M6NPP MSYSTEM | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

MODEL: M6NPP M6NPP SPECIFICATIONS ES-7919 Rev.6 Page 1/5 http://www.m-system.co.jp/ Screw Terminal Ultra-Slim Signal Conditioners M6N Series PULSE ISOLATOR Functions & Features

  • 7.5-mm wide ultra-slim design
  • Low profile allows the M6N module mounted in a 120-mm deep panel
  • Galvanically isolates pulse rate signals
  • High-density mounting
  • Power indicator and input monitor LED Typical Applications
  • Isolating field pulse signals in order to reduce noises
  • Changing e.g. dry contact signal to e.g. 5 V signals mm (inch) 7.5 (.30) 102 (4.02) 102 (4.02) MODEL: M6NPP–[1][2][3]–R[4]

ORDERING INFORMATION

  • Code number: M6NPP-[1][2][3]-R[4] Specify a code from below for each [1] through [4]. (e.g. M6NPP-CMN-R/Q)
  • Specify the specification for option code /Q (e.g. /C01) [1] INPUT A1: Open collector A2: Mechanical contact C: 5 V pulse (sensitivity 2 V) D: 12 V/24 V pulse (sensitivity 5 V) H: Two-wire current pulse [2] OUTPUT A1: High frequency open collector (max. 100 kHz) A2: Low frequency open collector (max. 30 Hz) M: 5 V pulse N: 12 V pulse P: 24 V pulse [3] OUTPUT LOGIC N: The same as the input R: Inverted POWER INPUT DC Power R: 24 V DC (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) [4] OPTIONS blank: none /Q: With options (specify the specification) SPECIFICATIONS OF OPTION: Q COATING (For the detail, refer to M-System's web site.) /C01: Silicone coating /C02: Polyurethane coating GENERAL SPECIFICATIONS Connection Input and output: M3 screw terminal (torque 0.5 N·m) Power input: Via the Installation Base (model: M6NBS) or M3 screw terminal (torque 0.5 N·m) Recommended solderless terminal: Max. 5.8 mm (0.23”) wide; Ones with insulation sleeve do not fit. Applicable wire size: 0.2 – 2.5 mm2 Housing material: Flame-resistant resin (black) Isolation: Input to output to power Chattering protection: Filter provided for mechanical contact input Power LED: Green light turns on when the power is supplied. Input monitor LED Open collector, Mechanical contact: Orange LED turns on when the input is ON. Voltage pulse, 2-wire current pulse: Orange LED turns on when the input is high. Input pulse sensing: DC coupled ■Recommended solderless terminal (unit: mm (inch)) 3.2 (.13) dia. 4 min. (.16) 5.8 max. (.23) 5.5 max. (.22) INPUT SPECIFICATIONS Excitation: 12 V DC @20 mA, shortcircuit protection ■ Open Collector Maximum frequency: 100 kHz Pulse width time requirement: ≥ 5 μsec. for ON and OFF

MODEL: M6NPP M6NPP SPECIFICATIONS ES-7919 Rev.6 Page 2/5 http://www.m-system.co.jp/ Sensing: Approx. 11 V DC @2.4 mA Detecting levels: ≤ 1.8 kΩ/3 V for ON, ≥ 4 kΩ/5 V for OFF ■ Mechanical Contact Maximum frequency: 30 Hz Pulse width time requirement: ≥ 10 msec. for ON and OFF Sensing: Approx. 11 V DC @2.4 mA Detecting levels: ≤ 1.8 kΩ/3 V for ON, ≥ 4 kΩ/5 V for OFF ■ Voltage Pulse Maximum frequency: 100 kHz Pulse width time requirement: ≥ 5 μsec. for high and low levels Waveform: Square or sine Input impedance: ≥ 10 kΩ Max. voltage between input terminals: 50 V Detecting H level

5 V pulse: ≥ 3 V

12 V, 24 V pulse: ≥ 6 V

5 V pulse: ≤ 1 V

12 V, 24 V pulse: ≤ 4 V

■ Two-wire Current Pulse Max. frequency: 100 kHz Input resistance: Receiving resistor 200 Ω Input range: 0 – 25 mA Detecting levels: ≤ 5 mA for Lo, ≥ 15 mA for Hi OUTPUT SPECIFICATIONS ■ High Frequency Open Collector:

50 V DC @100 mA (resistive load)

Maximum frequency: 100 kHz Saturation voltage: 0.5 V DC ■ Low Frequency Open Collector: Maximum frequency: 30 Hz Timer: Limits ≥ 75 msec. within 75 ±25 msec. ON time for output logic non-inverted OFF time for output logic inverted Saturation voltage: 0.5 V DC ■ Voltage Pulse Maximum frequency: 100 kHz High level: Rating (5, 12 or 24 V) ±10 % Low level: ≤ 0.5 V Load resistance: ≥ 1.0 kΩ for 5 V ≥ 2.4 kΩ for 12 V ≥ 4.8 kΩ for 24 V INSTALLATION Power consumption: Approx. 1 W Operating temperature: -20 to +55°C (-4 to +131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Installation Base (model: M6NBS) or DIN rail Weight: 60 g (2.1 oz) PERFORMANCE Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 2000 V AC @1 minute (input to output to power to ground) STANDARDS & APPROVALS EU conformity: EMC Directive EMI EN 61000-6-4 EMS EN 61000-6-2 RoHS Directive EN 50581

MODEL: M6NPP M6NPP SPECIFICATIONS ES-7919 Rev.6 Page 3/5 http://www.m-system.co.jp/ EXTERNAL VIEW (With the cover open) Power LED Input Monitor LED OUTPUT LOGIC OFF OFF HH H H OFF ON OFF ON H L H L OFF ON OFF ON ON LL L L ON INPUT TYPE Voltage Pulse Input 2-wire Current Pulse Input Mechanical Contact Input Open Collector Input PULSE LOGIC Non Inverted Inverted Non Inverted Inverted INPUT VOLTAGE PULSE OUTPUT OPEN COLLECTOR OUTPUT

MODEL: M6NPP M6NPP SPECIFICATIONS ES-7919 Rev.6 Page 4/5 http://www.m-system.co.jp/ EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch) 102 (4.02) 7.5 (.30) DIN RAIL HOOK 102 (4.02) [1 (.04)] 8–M3 SCREW TERMINAL WIRE INSERTION ANGLE : approx. 35° SCREWDRIVER INSERTION ANGLE : approx. 55° SCREWDRIVER INSERTION ANGLE : approx. 40° DIN RAIL 35mm wide 5 6 7 8 1 2 3 4

  • When mounting, no extra space is needed between units.*Screwdriver stem diameter: 6 mm (.24”) or less

MODEL: M6NPP M6NPP SPECIFICATIONS ES-7919 Rev.6 Page 5/5 http://www.m-system.co.jp/ SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Isolation Waveform Shaper Output Driver

12 V Supply

  • Low freq. open collector output only. ■ Mechanical Contact or Open Collector Input Connection Examples ■ Voltage Pulse +12V ■ Open Collector Output Connection Examples ■ Voltage Pulse PWR PWR + 3 + 3 POWER LED INPUT MONITOR LED ■ 2-Wire Current Pulse
  • External DC Supply 2-WIRE PICK-UP 2-WIRE PICK-UP DC SUPPLY
  • Built-in Excitation OUTPUT POWER CONNECTOR POWER 200 Ω +12V5 kΩ +12V 200 Ω +12V Specifications are subject to change without notice.