M36P0R9070E0 STMICROELECTRONICS | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 26
Technical content
Datasheet sections
- 1 Summary description
- 2 Signal descriptions
- 2.1 Address inputs (A0-A24)
- 2.2 Data input/output (DQ0-DQ15)
- 2.3 Latch Enable (L)
- 2.4 Clock (K)
- 2.5 Wait (WAIT)
- 2.6 Flash Chip Enable input (EF)
- 2.7 Flash Output Enable inputs (GF)
- 2.8 Flash Write Enable (WF)
- 2.9 Flash Write Protect (WPF)
- 2.10 Flash Reset (RPF)
- 2.11 PSRAM Chip Enable input (EP)
- 2.12 PSRAM Write Enable (WP)
- 2.13 PSRAM Output Enable (GP)
- 2.14 PSRAM Upper Byte Enable (UBP)
- 2.15 PSRAM Lower Byte Enable (LBP)
- 2.16 PSRAM Configuration Register Enable (CRP)
- 2.17 Deep Power-Down input (DPDF)
- 2.18 V DDF Supply Voltages
- 2.19 V CCP Supply Voltage
- 2.20 V DDQ Supply Voltage
- 2.21 V PPF Program Supply Voltage
- 2.22 V SS Ground
- 3 Functional description
- 4 Maximum rating
- 5 DC and AC parameters
This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. Rev. 1 November 2005 1/26 M36P0R9070E0
512 Mbit (x16, Multiple Bank, Multi-Level, Burst) Flash Memory
128 Mbit (Burst) PSRAM, 1.8V Supply, Multi-Chip Package Features summary ■ Multi-chip package – 1die of 512 Mbit (32Mb x 16, Multiple Bank, Multi-Level, Burst) Flash Memory –1 die of 128Mbit (8Mb x16) PSRAM ■ Supply voltage –V DDF = VCCP = VDDQ = 1.7 to 1.95V –V PPF = 9V for fast program (12V tolerant) ■ Electronic signature – Manufacturer Code: 20h – Device Code: 8819 ■ Package –E C O P A C K ® Flash memory ■ Synchronous / asynchronous read – Synchronous Burst Read mode: 108MHz, 66MHz – Asynchronous Page Read mode – Random Access: 93ns ■ Programming time – 4µs typical Word program time using Buffer Enhanced Factory Program command ■ Memory organization – Multiple Bank Memory Array: 64 Mbit Banks – Four Extended Flash Array (EFA) Blocks of
64 Kbits
■ Dual operations – program/erase in one Bank while read in others – No delay between read and write operations ■ Security – 2112-bit user programmable OTP Cells – 64-bit unique device number ■ 100,000 program/erase cycles per block ■ Block locking – All Blocks locked at power-up – Any combination of Blocks can be locked with zero latency –W P F for Block Lock-Down – Absolute Write Protection with VPPF = VSS ■ Common Flash Interface (CFI) PSRAM ■ Access time: 70ns ■ Asynchronous Page Read – Page Size: 4, 8 or 16 Words – Subsequent read within page: 20ns ■ Low power features – Partial Array Self Refresh (PASR) – Deep Power-Down mode (DPD) ■ Synchronous Burst Read/Write TFBGA107 (ZAC) FBGA
1 Summary description M36P0R9070E0
1 Summary description
- 512-Mbit Multiple Bank Flash memory (the M58PR512J).
- 128 Mbit PSRAM (the M69KB128AA). This datasheet should be read in conjunction with the M58PR512J and M69KB128AA datasheets, which are available from www.st.com. Recommended operating conditions do not allow more than one memory to be active at the same time. The memory is offered in a Stacked TFBGA107 package. It is supplied with all the bits erased (set to ‘1’).
Table 1. Logic Diagram
Table 2. Signal Names Note: 1 A23-A24 are Address Inputs for the Flash memory component only.
Figure 1. TFBGA Connections (Top view through package)
M36P0R9070E0 2 Signal descriptions
2 Signal descriptions
See Table 1., Logic Diagram and Table 2., Signal Names, for a brief overview of the signals connected to this device.
2.1 Address inputs (A0-A24)
Addresses A0-A22 are common inputs for the Flash memory and PSRAM components. Addresses A23 and A24 are inputs for Flash memory components only. The Address Inputs select the cells in the memory array to access during Bus Read operations. During Bus Write operations they control the commands sent to the Command Interface of the internal state machine. The Flash memory is accessed through the Chip Enable signal (E F) and through the Write Enable signal (WF), while the PSRAM is accessed through the Chip Enable signal (EP) and the Write Enable signal (WP). EF Low, and EP must not be Low at the same time.
2.2 Data input/output (DQ0-DQ15)
The Data I/O output the data stored at the selected address during a Bus Read operation or input a command or the data to be programmed during a Bus Write operation. For the PSRAM component, the upper Byte Data Inputs/Outputs (DQ8-DQ15) carry the data to or from the upper part of the selected address when Upper Byte Enable (UBP) is driven Low. The lower Byte Data Inputs/Outputs (DQ0-DQ7) carry the data to or from the lower part of the selected address when Lower Byte Enable (LB P) is driven Low. When both UBP and LBP are disabled, the Data Inputs/ Outputs are high impedance.
2.3 Latch Enable (L)
The Latch Enable pin is common to the Flash memory and PSRAM components. For details of how the Latch Enable signal behaves, please refer to the datasheets of the respective memory components: M69KB128AA for the PSRAM and M58PR512J for the Flash memory.
2.4 Clock (K)
The Clock input pin is common to the Flash memory and PSRAM components. For details of how the Clock signal behaves, please refer to the datasheets of the respective memory components: M69KB128AA for the PSRAM and M58PR512J for the Flash memory.
