AUK09+T -40°C to +125°C 5 SOT23 MAX40015AUK09+T* -40°C to +125°C 5 SOT23 Ordering Information Chip Information PROCESS: BiCMOS www.analog.com Analog Devices │ 13 MAX40002–MAX40005 MAX40012–MAX40015 nanoPower 4-Bump Comparator in Ultra-Tiny 0.73mm x 0.73mm WLP/SOT23 Packages

PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO.

4 WLP N40C0+1 21-100103 Refer to Application Note AN1891

5 SOT23 U5+1 21-0057 90-0174

b SE SD

0.05 M S AB

B A E D Pin 1 Indicator Marking see Note 7 A2 A 0.05 S S FRONT VIEW TOP VIEW BOTTOM VIEW A 1 0.50 0.17 0.30 0.040 0.22 0.35 0.35 0.35 0.175 0.175 A AAAA SIDE VIEW 0.728 0.728 1 2 B TITLE DOCUMENT CONTROL NO. REV. 1 APPROVAL COMMON DIMENSIONS A b e SD SE MAX 0.03 0.03 BASIC REF BASIC NOTES: 1. Terminal pitch is defined by terminal center to center value. 2. Outer dimension is defined by center lines between scribe lines. 3. All dimensions in millimeter. 4. Marking shown is for package orientation reference only. 5. Tolerance is ± 0.02 unless specified otherwise. 6. All dimensions apply to PbFree (+) package codes only. 7. Front - side finish can be either Black or Clear. BASIC BASIC - DRAWING NOT TO SCALE - B BASIC BASIC maxim integrated TM 21-100103 PACKAGE OUTLINE 4 BUMPS THIN WLP PKG. 0.35 mm PITCH,N40C0+1 D 0.025 0.025E DEPOPULATED BUMPS: NONE

Package Information

For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. www.analog.com Analog Devices │ 14 MAX40002–MAX40005 MAX40012–MAX40015 nanoPower 4-Bump Comparator in Ultra-Tiny 0.73mm x 0.73mm WLP/SOT23 Packages

Package Information (continued) For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. www.analog.com Analog Devices │ 15 MAX40002–MAX40005 MAX40012–MAX40015 nanoPower 4-Bump Comparator in Ultra-Tiny 0.73mm x 0.73mm WLP/SOT23 Packages

0 3/17 Initial release — 1 4/17 Updated Selector Guide and Ordering Information tables to remove future product status from MAX40002AUK02+T, MAX40005ANS+T, and MAX40005AUK+T 11, 12 2 8/17 Updated Electrical Characteristics table and Selector Guide 2–4, 11 3 9/17 Removed future product asterisk from MAX40002ANS+T in Ordering Information and Selector Guide tables 11, 12 4 11/17 Updated Electrical Characteristics table and Selector Guide 2–4, 11 5 12/18 Updated Selector Guide and removed package outline drawing 11, 13 6 11/19 Updated part numbers in data sheet title and throughout document 1–14 7 1/20 Updated Electrical Characteristics, Selector Guide, and Ordering Information 4, 12, 13 8 5/20 Updated Electrical Characteristics, Selector Guide, Ordering Information, and Pack- age Information 4, 12–15 9 4/22 Updated Selector Guide and Ordering Information 12, 13

Revision History

MAX40002–MAX40005 MAX40012–MAX40015 nanoPower 4-Bump Comparator in Ultra-Tiny 0.73mm x 0.73mm WLP/SOT23 Packages www.analog.com Analog Devices │ 16 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use.Specifications subject to change without notice. No license is granted by implicationor otherwise under any patent or patent rights of Analog Devices. Trademarks andregistered trademarks are the property of their respective owners.