M6NPA MSYSTEM | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

MODEL: M6NPA M6NPA SPECIFICATIONS ES-7904 Rev.9 Page 1/4 http://www.m-system.co.jp/ Screw Terminal Ultra-Slim Signal Conditioners M6N Series FREQUENCY TRANSMITTER Functions & Features

  • 7.5-mm wide ultra-slim design
  • Low profile allows the M6N module mounted in a 120-mm deep panel
  • Converts the output from a pulse-type transducer into a standard process signal
  • High-density mounting
  • Power indicator LED mm (inch) 7.5 (.30) 102 (4.02) 102 (4.02) MODEL: M6NPA–[1][2]–R[3]

ORDERING INFORMATION

  • Code number: M6NPA-[1][2]-R[3] Specify a code from below for each [1] through [3]. (e.g. M6NPA-CA-R/UL/Q)
  • Frequency range (e.g. 0 – 1 kHz)
  • Special output range (For codes Z & 0)
  • Specify the specification for option code /Q (e.g. /C01) [1] INPUT A1: Open collector A2: Mechanical contact C: 5 V pulse (sensitivity 2 V) D: 24 V pulse (sensitivity 10 V) [2] OUTPUT Current A: 4 – 20 mA DC (Load resistance 550 Ω max.) Z: Specify current (See OUTPUT SPECIFICATIONS) Voltage 4: 0 – 10 V DC (Load resistance 10 kΩ min.) 5: 0 – 5 V DC (Load resistance 5000 Ω min.) 6: 1 – 5 V DC (Load resistance 5000 Ω min.) 4W: -10 – +10 V DC (Load resistance 20 kΩ min.) 5W: -5 – +5 V DC (Load resistance 10 kΩ min.) 0: Specify voltage (See OUTPUT SPECIFICATIONS) POWER INPUT DC Power R: 24 V DC (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) [3] OPTIONS (multiple selections) Standards & Approvals blank: CE marking /UL: UL approval, CE marking Other Options blank: none /Q: Option other than the above (specify the specification) SPECIFICATIONS OF OPTION: Q COATING (For the detail, refer to M-System's web site.) /C01: Silicone coating /C02: Polyurethane coating GENERAL SPECIFICATIONS Connection Input and output: M3 screw terminal (torque 0.5 N·m) Power input: Via the Installation Base (model: M6NBS) or M3 screw terminal (torque 0.5 N·m) Recommended solderless terminal: Max. 5.8 mm (0.23”) wide; Ones with insulation sleeve do not fit. Applicable wire size: 0.2 – 2.5 mm2 Housing material: Flame-resistant resin (black) Isolation: Input to output to power Zero adjustment: -2 to +2 % (front) (Output code 4W, 5W: Adjustable at 0V.) Span adjustment: 98 to 102 % (front) Chattering protection: Filter provided for mechanical contact input Power LED: Green light turns on when the power is supplied. ■Recommended solderless terminal (unit: mm (inch)) 3.2 (.13) dia. 4 min. (.16) 5.8 max. (.23) 5.5 max. (.22) INPUT SPECIFICATIONS ■ Open Collector Frequency range: 0 – 0.01 Hz through 100 kHz Pulse width time requirement: ≥ 4 µsec. for both H and L

MODEL: M6NPA M6NPA SPECIFICATIONS ES-7904 Rev.9 Page 2/4 http://www.m-system.co.jp/ levels Sensing voltage/current: 2.5 V DC @1 mA (approx.) Detecting levels: ≤ 750 Ω/0.75 V for ON; ≥ 3 kΩ/1.6 V for OFF ■ Mechanical Contact Frequency range: 0 – 0.01 Hz through 30 Hz Pulse width time requirement: ≥ 10 msec. for both ON and OFF Sensing voltage/current: 2.5 V DC @1 mA (approx.) Detecting levels: ≤ 750 Ω/0.75 V for ON; ≥ 3 kΩ/1.6 V for OFF ■ Voltage Pulse Frequency range: 0 – 0.01 Hz through 100 kHz Pulse width time requirement: ≥ 4 µsec. for both H and L levels Waveform: Square or sine Input impedance: ≥ 10 kΩ Max. voltage between input terminals: ±50 V Detecting H level

5 V pulse: ≥ 3 V

24 V pulse: ≥ 14 V

5 V pulse: ≤ 1 V

24 V pulse: ≤ 6 V

■ DC Current: 2 – 20 mA DC (and 0 – 1 mA DC) Minimum span: 1 mA Offset: Max. 1.5 times span Load resistance: Output drive 11 V max. ■ DC Voltage: 0 – 10 V DC Minimum span: 1 V Offset: Max. 1.5 times span Load resistance: Output drive 1 mA max.; at ≥ 1 V INSTALLATION Power consumption: Approx. 0.5 W Operating temperature: -20 to +55°C (-4 to +131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Installation Base (model: M6NBS) or DIN rail Weight: 60 g (2.1 oz) PERFORMANCE in percentage of span Accuracy: ±0.1 % Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) Response time: Max. 0.5 sec. + 1 pulse cycle (0 – 90 %) Line voltage effect: ±0.1 % over voltage range Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 2000 V AC @1 minute (input to output to power to ground) STANDARDS & APPROVALS EU conformity: EMC Directive EMI EN 61000-6-4 EMS EN 61000-6-2 RoHS Directive EN 50581 Approval: UL/C-UL nonincendive Class I, Division 2, Groups A, B, C, and D hazardous locations (ANSI/ISA-12.12.01, CAN/CSA-C22.2 No.213) UL/C-UL general safety requirements (UL 61010-1, CAN/CSA-C22.2 No.61010-1)

MODEL: M6NPA M6NPA SPECIFICATIONS ES-7904 Rev.9 Page 3/4 http://www.m-system.co.jp/ EXTERNAL VIEW (With the cover open) Zero Adj. Power LED Span Adj. EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch) 102 (4.02) 7.5 (.30) DIN RAIL HOOK 102 (4.02) [1 (.04)] 8–M3 SCREW TERMINAL WIRE INSERTION ANGLE : approx. 35° SCREWDRIVER INSERTION ANGLE : approx. 55° SCREWDRIVER INSERTION ANGLE : approx. 40° DIN RAIL 35mm wide 5 6 7 8 1 2 3 4

  • When mounting, no extra space is needed between units.*Screwdriver stem diameter: 6 mm (.24”) or less

MODEL: M6NPA M6NPA SPECIFICATIONS ES-7904 Rev.9 Page 4/4 http://www.m-system.co.jp/ SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Output Driver + OUTPUT IsolationSZ Voltage Amplifier Digital Computation Waveform Shaper1 INPUT 2.4 kΩ ■ Open Collector or Mechanical Contact Input Connection Examples ■ Voltage Pulse 2.5 V POWER POWER LED POWER CONNECTOR Specifications are subject to change without notice.