M8BS-16U1-K

M8BS16 MSYSTEM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 14

Technical content

MODEL: M8BS-16 M8BS-16 SPECIFICATIONS ES-5490 Rev.14 Page 1/14 http://www.m-system.co.jp/ Dual Output Super-mini Signal Conditioners Pico-M Series INSTALLATION BASE (16 positions) Functions & Features

• Holding up to 16 modules of Pico-M series signal conditioners
• Power supplied through printed wiring on the base
• Saving wiring work within an instrumentational panel MODEL: M8BS-16[1]-[2][3]

ORDERING INFORMATION

• Code number: M8BS-16[1]-[2][3] Specify a code from below for each of [1] through [3]. (e.g. M8BS-16U1-KK/Q)
• Specify the specification for option code /Q (e.g. /C01) [1] CONNECTION (output 1/output 2) U0: Screw terminal block / Screw terminal block U1: Fujitsu FCN type connector / Screw terminal block U2: Fujitsu FCN type connector / Fujitsu FCN type connector U5: DDK connector / Screw terminal block K1: Azbil DCS J-HAM50/J-HMM00 module use / Screw terminal block K2: Azbil DCS J-AOM10 module use / Screw terminal block K3: Azbil DCS J-HAM50/J-HMM00 module use / Azbil DCS J-HAM50/J-HMM00 module use Y1: Yokogawa DCS VMx/PM1 card use / Screw terminal block Y2: Yokogawa DCS MAC2/PAC card use / Screw terminal block [2] POWER SUPPLY UNIT AC Power K: 85 – 132 V AC; single power source (Operational voltage range 85 – 132 V, 47 – 63 Hz) KK: 85 – 132 V AC; two independent power sources (Operational voltage range 85 – 132 V, 47 – 63 Hz) L: 170 – 264 V AC; single power source (Operational voltage range 170 – 264 V, 47 – 63 Hz) DC Power R: 24 V DC; no power supply unit (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) Redundant power supplies are recommended for long time use without interruption. [3] OPTIONS blank: none /Q: With options (specify the specification) SPECIFICATIONS OF OPTION: Q COATING (For the detail, refer to M-System's web site.) Only solder side of the main PWB is coated. /C01: Silicone coating /C02: Polyurethane coating /C03: Rubber coating GENERAL SPECIFICATIONS Capacity: 16 positions Connection Power input: M3.5 screw terminals (M4 for power codes KK and L) (torque 0.8 N·m) Input and output: M3.5 screw terminals (torque 0.8 N·m) Screw terminal: Nickel-plated steel Isolation: Input to output 1 to output 2 to power to FG Power indicator LED: ON with normal voltage level INSTALLATION Power Consumption
• AC: 130 VA min.
• DC: 2.5 A min. Operating temperature: 0 to 55°C (32 to 131°F) 0 to 50°C (32 to 122°F) for AC power Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Surface Weight M8BS-16U0: 1.8 kg (4.0 lb) for power code K, L 2.4 kg (5.3 lb) for power code KK 1.5 kg (3.3 lb) for power code R M8BS-16U1, U5, K1, K2, Y1, Y2: 1.6 kg (3.5 lb) for power code K, L 2.2 kg (4.9 lb) for power code KK 1.3 kg (2.9 lb) for power code R M8BS-16U2, K3: 1.4 kg (3.1 lb) for power code K, L 2.0 kg (4.4 lb) for power code KK 1.1 kg (2.4 lb) for power code R PERFORMANCE Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength:

1500 V AC @1 minute (input to output 1 or output 2 or

power to FG)

500 V AC @1 minute (output 1 to output 2 to power)

500 V AC @1 minute (output 1 or output 2 to FG for AC

MODEL: M8BS-16 M8BS-16 SPECIFICATIONS ES-5490 Rev.14 Page 2/14 http://www.m-system.co.jp/ power input) MOUNTING REQUIREMENTS unit: mm (inch) 465 (18.31) 4–M5 SCREW 50 (1.97) CONNECTION DIAGRAM ■ MODEL: M8BS-16U0 (screw terminal block / screw terminal block) ■ CONNECTION DIAGRAM A B C D Ch.1 INPUT A B C D Ch.16 INPUT PWR2 ■ Power Supply Unit Code R, K ■ Power Supply Unit Code KK, L FG 3 U V AC POWER PWR1 4 FG 3 U V AC POWER FG OUTPUT 1 A B C D Ch.1 INPUT A B C D Ch.16 INPUT OUTPUT 2 OUTPUT 1 OUTPUT 2 Ch.1 OUTPUT –Ch.16 OUTPUT OUTPUT 1 OUTPUT 2 OUTPUT 1 OUTPUT 2 Ch.1 OUTPUT –Ch.16 OUTPUT * For power supply unit code KK only. ** The input and output terminals are reversed for model M8YSx, M8YCx. Use either Output 1 or Output 2 terminal for the input. U(+) V(–) POWER

