M40E-70A105RA0 SICK | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
M40S-70A105AA0, M40E-70A105RA0 M4000 Area MULTIPLE LIGHT BEAM SAFETY DEVICES
A B C D E F H I J K L M N O P Q R S T M40S-70A105AA0, M40E-70A105RA0 | M4000 Area MULTIPLE LIGHT BEAM SAFETY DEVICES
Ordering information
System part Type Part no. Sender M40S-70A105AA0 1200149 Receiver M40E-70A105RA0 1200148 Other models and accessories www.sick.com/M4000_Area Detailed technical data
Features
Scanning range 0.5 m ... 70 m, configurable Low scanning range 0.5 m ... 20 m Great scanning range 9 m ... 70 m Length of the monitored area 1,800 mm Resolution 80 mm Response time 17 ms Synchronization Optical synchronisation Safety-related parameters Type Type 4 (IEC 61496) Safety integrity level SIL3 (IEC 61508) SILCL3 (EN 62061) Category Category 4 (EN ISO 13849) Performance level PL e (EN ISO 13849) PFHD (mean probability of a dangerous fail- ure per hour) 1.4 * E-08 (EN ISO 13849) TM (mission time) 20 years (EN ISO 13849) Safe state in the event of a fault At least one OSSD is in the OFF state. Functions Functions Delivery status Restart interlock ✔ Internal External device monitoring (EDM) ✔ Activated Beam coding ✔ Uncoded Sender test ✔ Deactivated Configurable scanning range ✔ 0.5 m ... 20 m Configurable application diagnostic output ✔ Contamination (OWS) Safe SICK device communication via EFI ✔
2 OPTO-ELECTRONIC PROTECTIVE DEVICES | SICK Online data sheet | 2017-08-24 18:11:25
Subject to change without notice
M40S-70A105AA0, M40E-70A105RA0 | M4000 Area MULTIPLE LIGHT BEAM SAFETY DEVICES Interfaces System connection Connection type Hirschmann male connector M26, 12-pin Permitted cable length ≤ 50 m 1) Permitted cross-section ≥ 0.75 mm² Configuration method PC with CDS (Configuration and Diagnostic Software) Configuration connection Connection type Female connector M8, 4-pin Display elements LEDs 7-segment display Fieldbus, industrial network Integration via EFI gateways CANopen, Ethernet, PROFIBUS DP, PROFIBUS PROFIsafe, PROFINET PROFIsafe 2) Integration via Flexi Soft safety controller CANopen, DeviceNet™, EtherCAT®, EtherNet/IP™, Modbus TCP, PROFIBUS DP, PROFINET 3) 1) Depending on load, power supply and wire cross-section. The technical specifications must be observed. 2) For a suitable EFI-gateway see modules and gateways in the accessory section of connection systems. 3) For additional information on Flexi Soft -> www.sick.com/Flexi_Soft. Electrical data Protection class III (EN 50178) Residual ripple ≤ 10 % 2) Power consumption ≤ 0.2 A: ≤ 0.6 A (depending on type) Safety outputs (OSSD) Type of output 2 PNP semiconductors, short-circuit protected, cross-circuit monitored 3) Switching voltage HIGH 24 V DC (VS – 2.25 V DC ... VS) Switching voltage LOW ≤ 2 V DC Switching current ≤ 500 mA Diagnostic outputs Type of output PNP semiconductor, short-circuit protected Switching voltage HIGH 24 V DC (VS – 4.2 V DC ... VS) Switching voltage LOW High resistance Switching current ≤ 100 mA 1) The external voltage supply must be capable of buffering brief mains voltage failures of 20 ms as specified in EN 60204-1. Suitable power supplies are available as accessories from SICK. 2) Within the limits of VS. 3) Applies to the voltage range between –30 V and +30 V. Mechanical data Housing cross-section 52 mm x 55.5 mm Housing material Aluminum alloy ALMGSI 0.5 Surface treatment Powder coated Front screen material Polycarbonate, scratch-resistant coating Ambient data Enclosure rating IP65 (EN 60529) 2017-08-24 18:11:25 | Online data sheet Subject to change without notice OPTO-ELECTRONIC PROTECTIVE DEVICES | SICK 3
A B C D E F H I J K L M N O P Q R S T M40S-70A105AA0, M40E-70A105RA0 | M4000 Area MULTIPLE LIGHT BEAM SAFETY DEVICES Ambient operating temperature –30 °C ... +55 °C Storage temperature –30 °C ... +70 °C Air humidity 15 % ... 95 %, Non-condensing Vibration resistance 5 g, 10 Hz ... 55 Hz (IEC 60068-2-6) Shock resistance 10 g, 16 ms (IEC 60068-2-29) Other information Wave length 950 nm Classifications ECl@ss 5.0 27272703 ECl@ss 5.1.4 27272703 ECl@ss 6.0 27272703 ECl@ss 6.2 27272703 ECl@ss 7.0 27272703 ECl@ss 8.0 27272703 ECl@ss 8.1 27272703 ECl@ss 9.0 27272703 ETIM 5.0 EC001832 ETIM 6.0 EC001832 UNSPSC 16.0901 46171620
4 OPTO-ELECTRONIC PROTECTIVE DEVICES | SICK Online data sheet | 2017-08-24 18:11:25
Subject to change without notice
M40S-70A105AA0, M40E-70A105RA0 | M4000 Area MULTIPLE LIGHT BEAM SAFETY DEVICES Dimensional drawing (Dimensions in mm (inch)) (0.55) (0.24) 2.2 (0.09) 10.5 (0.41) (0.04) 3.5 (0.14) (2.05) (2.05) S 14.4 (0.57) 14.4 (0.57) 71.2 (2.80) 71.2 (2.80) S 25.5 (1.00) 55.5 (2.19) 27.5 (1.08) M4000 Area 60 M4000 Area 80 Sliding nut groove for side mounting Ca. 125 (4.92) (connector range) Cable socket M26 with crimp contacts (for DIN 43651) 87 (3.43) 2017-08-24 18:11:25 | Online data sheet Subject to change without notice OPTO-ELECTRONIC PROTECTIVE DEVICES | SICK 5
