MADRCC0002 MACOM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 5
Technical content
Features
n Linearizes M/A-COM’s PIN Diode Vector Modulators Over a 360° Phase Range n Dual Channels Allow One Driver per Vector Modulator n Output Currents up to 12 mA n Operates with a Single Supply Voltage of +5V n Low Quiescent Currents n Single Control Voltage for Each Channel n 6 x 4 mm Chip Scale Package n Test Boards with Vector Modulators are Available n Tape and Reel Packaging Available
Description
M/A-COM's MADRCC0002 is a dual, break point free driver that produces a logarithmic output current suitable for lin earizing PIN diode based vector modulators. This driver, in conjunction with the external components, as defined in Figure 1, pr oduces a linearized transfer function between the input control voltage of the driver and the attenuation / phase output of the vector modulator. The MADRCC0002 has been optimized for linearizing M/A-COM’s Vector Modulators (see Table 1), but will function well with most types of cathode grounded vector modulators. The driver is packaged in a 6 x 4 mm Chip Scale Package fo r commercial SMT applications. A typical schematic for a dual linearizer driving a vector modulator is shown in Figure 1. Circuit Description: (Reference Figures 1, 2 and 3) Note that this is a dual driver. Only the top circuit will be described, because the bottom circuit is identical. The input divider, R1 and the sum of R2 and R3, sets the overall transfer function of the circuit. To increase the transfer function, decrease the Control Voltage and the value of R1. Temperature compensation is a function of the temperature coefficient of the thermistor, R3, and the ratio of R2 to R3, and can only be optimized once the transfer function and linearity component va lues have been established. Varying the value of R4 will optimize the linearity of the VVA. One can achieve a more linear transf er function by driving the attenuator over a smaller portion of its dynamic range. Note that when the vector modulators called o ut in Table 1 are driven with the dual linearizer, both amplitude and phase are affected, which makes it hard to define linearit y. The individual transfer function of each voltage variable attenuator in the vector modulator (See Figure 2 for the block di agram) is linearized as a function of voltage. The two VVAs in the block diagram are the quad hybrids that are terminated by two PIN diodes. See Figure 3 for the transfer function of the SA90 -0001 vector modulator (phase and attenuation vs. control voltages). Absolute Maximum Ratings 1 Parameter Absolute Maximum +VCC +20 V IN A, IN B -0.5V < Input < Vcc +0.5V REF A, REF B -0.5V < Input < Vcc +0.5V Output Short Circuit Current 20 mA Operating Temperature -40°C to +85°C Storage Temperature -65°C to +125°C Package Power Dissipation Control Voltage 150 mW Lead Temperature 300ºC for 10 seconds 1. Operation of this device above any one of these parameters may cause permanent damage.
Dual Linear Driver for Vector Modulators MADRCC0002 Specifications subject to change without notice. n North America: Tel. (800) 366-2266 n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020 Visit www.macom.com for additional data sheets and product information. V 2.00 Electrical Specifications, TA = +25°C, Reference Figure 1 (Each Circuit) Parameter Test Conditions Units Min Typical Max Output Drive Current Vcontrol = VCC mA 18 — — +VCC Supply Range — V 4.5 5.0 5.5 IN, REF Voltage — V 0 — VCC +VCC Quiescent Current No Load µA — 50 70 Settling Time 50% Ctl to 90%/10% RF µS — 25 — Figure 1
Specifications subject to change without notice. Visit www.macom.com for additional data sheets and product information. Table 1. Inductor Selection for M/A-COM Vector Modulators
Dual Linear Driver for Vector Modulators MADRCC0002 Specifications subject to change without notice. n North America: Tel. (800) 366-2266 n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020 Visit www.macom.com for additional data sheets and product information. V 2.00 Pin Configuration Pin # Function Pin # Function
1 NC 17 REF A
2 IN B 18 NC
3 NC 19 REF A
4 REF B 20 NC
5 NC 21 IN A
6 REF B 22 NC
7 NC 23 NC
8 REF B 24 NC
9 OUT B 25 NC
10 NC 26 NC
11 Vcc 27 NC
12 NC 28 GND
13 NC 29 NC
14 OUT A 30 NC
15 REF A 31 NC
16 NC 32 NC
MADRCC0002TR Tape & Reel (1K Reel) MAMDCC0005-DC000 Test Board with Circuit per Figure 1 (MAMDCC0005, GSM Vector Modulator) MAMDCC0002-DC000 Test Board with Circuit per Figure 1 (MAMDCC0002, PCS Vector Modulator) SA90-0001-DC000 Test Board with Circuit per Figure 1 SA90-0001, UMTS Vector Modulator
Ordering Information
Figure 2— Block Diagram Vector Modulator