MAC4DHM MOTOROLA | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

1Motorola Thyristor Device Data /C0083/C0101/C0110/C0115/C0105/C0116/C0105/C0118/C0101 /C0071/C0097/C0116/C0101 /C0084/C0082/C0073/C0065/C0067/C0083 Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.

  • Small Size Surface Mount DPAK Package
  • Passivated Die for Reliability and Uniformity
  • Four–Quadrant Triggering
  • Blocking Voltage to 600 V
  • On–State Current Rating of 4.0 Amperes RMS at 93°C
  • Low Level Triggering and Holding Characteristics

ORDERING INFORMATION

  • To Obtain “DPAK” in Surface Mount Leadform (Case 369A) Shipped in Sleeves — No Suffix, i.e. MAC4DHM Shipped in 16 mm Tape and Reel — Add “T4” Suffix to Device Number, i.e. MAC4DHMT4
  • To Obtain “DPAK” in Straight Lead Version (Case 369) Shipped in Sleeves — Add “–1” Suffix to Device Number, i.e. MAC4DHM–1 MAXIMUM RATINGS (TJ = 25°C unless otherwise noted) Rating Symbol Value Unit Peak Repetitive Off–State Voltage (1) (TJ = –40 to 110°C, Sine Wave, 50 to 60 Hz, Gate Open) MAC4DHM MAC4DLM VDRM 600 600 Volts On–State RMS Current (Full Cycle Sine Wave, 60 Hz, TC = 93°C) IT(RMS) 4.0 Amps Peak Non–Repetitive Surge Current (One Full Cycle, 60 Hz, TJ = 110°C) ITSM Circuit Fusing Consideration (t = 8.3 msec) I2t 6.6 A2sec Peak Gate Power (Pulse Width ≤ 10 /C0109sec, TC = 93°C) PGM 0.5 Watts Average Gate Power (t = 8.3 msec, TC = 93°C) PG(AV) 0.1 Peak Gate Current (Pulse Width ≤ 10 /C0109sec, TC = 93°C) IGM 0.2 Amps Peak Gate Voltage (Pulse Width ≤ 10 /C0109sec, TC = 93°C) VGM 5.0 Volts Operating Junction Temperature Range TJ –40 to 110 °C Storage Temperature Range Tstg –40 to 150 THERMAL CHARACTERISTICS Characteristic Symbol Max Unit Thermal Resistance — Junction to Case Thermal Resistance — Junction to Ambient Thermal Resistance — Junction to Ambient (2) R /C0113JC R /C0113JA R /C0113JA 3.5 °C/W Maximum Lead Temperature for Soldering Purposes (3) TL 260 °C (1) VDRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the device are exceeded. (2) Surface mounted on minimum recommended pad size. (3) 1/8″ from case for 10 seconds. Preferred devices are Motorola recommended choices for future use and best overall value. Order this document by MAC4DHM/D /C0077/C0079/C0084/C0079/C0082/C0079/C0076/C0065 SEMICONDUCTOR TECHNICAL DATA /C0077/C0065/C0067/C0052/C0068/C0072/C0077 /C0077/C0065/C0067/C0052/C0068/C0076/C0077 TRIACS

4.0 AMPERES RMS

600 VOLTS

CASE 369A–13 STYLE 6 MT2 MT1 G MT2 GMT2 MT1 Motorola Preferred Devices  Motorola, Inc. 1997