A B C D E F H I J K L M N O P Q R S T M40S-70A105AA0, M40E-70A105RA0 | M4000 Area MULTIPLE LIGHT BEAM SAFETY DEVICES Length of the monitored area S L1 L2 Connection diagram M4000 Area connected to UE10-3OS safety relay 0 V 2) PELV +24 V M4000S Area FE M4000R Area FE 1 1 GND FE OSSD1 OSSD2 ADO RR EFib EFia EDM +24 V RES n.c. FE GND n.c. n.c. EFIb EFIa n.c. n.c. n.c. +24 V Test n.c.1 1 B1 B3 Y1 13 23 33 41 1) B2 B4 Y2 14 24 34 42 UE10-3OS E119955/00/2014-07-29 Task Connection of an M4000 Area multiple light beam safety device to a UE10-3OS safety relay. Operating mode: with restart interlock and external device monitoring. Operating characteristics When the light path is clear and the UE10-3OS is de-energized and functioning correctly, the yellow LED on the receiver and the H3 lamp flash. The system is ready for switch-on and waits for an input signal/switch-on signal. The system is enabled by pressing and releasing the S1 button. The OSSD1 and OSSD2 outputs are live, the UE10-3OS is switched on. On interruption of one or several of the light beams, the UE10-3OS is de-energized by the OSSD1 and OSSD2 outputs. If the optics are dirty, H2 indicator illuminates. Fault analysis OSSD cross-circuits and short-circuits are detected and lead to the inhibited state (lock-out). The erroneous behavior of the UE10-3OS will be detected. The shutdown function is retained. On manipulation (e.g., jamming) of the S1 button, the system does not enable the output current circuits. Comments 1) Output circuits: These contacts are to be connected to the controller such that, with the output circuit open, the dangerous state is disabled. For categories 4 and 3, this integration must be dual-channel (x/y paths). Single-channel insertion in the control (z path) is only possible with a single-channel control and by taking the risk analysis into account. 2) PELV in accordance with the requirements in EN 60204-1 / 6.4 Take note of the operating instructions of the integrated devices. This applies particularly to the use of configurable functions.
6 OPTO-ELECTRONIC PROTECTIVE DEVICES | SICK Online data sheet | 2017-08-24 18:11:25
Subject to change without notice
M40S-70A105AA0, M40E-70A105RA0 | M4000 Area MULTIPLE LIGHT BEAM SAFETY DEVICES Recommended accessories Other models and accessories www.sick.com/M4000_Area Brief description Type Part no. Mounting brackets and plates 4 pieces, Mounting kit 1, mounting bracket, rigid, L-shaped, including fixing screws and washers BEF-3WNGBAST4 7021352 Other mounting accessories 2 pieces, Floor stands for the horizontal mounting of the safety light curtains C4000 Fusion, Entry/Exit, Palletizer, as well as the multi-beam safety light curtain M4000 Area, for mounting heights of between 70 mm and 780 mm., Includes mounting bracket BEF-3HHOCAST2 2041661 Terminal and alignment brackets 4 pieces, Mounting kit 6, side bracket, rotatable, Zinc diecast BEF-1SHABAZN4 2019506 4 pieces, Mounting kit 12, rotatable, swivel mount BEF-2SMGEAKU4 2030510 Plug connectors and cables Head A: female connector, M26, 12-pin, straight Head B: cable Cable: PVC, unshielded, 5 m DOL-0612G05M075KM0 2022545 Head A: female connector, M26, 12-pin, straight Head B: cable Cable: PVC, unshielded, 10 m DOL-0612G10M075KM0 2022547 Head A: female connector, M26, 12-pin, straight Head B: cable Cable: PVC, unshielded, 20 m DOL-0612G20M075KM0 2022549 Head A: female connector, M26, 12-pin, straight Head B: - Cable: unshielded DOS-0612G000GA3KM0 6020757 Head A: female connector, M26, 12-pin, angled Head B: - Cable: unshielded DOS-0612W000GA3KM0 6020758 Alignment aids Laser alignment aid for various sensors, laser class 2 (IEC 60825). Do not look into the beam! AR60 1015741 Adapter AR60 for M4000 and M4000 Curtain AR60 adapter, M4000 4040006 2017-08-24 18:11:25 | Online data sheet Subject to change without notice OPTO-ELECTRONIC PROTECTIVE DEVICES | SICK 7
SICK AG | Waldkirch | Germany | www.sick.com SICK At A GlAnCe SICK is one of the leading manufacturers of intelligent sensors and sensor solutions for industrial applica- tions. A unique range of products and services creates the perfect basis for controlling processes securely and efficiently, protecting individuals from accidents and preventing damage to the environment. We have extensive experience in a wide range of industries and understand their processes and require- ments. With intelligent sensors, we can deliver exactly what our customers need. In application centers in Europe, Asia and North America, system solutions are tested and optimized in accordance with customer specifications. All this makes us a reliable supplier and development partner. Comprehensive services complete our offering: SICK lifetime Services provide support throughout the ma- chine life cycle and ensure safety and productivity. For us, that is “Sensor Intelligence.” WOrldWIde preSenCe: Contacts and other locations – www.sick.com