MODEL: M8BS-16 M8BS-16 SPECIFICATIONS ES-5490 Rev.14 Page 3/14 http://www.m-system.co.jp/ ■ MODEL: M8BS-16U1 (Fujitsu FCN type connector, FCN-364P040-AU / screw terminal block)

• Connector Pin Assignment CN1: Output 1 or input PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT A1 ch.1 + B1 ch.1 – A2 ch.2 + B2 ch.2 – A3 ch.3 + B3 ch.3 – A4 ch.4 + B4 ch.4 – A5 ch.5 + B5 ch.5 – A6 ch.6 + B6 ch.6 – A7 ch.7 + B7 ch.7 – A8 ch.8 + B8 ch.8 – A9 ch.9 + B9 ch.9 – A10 ch.10 + B10 ch.10 – A11 ch.11 + B11 ch.11 – A12 ch.12 + B12 ch.12 – A13 ch.13 + B13 ch.13 – A14 ch.14 + B14 ch.14 – A15 ch.15 + B15 ch.15 – A16 ch.16 + B16 ch.16 – A17 – A20, B17 – B20: Unused ■ CONNECTION DIAGRAM A B C D CN1 Ch.1 INPUT A B C D Ch.16 INPUT PWR2 4 FG 3 U V AC POWER PWR1 4 FG 3 U V AC POWER FG 3 A B C D CN1 Ch.1 INPUT A B C D Ch.16 INPUT OUTPUT 2 OUTPUT 2 Ch.1 OUTPUT Ch.16 OUTPUT OUTPUT 2 OUTPUT 2 Ch.1 OUTPUT Ch.16 OUTPUT ■ Power Supply Unit Code R, K ■ Power Supply Unit Code KK, L * For power supply unit code KK only. ** The input and output terminals are reversed for model M8YSx, M8YCx. Use either Output 1 (connector) or Output 2 terminal for the input. U(+) V(–) POWER

MODEL: M8BS-16 M8BS-16 SPECIFICATIONS ES-5490 Rev.14 Page 4/14 http://www.m-system.co.jp/ ■ MODEL: M8BS-16U2 (Fujitsu FCN type connector, FCN-364P040-AU / Fujitsu FCN type connector, FCN-364P040-AU)

• Connector Pin Assignment CN1: Output 1 or input CN2: Output 2 or input PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT A1 ch.1 + B1 ch.1 – A2 ch.2 + B2 ch.2 – A3 ch.3 + B3 ch.3 – A4 ch.4 + B4 ch.4 – A5 ch.5 + B5 ch.5 – A6 ch.6 + B6 ch.6 – A7 ch.7 + B7 ch.7 – A8 ch.8 + B8 ch.8 – A9 ch.9 + B9 ch.9 – A10 ch.10 + B10 ch.10 – A11 ch.11 + B11 ch.11 – A12 ch.12 + B12 ch.12 – A13 ch.13 + B13 ch.13 – A14 ch.14 + B14 ch.14 – A15 ch.15 + B15 ch.15 – A16 ch.16 + B16 ch.16 – A17 – A20, B17 – B20: Unused ■ CONNECTION DIAGRAM A B C D CN1 A B C D PWR2 4 FG 3 U V AC POWER PWR1 4 FG 3 U V AC POWER FG 3 A B C D CN1 CN2CN2 Ch.1 INPUT A B C D Ch.16 INPUT ■ Power Supply Unit Code R, K ■ Power Supply Unit Code KK, L Ch.1 INPUT Ch.16 INPUT * For power supply unit code KK only. ** The input and output terminals are reversed for model M8YSx, M8YCx. Use either Output 1 or Output 2 connector for the input. U(+) V(–) POWER

