M675-01-BH

M675 IDT | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

M675 Datasheet Rev 0.5 2 of 6 Revised 29Jul2009 Integrated Device Technology, Inc. ● Communication Modules ● www.idt.com ● tel (508) 852-5400 M675 VOLTAGE CONTROLLED SAW OSCILLATOR Preliminary Information PIN DESCRIPTIONS Number Name I/O Configuration Description 1V I N Input Frequency control input. 2C L K _ E N Input Internal pull-up resistor 1 Clock enable: Logic 1 enables normal operation. Logic 0 stops the output clock; nFOUT is held high, FOUT is held low. 3G N D Ground Power supply ground connection. FOUT nFOUT Output No internal terminator Clock output pair. Differential LVPECL. 6V C C Power Power supply connection, connect to + 3.3V. Table 2: Pin Descriptions Note 1: See “Clock Enable Pull-up” in Table 5 (DC Characteristics for M675-01 on pg. 3) and Table 7 (DC Characteristics for M675-02 on pg. 4). ABSOLUTE MAXIMUM RATINGS1 Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only. Functional operation of product at these conditions or any conditions beyond those listed in Recommended Conditions of Operation, DC Characteristics, or AC Characteristics is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. Symbol Parameter Rating Unit VI Inputs -0.5 to VCC +0.5 V VO Outputs -0.5 to VCC +0.5 V VCC Power Supply Voltage 4.6 V TS Storage Temperature -55 to +125 oC Table 3: Absolute Maximum Ratings RECOMMENDED CONDITIONS OF OPERATION Symbol Parameter Min Typ Max Unit VCC Positive Supply Voltage 2.97 3.3 3.63 V TA Ambient Operating Temperature -40 25 +85 oC Table 4: Recommended Conditions of Operation

M675 Datasheet Rev 0.5 3 of 6 Revised 29Jul2009 Integrated Device Technology, Inc. ● Communication Modules ● www.idt.com ● tel (508) 852-5400 M675 VOLTAGE CONTROLLED SAW OSCILLATOR Preliminary Information ELECTRICAL SPECIFICATIONS FOR M675-01 DC Characteristics for M675-01 Unless stated otherwise, VCC = 3.3 Volts + 10%, TA = 0 to 85 oC, VCSO Freq.s = 155.52 MHz, Outputs terminated into 180Ω to ground Symbol Parameter Pin Min Typ Max Unit Power Supply VCC Positive Supply Voltage VCC 2.97 3.3 3.63 V ICC Power Supply Current 85 125 mA Control Voltage VIN Input Control Voltage Range VIN 0 3.3 V VIN Input Impedence 100 kΩ Clock Enable Pull-up1 Note 1: Internally pulled up to Logic 1 (normal operation) if left unselected. VIH Input High Voltage CLK_EN 2 Vcc + 0.3 V VIL Input Low Voltage -0.3 0.8 V IIH Input High Current 5 µA IIL Input Low Current -150 µA Rpullup Internal Pull-up Resistor 51 kΩ Differential Outputs VOH Output High Voltage FOUT, nFOUT Vcc - 0.98 Vcc - 0.75 V VOL Output Low Voltage Vcc - 1.95 Vcc - 1.63 V VP-P Peak to Peak Output Voltage2 Note 2: Single-ended measurement. See Figure 3, Output Rise and Fall Time, on pg. 5. 0.450 0.625 0.85 VP-P IOUT Output Current 20 mA Table 5: DC Characteristics for M675-01 AC Characteristics for M675-01 Unless stated otherwise, VCC = 3.3 Volts + 10%, TA = 0 to 85 oC, VCSO Freq. = 155.52 MHz, Outputs terminated into 180Ω to ground Symbol Parameter Min Typ Max Unit Notes Control Voltage VIN Modulation Bandwidth VIN 500 kHz Output FOUT Output Center Frequency Range M675-01 125 175 MHz Note 1: Also fully meets ±50 ppm minimum pull- range specification that is commonly required. ±100 ppm fSTAB Frequency Stability 100 ppm p-p At any givin VIN LIN Tuning Linearity 6 % VIN = 0.3 to 3.0V Best fit straight line KVCO VCO Gain 400 ppm/V VIN = 0.3 to 3.0V Non-harmonic Spurious -50 -77 dBc Φ n SSB (single sideband) Phase Noise, offset from carrier 100Hz Offset -52 dBc/Hz 1kHz Offset -80 dBc/Hz 10kHz Offset -112 dBc/Hz 100kHz Offset -136 dBc/Hz 1MHz Offset -146 dBc/Hz J(t) Jitter (rms) 12kHz to 20MHz 0.36 ps rms 50kHz to 80MHz 0.50 ps rms odc Output Duty Cycle 2 Note 2: See Parameter Measurement Information on pg. 5. 45 55 % tR Output Rise Time 2 for FOUT, nFOUT 275 425 ps 20% to 80% tF Output Fall Time 2 for FOUT, nFOUT 275 425 ps 20% to 80% Table 6: AC Characteristics for M675-01