/C0077/C0065/C0067/C0052/C0068/C0072/C0077 /C0077/C0065/C0067/C0052/C0068/C0076/C0077

2 Motorola Thyristor Device Data

ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted) Characteristics Symbol Min Typ Max Unit Peak Repetitive Blocking Current (VD = Rated VDRM , Gate Open) T J = 25°C TJ = 110°C IDRM 0.01 2.0 mA Peak On–State Voltage (1) (ITM = ± 6.0 A) VTM — 1.3 1.6 Volts Gate Trigger Current (Continuous dc) (VD = 12 V, RL = 100 /C0087) MT2(+), G(+) MAC4DLM MT2(+), G(–) MT2(–), G(–) MT2(–), G(+) MT2(+), G(+) MAC4DHM MT2(+), G(–) MT2(–), G(–) MT2(–), G(+) IGT 1.8 2.1 2.4 4.2 1.8 2.1 2.4 4.2 3.0 3.0 3.0 5.0 5.0 5.0 5.0 mA Gate Trigger Voltage (Continuous dc) (VD = 12 V, RL = 100 /C0087) MT2(+), G(+) MT2(+), G(–) MT2(–), G(–) MT2(–), G(+) (VD = 12 V, RL = 10 K /C0087, TJ = 110°C) VGT 0.5 0.5 0.5 0.5 0.1 0.62 0.57 0.65 0.74 0.4 1.3 1.3 1.3 1.3 Volts Holding Current (VD = 12 V, Gate Open, IT = ± 200 mA) IH — 1.5 15 mA Latching Current MT2(+), G(+) (VD = 12 V, IG = 5.0 mA) MT2(+), G(–) (VD = 12 V, IG = 5.0 mA) MT2(–), G(–) (VD = 12 V, IG = 5.0 mA) MT2(–), G(+) (VD = 12 V, IG = 10 mA) IL 1.75 5.2 2.1 2.2 mA DYNAMIC CHARACTERISTICS Characteristics Symbol Min Typ Max Unit Rate of Change of Commutating Current (1) (VD = 200 V, ITM = 1.8 A, Commutating dv/dt = 1.0 V//C0109sec, TJ = 110°C, f = 250 Hz, CL = 5.0 /C0109fd, LL = 80 mH, RS = 56 /C0087, CS = 0.03 /C0109fd) See Figure 10 di/dt(c) — 3.0 — A/ms Critical Rate of Rise of Off–State Voltage (VD = 0.67 X Rated VDRM , Exponential Waveform, Gate Open, TJ = 110°C) dv/dt — 10 — V//C0109s (1) Pulse test: Pulse Width ≤ 2.0 msec, Duty Cycle ≤ 2%.

4 Motorola Thyristor Device Data

Figure 7. Typical Holding Current versus Figure 8. Typical Latching Current versus Figure 9. Exponential Static dv/dt versus Figure 10. Critical Rate of Rise of

0.1 COMMUTATING VOLTAGE (V/ s)/C0109

Figure 11. Simplified Test Circuit to Measure the Critical Rate of Rise of Commutating Voltage

200 VRMS

Note: Component values are for verification of rated (dv/dt)c. See AN1048 for additional information.

/C0077/C0065/C0067/C0052/C0068/C0072/C0077 /C0077/C0065/C0067/C0052/C0068/C0076/C0077

6 Motorola Thyristor Device Data

CASE 369A–13 ISSUE Y D A K B RV S F L G 2 PL M0.13 (0.005) T E C U J H –T– SEATING PLANE Z DIM MIN MAX MIN MAX MILLIMETERSINCHES A 0.235 0.250 5.97 6.35 B 0.250 0.265 6.35 6.73 C 0.086 0.094 2.19 2.38 D 0.027 0.035 0.69 0.88 E 0.033 0.040 0.84 1.01 F 0.037 0.047 0.94 1.19 G 0.180 BSC 4.58 BSC H 0.034 0.040 0.87 1.01 J 0.018 0.023 0.46 0.58 K 0.102 0.114 2.60 2.89 L 0.090 BSC 2.29 BSC R 0.175 0.215 4.45 5.46 S 0.020 0.050 0.51 1.27 V 0.030 0.050 0.77 1.27 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 12 3 STYLE 6: PIN 1. MT1 2. MT2 3. GATE 4. MT2 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution;JAPAN : Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4–32–1, P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447 Nishi–Gotanda, Shinagawa–ku, Tokyo 141, Japan. 81–3–5487–8488 – US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 INTERNET : http://motorola.com/sps MAC4DHM/D◊