MODEL: M8BS-16 M8BS-16 SPECIFICATIONS ES-5490 Rev.14 Page 5/14 http://www.m-system.co.jp/ ■ MODEL: M8BS-16U5 (DDK connector, 17JE-13370-37 [D16B] / screw terminal block)

• Connector Pin Assignment CN1: Output 1 or input PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT 1 ch.1 + 20 ch.1 – 2 ch.2 + 21 ch.2 – 3 ch.3 + 22 ch.3 – 4 ch.4 + 23 ch.4 – 5 ch.5 + 24 ch.5 – 6 ch.6 + 25 ch.6 – 7 ch.7 + 26 ch.7 – 8 ch.8 + 27 ch.8 – 9 ch.9 + 28 ch.9 – 10 ch.10 + 29 ch.10 – 11 ch.11 + 30 ch.11 – 12 ch.12 + 31 ch.12 – 13 ch.13 + 32 ch.13 – 14 ch.14 + 33 ch.14 – 15 ch.15 + 34 ch.15 – 16 ch.16 + 35 ch.16 – 17 – 19, 36, 37: Unused ■ CONNECTION DIAGRAM A B C D CN1 Ch.1 INPUT A B C D Ch.16 INPUT PWR2 4 FG 3 U V AC POWER PWR1 4 FG 3 U V AC POWER FG 3 A B C D CN1 Ch.1 INPUT A B C D Ch.16 INPUT OUTPUT 2 OUTPUT 2 Ch.1 OUTPUT Ch.16 OUTPUT OUTPUT 2 OUTPUT 2 Ch.1 OUTPUT Ch.16 OUTPUT ■ Power Supply Unit Code R, K ■ Power Supply Unit Code KK, L * For power supply unit code KK only. ** The input and output terminals are reversed for model M8YSx, M8YCx. Use either Output 1 (connector) or Output 2 terminal for the input. U(+) V(–) POWER

MODEL: M8BS-16 M8BS-16 SPECIFICATIONS ES-5490 Rev.14 Page 6/14 http://www.m-system.co.jp/ ■ MODEL: M8BS-16K1 (Azbil DCS J-HAM50/J-HMM00 module use / screw terminal block) I/O cable : J-RSL / J-RSK J-RRL / J-RRK

• Location Input connector : 57GE-40500-751 CN1: J-HAM50 / J-HMM00 module use The output 1 is connected to the connector. Pico-M LOCATION NO. AZBIL DCS AI CONNECTOR 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ CONNECTION DIAGRAM A B C D CN1 Ch.1 INPUT A B C D Ch.16 INPUT PWR2 4 FG 3 U V AC POWER PWR1 4 FG 3 U V AC POWER FG 3 A B C D CN1 Ch.1 INPUT A B C D Ch.16 INPUT OUTPUT 2 OUTPUT 2 Ch.1 OUTPUT Ch.16 OUTPUT OUTPUT 2 OUTPUT 2 Ch.1 OUTPUT Ch.16 OUTPUT ■ Power Supply Unit Code R, K ■ Power Supply Unit Code KK, L * For power supply unit code KK only. ** The input and output terminals are reversed for model M8YSx, M8YCx. Use either Output 1 (connector) or Output 2 terminal for the input. U(+) V(–) POWER

MODEL: M8BS-16 M8BS-16 SPECIFICATIONS ES-5490 Rev.14 Page 7/14 http://www.m-system.co.jp/ ■ MODEL: M8BS-16K2 (Azbil DCS J-AOM10 module use / screw terminal block) I/I/O cable : J-RSL / J-RSK J-RRL / J-RRK

• Location Output connector: 57GE-40500-751 CN1: J-AOM10 module use The input is connected to the connector. Install the Extender Module (model: M8BWx) to unused channels in order to close the circuit. Pico-M LOCATION NO. AZBIL DCS AO CONNECTOR 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ CONNECTION DIAGRAM A B C D CN1 Ch.1 OUTPUT A B C D Ch.16 OUTPUT PWR2 4 FG 3 U V AC POWER PWR1 4 FG 3 U V AC POWER FG U(+) V(–) POWER A B C D CN1 Ch.1 OUTPUT A B C D Ch.16 OUTPUT Ch.1 INPUT Ch.16 INPUT Ch.1 INPUT Ch.16 INPUT ■ Power Supply Unit Code R, K ■ Power Supply Unit Code KK, L * For power supply unit code KK only. ** The input terminals are not usable for J-AOM10 module. The input and output terminals are reversed for models other than the M8YSx, M8YCx.