M675 Datasheet Rev 0.5 4 of 6 Revised 29Jul2009 Integrated Device Technology, Inc. ● Communication Modules ● www.idt.com ● tel (508) 852-5400 M675 VOLTAGE CONTROLLED SAW OSCILLATOR Preliminary Information ELECTRICAL SPECIFICATIONS FOR M675-02 DC Characteristics for M675-02 Unless stated otherwise, VCC = 3.3 Volts + 10%, TA = 0 to 85 oC, VCSO Freq. = 622.08 MHz, Outputs terminated into 180Ω to ground Symbol Parameter Pin Min Typ Max Unit Power Supply VCC Positive Supply Voltage VCC 2.97 3.3 3.63 V ICC Power Supply Current 85 125 mA Control Voltage VIN Input Control Voltage Range VIN 0 3.3 V VIN Input Impedence 100 kΩ Clock Enable Pull-up1 Note 1: Internally pulled up to Logic 1 (normal operation) if left unselected. VIH Input High Voltage CLK_EN 2 Vcc + 0.3 V VIL Input Low Voltage -0.3 0.8 V IIH Input High Current 5 µA IIL Input Low Current -150 µA Rpullup Internal Pull-up Resistor 51 kΩ Differential Outputs VOH Output High Voltage FOUT, nFOUT Vcc - 0.98 Vcc - 0.75 V VOL Output Low Voltage Vcc - 1.95 Vcc - 1.63 V VP-P Peak to Peak Output Voltage2 Note 2: Single-ended measuremen t. See Figure 3, Output Rise and Fall Time, on pg. 5. 0.450 0.625 0.85 VP-P IOUT Output Current 20 mA Table 7: DC Characteristics for M675-02 AC Characteristics for M675-02 Unless stated otherwise, VCC = 3.3 Volts + 10%, TA = 0 to 85 oC, VCSO Freq. = 622.08 MHz, Outputs terminated into 180Ω to ground Symbol Parameter Min Typ Max Unit Notes Control Voltage VIN Modulation Bandwidth VIN 500 kHz Output FOUT Output Center Frequency Range M675-02 500 700 MHz Note 1: Also fully meets ±50 ppm minimum pull -range specification that is commonly required. ±100 ppm fSTAB Frequency Stability 100 ppm p-p At any givin VIN LIN Tuning Linearity 6 % VIN = 0.3 to 3.0V Best fit straight line KVCO VCO Gain 400 ppm/V VIN = 0.3 to 3.0V Non-harmonic Spurious -50 -77 dBc Φ n SSB (single sideband) Phase Noise, offset from carrier 100Hz Offset -48 dBc/Hz 1kHz Offset -75 dBc/Hz 10kHz Offset -99 dBc/Hz 100kHz Offset -124 dBc/Hz 1MHz Offset -142 dBc/Hz J(t) Jitter (rms) 12kHz to 20MHz 0.30 ps rms 50kHz to 80MHz 0.18 ps rms odc Output Duty Cycle 2 Note 2: See Parameter Measurement Information on pg. 5. 45 55 % tR Output Rise Time 2 for FOUT, nFOUT 275 400 ps 20% to 80% tF Output Fall Time 2 for FOUT, nFOUT 275 400 ps 20% to 80% Table 8: AC Characteristics for M675-02

M675 Datasheet Rev 0.5 6 of 6 Revised 29Jul2009 Integrated Device Technology, Inc. ● Communication Modules ● www.idt.com ● tel (508) 852-5400 While the information presented herein has been checked for both accuracy and reliabi lity, Integrated Circuit Systems (ICS) assumes no responsibility for either its use or for the infringemen t of any patents or other rights of third parties, which wou ld result from its use. No other ci rcuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices o r critical medical instruments. M675 VOLTAGE CONTROLLED SAW OSCILLATOR Preliminary Information

ORDERING INFORMATION

Figure 6: Part Numbering Scheme Example Order Numbers M675-01 Standard Output Frequencies & Order Codes M675-02 Standard Output Frequencies & Order Codes Consult IDT for the availability of other frequencies For Output Frequencies Order Part # M675-01-Bx For Output Frequencies Order Part # M675-02-Ax 155.5200 M675-01-BA 622.0800 M675-02-AA 156.2500 M675-01-BB 625.0000 M675-02-AB 161.1328 M675-01-BD 644.5313 M675-02-AD 167.3316 M675-01-BH 669.3266 M675-02-AH Table 9: Example Order Numbers M675 Part Number: M680-01 - xx See Tables 10 and 11 at right for frequency order codes. Output Frequency Order Code Device Number Consult ICS for other frequencies and order codes. M675 Variant -01 = Output Frequencies 125 - 175 MHz -02 = Output Frequencies 500 - 700 MHz -0y 125.0000 DA 168.0407 BJ 155.5200 BA 172.6423 BK 156.2500 BB 173.3708 BL 156.8324 BC 164.3555 BM 161.1328 BD 153.6000 BO 166.6286 BE 118.7500 BP 167.2820 BF 176.8382 BQ 167.3280 BG 156.1762 BR 167.3316 BH 174.1537 BU 167.7097 BI 174.7031 BV Table 10: M675-01 Standard Output Frequencies & Order Codes 500.0000 CA 672.1627 AJ 622.0800 AA 690.5692 AK 625.0000 AB 693.4830 AL 627.3296 AC 657.4219 AM 644.5313 AD 614.4000 AO 666.5143 AE 475.0000 AP 669.1281 AF 707.3527 AQ 669.3120 AG 624.7048 AR 669.3266 AH 696.6149 AU 670.8386 AI 698.8123 AV Table 11: M675-02 Standard Output Frequencies & Order Codes