M74HC07 STMICROELECTRONICS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 10

Technical content

■ HIGH SPEED: tPD = 6ns (TYP .) at VCC =6 V ■ LOW POWER DISSIPATION: ICC =1 µA(MAX.) at TA=25°C ■ HIGH NOISE IMMUNITY: VNIH =V NIL =2 8%V CC (MIN.) ■ WIDE OPERATING VOLTAGE RANGE: V CC (OPR) = 2V to 6V ■ PIN AND FUNCTION COMPATIBLE WITH

74 SERIES 07

DESCRIPTION

The M74HC07 is an high speed CMOS HEX OPEN DRAIN BUFFER fabricated with silicon gate C 2MOS technology. The internal circuit is composed of 2 stages including buffer output, which enables high noise immunity and stable output. All inputs are equipped with protection circuits against static discharge and transient excess voltage. M74HC07 HEX BUFFER (OPEN DRAIN) PIN CONNECTION AND IEC LOGIC SYMBOLS ORDER CODES PACKAGE TUBE T & R DIP M74HC07B1R SOP M74HC07M1R M74HC07RM13TR TSSOP M74HC07TTR TSSOPDIP SOP

INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION TRUTH TABLE Z : High Impedance ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied (*) 500mW at 65 °C; derate to 300mW by 10mW/°Cf r o m6 5°Ct o8 5°C RECOMMENDED OPERATING CONDITIONS PIN No SYMBOL NAME AND FUNCTION 1, 3, 5, 9, 11, 13 1A to 6A Data Inputs 2, 4, 6, 8, 10, 12 1Y to 6Y Data Outputs

7 GND Ground (0V)

14 VCC Positive Supply Voltage

Symbol Parameter Value Unit VCC Supply Voltage -0.5 to +7 V VI DC Input Voltage -0.5 to V CC + 0.5 V V O DC Output Voltage -0.5 to V CC + 0.5 V IIK DC Input Diode Current ± 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 25 mA ICC or IGND DC V CC or Ground Current ± 50 mA P D Power Dissipation 500(*) mW Tstg Storage Temperature -65 to +150 °C TL Lead Temperature (10 sec) 300 °C Symbol Parameter Value Unit VCC Supply Voltage 2t o6 V VI Input Voltage 0 to V CC V V O Output Voltage 0 to V CC V Top Operating Temperature -55 to 125 °C tr,tf Input Rise and Fall Time V CC = 2.0V 0 to 1000 ns VCC = 4.5V 0 to 500 ns VCC = 6.0V 0 to 400 ns

AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr =tf=6 n s ) Symbol Parameter Test Condition Value UnitVCC (V) TA = 25°C -40 to 85°C -55 to 125°C V IH High Level Input Voltage 2.0 1.5 1.5 1.5 V4.5 3.15 3.15 3.15 6.0 4.2 4.2 4.2 VIL Low Level Input Voltage 2.0 0.5 0.5 0.5 V4.5 1.35 1.35 1.35 6.0 1.8 1.8 1.8 VOL Low Level Output Voltage V II Input Leakage Current 6.0 VI=V CC or GND ± 0.1 ± 1 ± 1 µA IOZ Output Leakage Current 6.0 VI=V IH or VIL VO =V CC or GND ±0.5 ± 5 ± 10 µA ICC Quiescent Supply Current 6.0 VI=V CC or GND 11 0 2 0 µA Symbol Parameter Test Condition Value UnitV CC (V) TA = 25°C -40 to 85°C -55 to 125°C tTHL Output Transition Time 2.0 30 75 95 110 ns4.5 8 15 19 22 6.0 7 13 16 19 tPLZ Propagation Delay Time 2.0 R L =1K Ω 10 90 115 135 ns4.5 7 18 23 27 6.0 6 15 20 23 tPZL Propagation Delay Time 2.0 R L =1K Ω 17 90 115 135 ns4.5 7 18 23 27 6.0 5 15 20 23

CAPACITIVE CHARACTERISTICS 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr)=C PD xV CC xfIN +ICC /6 (per gate) TEST CIRCUIT C L = 50pF or equivalent (includes jig and probe capacitance) R T =Z OUT of pulse generator (typically 50Ω ) WAVEFORM : PROPAGATION DELAY TIME (f=1MHz; 50% duty cycle) Symbol Parameter Test Condition Value UnitVCC (V) TA = 25°C -40 to 85°C -55 to 125°C C IN Input Capacitance 5.0 5 10 10 10 pF C OUT Output Capacitance 5.0 3 pF C PD Power Dissipation Capacitance (note 5.0 4 pF

DIM. mm. inch a1 0.51 0.020 B 1.39 1.65 0.055 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 15.24 0.600 F 7.1 0.280 I 5.1 0.201 L 3.3 0.130 Z 1.27 2.54 0.050 0.100 Plastic DIP-14 MECHANICAL DATA P001A

DIM. mm. inch A 1.75 0.068 a1 0.1 0.2 0.003 0.007 a2 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45˚ (typ.) D 8.55 8.75 0.336 0.344 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 7.62 0.300 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M 0.68 0.026 S ˚ (max.) SO-14 MECHANICAL DATA PO13G

DIM. mm. inch A 1.2 0.047 b 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 e 0.65 BSC 0.0256 BSC K0 ˚ 8 ˚0 ˚ 8 ˚ TSSOP14 MECHANICAL DATA c Eb A2A D PIN 1 IDENTIFICATION LKe 0080337D

DIM. mm. inch A 330 12.992 C 12.8 13.2 0.504 0.519 D 20.2 0.795 N 60 2.362 T 22.4 0.882 Ao 6.4 6.6 0.252 0.260 Bo 9 9.2 0.354 0.362 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 Tape & Reel SO-14 MECHANICAL DATA

DIM. mm. inch A 330 12.992 C 12.8 13.2 0.504 0.519 D 20.2 0.795 N 60 2.362 T 22.4 0.882 Ao 6.7 6.9 0.264 0.272 Bo 5.3 5.5 0.209 0.217 Ko 1.6 1.8 0.063 0.071 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 Tape & Reel TSSOP14 MECHANICAL DATA

Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2003 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. © http://www.st.com