MODEL: M8BS-16 M8BS-16 SPECIFICATIONS ES-5490 Rev.14 Page 8/14 http://www.m-system.co.jp/ ■ MODEL: M8BS-16K3 (Azbil DCS J-HAM50/J-HMM00 module use / Azbil DCS J-HAM50/JHMM00 module use)

• Connector Pin Assignment (CN1, CN2) PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT 3 ch.1 + 4 ch.1 – 5 ch.2 + 6 ch.2 – 7 ch.3 + 8 ch.3 – 9 ch.4 + 10 ch.4 – 27 ch.5 + 26 ch.5 – 29 ch.6 + 28 ch.6 – 31 ch.7 + 30 ch.7 – 33 ch.8 + 32 ch.8 – 11 ch.9 + 12 ch.9 – 13 ch.10 + 14 ch.10 – 15 ch.11 + 16 ch.11 – 17 ch.12 + 18 ch.12 – 19 ch.13 + 20 ch.13 – 21 ch.14 + 22 ch.14 – 23 ch.15 + 24 ch.15 – 25 ch.16 + 50 ch.16 – 34 – 47: Unused 1 – 2, 48 – 49 are connected. I/O cable : J-RSL / J-RSK J-RRL / J-RRK
• Location Input connector : 57GE-40500-751 CN1: J-HAM50 / J-HMM00 module use (output 1) CN2: J-HAM50 / J-HMM00 module use (output 2) Pico-M LOCATION NO. AZBIL DCS AI CONNECTOR 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ CONNECTION DIAGRAM A B C D CN1 A B C D PWR2 4 FG 3 U V AC POWER PWR1 4 FG 3 U V AC POWER FG 3 A B C D CN1 CN2CN2 Ch.1 INPUT A B C D Ch.16 INPUT ■ Power Supply Unit Code R, K ■ Power Supply Unit Code KK, L Ch.1 INPUT Ch.16 INPUT * For power supply unit code KK only. ** The input and output terminals are reversed for model M8YSx, M8YCx. Use either Output 1 or Output 2 connector for the input. U(+) V(–) POWER

MODEL: M8BS-16 M8BS-16 SPECIFICATIONS ES-5490 Rev.14 Page 9/14 http://www.m-system.co.jp/ ■ MODEL: M8BS-16Y1 (Yokogawa DCS VMx/PM1 card use (PS-40PE-D4T1-PN1) / screw terminal block)

• Location CN1: VMx / PM1 card use* The input or output 1 is connected to the connector. VM1/PM1/VM4 CARD INPUT or OUTPUT 1ɹ 2 ɹ 3 ɹ 4 ɹ 5 ɹ 6 ɹ 7 ɹ 8 ɹ9ɹ10 ɹ11 ɹ12 ɹ13 ɹ14 ɹ15 ɹ16 1ɹ 2 ɹ 3 ɹ 4 ɹ 5 ɹ 6 ɹ 7 ɹ 8 ɹ9ɹ10 ɹ11 ɹ12 ɹ13 ɹ14 ɹ15 ɹ16 VM2 CARD INPUT NO. VM2 CARD OUTPUT NO. 1ɹ 2 ɹ 3 ɹ 4 ɹ 5 ɹ 6 ɹ 7 ɹ 8 1ɹ 2ɹ 3ɹ 4ɹ 5ɹ 6ɹ 7ɹ 8 Pico-M LOCATION NO. *VMx / PM1 card (uses KS2 cable) VM1: analog input 16 points VM2: analog input 8 points / analog output 8 points VM4: analog output 16 points PM1: pulse input 16 points ■ CONNECTION DIAGRAM A B C D CN1 Ch.1 INPUT A B C D Ch.16 INPUT PWR2 4 FG 3 U V AC POWER PWR1 4 FG 3 U V AC POWER FG 3 A B C D CN1 Ch.1 INPUT A B C D Ch.16 INPUT OUTPUT 2 OUTPUT 2 Ch.1 OUTPUT Ch.16 OUTPUT OUTPUT 2 OUTPUT 2 Ch.1 OUTPUT Ch.16 OUTPUT ■ Power Supply Unit Code R, K ■ Power Supply Unit Code KK, L * For power supply unit code KK only. ** The input and output terminals are reversed for model M8YSx, M8YCx. Use either Output 1 (connector) or Output 2 terminal for the input. U(+) V(–) POWER

MODEL: M8BS-16 M8BS-16 SPECIFICATIONS ES-5490 Rev.14 Page 10/14 http://www.m-system.co.jp/ ■ MODEL: M8BS-16Y2 (Yokogawa DCS MAC2/PAC card use (PS-40PE-D4T1-PN1) / screw terminal block) 1ɹ 2 ɹ 3 ɹ 4 ɹ 5 ɹ 6 ɹ 7 ɹ 8 ɹ9 10 11 12 13 14 15 16 1ɹ 1 ɹ 2 ɹ 2 ɹ 3 ɹ 3 ɹ 4 ɹ 4 ɹ5ɹ5ɹ 6 ɹ 6 ɹ7 ɹ7ɹ8ɹ 8 iɹ oɹ i ɹ o ɹ iɹ oɹ i ɹ oɹiɹ o ɹ iɹ oɹ iɹ oɹiɹ o *The MAC2 card (uses KS1 cable) is used to control I/O in Yokogawa DCS. Input and output, each 8 points, are paired and located as shown above. The PAC card I/O allocation is the same as that for the MAC2 card, except that pulse input modules are used. Pico-M LOCATION NO.

• Location CN1: MAC2 / PAC card use* CN2: MAC2 / PAC card use* (dual redundancy) The input or output 1 is connected to the connector. MAC2/PAC CARD INPUT (i) or OUTPUT (o) ■ CONNECTION DIAGRAM A B C D CN1 Ch.1 INPUT A B C D Ch.16 INPUT PWR2 4 FG 3 U V AC POWER PWR1 4 FG 3 U V AC POWER FG U(+) V(–) POWER A B C D CN1 CN2CN2 Ch.1 INPUT A B C D Ch.16 INPUT ■ Power Supply Unit Code R, K ■ Power Supply Unit Code KK, L OUTPUT 2 OUTPUT 2 Ch.1 OUTPUT Ch.16 OUTPUT OUTPUT 2 OUTPUT 2 Ch.1 OUTPUT Ch.16 OUTPUT * For power supply unit code KK only. ** The input and output terminals are reversed for model M8YSx, M8YCx. Use either Output 1 (connector) or Output 2 terminal for the input.

MODEL: M8BS-16 M8BS-16 SPECIFICATIONS ES-5490 Rev.14 Page 11/14 http://www.m-system.co.jp/ EXTERNAL DIMENSIONS unit: mm (inch) ■ M8BS-16U0-K, R 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 CH1 CH8 CH9 CH16 C D C D C D C D C D C D C D C D CH8CH1 A B A B A B A B A B A B A B A B C D C D C D C D C D C D C D C D CH16CH9 A B A B A B A B A B A B A B A B + – + 95 (3.74) 50 (1.97) 64–M3.5 INPUT TERMINALS 87 (3.43) 7.3(.29) 64–M3.5 OUTPUT TERMINALS 3–M3.5 POWER TERMINALS POWER LED 8.6 (.34) 17 (.67) 440 (17.32) 465 (18.31) 480 (18.90) 7.3 (.29) OUTPUT 2 TERM. OUTPUT 1 TERM. *1. Included with M8CTx. CT PROTECTOR (CTR) *1 ■ M8BS-16U0-KK, L 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CH1 CH8 CH9 CH16 C D C D C D C D C D C D C D C D CH8CH1 A B A B A B A B A B A B A B A B C D C D C D C D C D C D C D C D CH16CH9 A B A B A B A B A B A B A B A B + – + PWR1PWR2 95 (3.74) 50 (1.97) 7.3(.29) 64–M3.5 OUTPUT TERMINALS 17 (.67) 440 (17.32) 465 (18.31) 480 (18.90) 64–M3.5 INPUT TERMINALS 7.3 (.29) 5–M4 POWER TERMINALS 8.5 (.34) POWER UNITS*1 POWER LED*2 135 (5.31) 87 (3.43) POWER LED *3 OUTPUT 2 TERM. OUTPUT 1 TERM. *1. PWR2 provided only for power supply unit code KK. *2. For power supply unit code KK. *3. For power supply unit code L. *4. Included with M8CTx. CT PROTECTOR (CTR) *4

MODEL: M8BS-16 M8BS-16 SPECIFICATIONS ES-5490 Rev.14 Page 12/14 http://www.m-system.co.jp/ ■ M8BS-16U1, U2, U5, K1, K2, K3, Y2-K, R 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 CH1 CH8 CH9 CH16 C D C D C D C D C D C D C D C D CH8CH1 A B A B A B A B A B A B A B A B C D C D C D C D C D C D C D C D CH16CH9 A B A B A B A B A B A B A B A B 88 (3.46) 50 (1.97) 64–M3.5 INPUT TERMINALS 87 (3.43) 7.2(.28) 32–M3.5 OUTPUT TERMINALS *1 3–M3.5 POWER TERMINALS 8.6 (.34) 17 (.67) CN1 CONNECTORS POWER LED 440 (17.32) 465 (18.31) 480 (18.90) 7.3 (.29) CN2 *2 *1. Not provided for M8BS-16U2 or K3. *2. For M8BS-16U2, K3 or Y2 only. *3. Included with M8CTx. CT PROTECTOR (CTR) *3 ■ M8BS-16U1, U2, U5, K1, K2, K3, Y2-KK, L 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CH1 CH8 CH9 CH16 C D C D C D C D C D C D C D C D CH8CH1 A B A B A B A B A B A B A B A B C D C D C D C D C D C D C D C D CH16CH9 A B A B A B A B A B A B A B A B 88 (3.46) 50 (1.97) 64–M3.5 INPUT TERMINALS 135 (5.31) 7.2(.28) 32–M3.5 OUTPUT TERMINALS*4 5–M4 POWER TERMINALS 8.5 (.34) POWER UNITS*1 POWER LED*2 87 (3.43) 17 (.67) 7.3 (.29) 440 (17.32) 465 (18.31) 480 (18.90) CN1 CONNECTORS CN2*5 POWER LED*3 *1. PWR2 provided only for power supply unit code KK. *2. For power supply unit code KK. *3. For power supply unit code L. *4. Not provided for M8BS-16U2 or K3. *5. For M8BS-16U2, K3 or Y2 only. *6. Included with M8CTx. CT PROTECTOR (CTR) *6

MODEL: M8BS-16 M8BS-16 SPECIFICATIONS ES-5490 Rev.14 Page 13/14 http://www.m-system.co.jp/ ■ M8BS-16Y1-K, R 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 CH1 CH8 CH9 CH16 C D C D C D C D C D C D C D C D CH8CH1 A B A B A B A B A B A B A B A B C D C D C D C D C D C D C D C D CH16CH9 A B A B A B A B A B A B A B A B 88 (3.46) 50 (1.97) 64–M3.5 INPUT TERMINALS 87 (3.43) 7.2(.28) 32–M3.5 OUTPUT TERMINALS 3–M3.5 POWER TERMINALS 8.6 (.34) 17 (.67) CN1 CONNECTOR POWER LED 440 (17.32) 465 (18.31) 480 (18.90) 7.3 (.29) *1. Included with M8CTx. CT PROTECTOR (CTR) *1 ■ M8BS-16Y1-KK, L 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CH1 CH8 CH9 CH16 C D C D C D C D C D C D C D C D CH8CH1 A B A B A B A B A B A B A B A B C D C D C D C D C D C D C D C D CH16CH9 A B A B A B A B A B A B A B A B 88 (3.46) 50 (1.97) 64–M3.5 INPUT TERMINALS 135 (5.31) 7.2(.28) 32–M3.5 OUTPUT TERMINALS 5–M4 POWER TERMINALS 8.5 (.34) POWER UNITS*1 POWER LED*2 87 (3.43) 17 (.67) 7.3 (.29) 440 (17.32) 465 (18.31) 480 (18.90) CN1 CONNECTOR POWER LED*3 *1. PWR2 provided only for power supply unit code KK. *2. For power supply unit code KK. *3. For power supply unit code L. *4. Included with M8CTx. CT PROTECTOR (CTR) *4

MODEL: M8BS-16 M8BS-16 SPECIFICATIONS ES-5490 Rev.14 Page 14/14 http://www.m-system.co.jp/ Specifications are subject to change without notice.