2 Signal descriptions M36P0R9070E0
2.5 Wait (WAIT)
WAIT is an output pin common to the Flash memory and PSRAM components. However the WAIT signal does not behave in the same way for the PSRAM and the Flash memory. For details of how it behaves, please refer to the M69KB128AA datasheet for the PSRAM and to the M58PR512J datasheet for the Flash memory.
2.6 Flash Chip Enable input (EF)
The Flash Chip Enable input activates the control logic, input buffers, decoders and sense amplifiers of the Flash memory component selected. When Chip Enable is Low, VIL, and Reset is High, VIH, the device is in active mode. When Chip Enable is at VIH the corresponding Flash memory are deselected, the outputs are high impedance and the power consumption is reduced to the standby level. It is not allowed to have EF at VIL and EP at VIL at the same time. Only one memory component can be enabled at a time.
2.7 Flash Output Enable inputs (GF)
The Output Enable pins control the data outputs during Flash memory Bus Read operations.
2.8 Flash Write Enable (WF)
The Write Enable controls the Bus Write operation of the Flash memory Command Interface. The data and address inputs are latched on the rising edge of Chip Enable or Write Enable whichever occurs first.
2.9 Flash Write Protect (WPF)
Write Protect is an input that gives an additional hardware protection for each block. When Write Protect is Low, V IL, Lock-Down is enabled and the protection status of the Locked-Down blocks cannot be changed. When Write Protect is at High, VIH, Lock-Down is disabled and the Locked-Down blocks can be locked or unlocked. (See the Lock Status Table in the M58PR512J datasheet).
2.10 Flash Reset (RPF)
The Reset input provides a hardware reset of the Flash memories. When Reset is at VIL, the memory is in Reset mode: the outputs are high impedance and the current consumption is reduced to the Reset Supply Current I DD2 . Refer to Table 7., Flash Memory DC Characteristics - Currents, for the value of IDD2 . After Reset all blocks are in the Locked state and the Configuration Register is reset. When Reset is at VIH, the device is in normal operation. Exiting Reset mode the device enters Asynchronous Read mode, but a negative transition of Chip Enable or Latch Enable is required to ensure valid data outputs.
M36P0R9070E0 2 Signal descriptions The Reset pin can be interfaced with 3V logic without any additional circuitry. It can be tied to VRPH (refer to Table 8., Flash Memory DC Characteristics - Voltages).
2.11 PSRAM Chip Enable input (EP)
The Chip Enable input activates the PSRAM when driven Low (asserted). When deasserted (VIH), the device is disabled, and goes automatically in low-power Standby mode or Deep Power-down mode.
2.12 PSRAM Write Enable (WP)
Write Enable, WP, controls the Bus Write operation of the PSRAM. When asserted (VIL), the device is in Write mode and Write operations can be performed either to the configuration registers or to the memory array.
2.13 PSRAM Output Enable (G P)
O utput Enable, GP, provides a high speed tri-state control, allowing fast read/write cycles to be achieved with the common I/O data bus.
2.14 PSRAM Upper Byte Enable (UBP)
The Upper Byte En-able, UBP, gates the data on the Upper Byte Data Inputs/Outputs (DQ8- DQ15) to or from the upper part of the selected address during a Write or Read operation.
2.15 PSRAM Lower Byte Enable (LBP)
The Lower Byte Enable, LBP, gates the data on the Lower Byte Data Inputs/Outputs (DQ0- DQ7) to or from the lower part of the selected address during a Write or Read operation. If both LBP and UBP are disabled (High) during an operation, the device will disable the data bus from receiving or transmitting data. Although the device will seem to be deselected, it remains in an active mode as long as EP remains Low.
2.16 PSRAM Configuration Register Enable (CRP)
When this signal is driven High, VIH, Write operations load either the value of the Refresh Configuration Register (RCR) or the Bus configuration register (BCR).
2.17 Deep Power-Down input (DPDF)
The Deep Power-Down input is used to place the device in a Deep Power-Down mode.When the device is in Deep Power-Down mode, the memory cannot be modified and data is protected. For further details on how the Deep Power-Down input signal works, please refer to the M58PR512J datasheet.
2.18 V DDF Supply Voltages
VDDF provides the power supply to the internal cores of the Flash memory. It is the main power supply for all Flash memory operations (Read, Program and Erase).
2.19 V CCP Supply Voltage
VCCP provides the power supply to the internal core of the PSRAM device. It is the main power supply for all PSRAM operations.
2.20 V DDQ Supply Voltage
VDDQ provides the power supply for the Flash memory and PSRAM I/O pins. This allows all Outputs to be powered independently of the Flash memory and SRAM core power supplies, V DDF and VCCP .
2.21 V PPF Program Supply Voltage
VPPF is both a control input and a power supply pin for the Flash memory. The two functions are selected by the voltage range applied to the pin. If VPPF is kept in a low voltage range (0V to VDDQ ) VPPF is seen as a control input. In this case a voltage lower than VPPLK gives an absolute protection against Program or Erase, while VPPF > VPP1 enables these functions (see Tables 7 and 8, Flash Memory DC Characteristics for the relevant values). VPPF is only sampled at the beginning of a Program or Erase; a change in its value after the operation has started does not have any effect and Program or Erase operations continue. If V PPF is in the range of VPPH it acts as a power supply pin. In this condition VPPF must be stable until the Program/Erase algorithm is completed.
M36P0R9070E0 2 Signal descriptions
2.22 V SS Ground
VSS is the common ground reference for all voltage measurements in the Flash (core and I/O Buffers) and PSRAM chips. It must be connected to the system ground. Note: Each Flash memory device in a system should have their supply voltage (VDDF ) and the program supply voltage VPPF decoupled with a 0.1µF ceramic capacitor close to the pin (high frequency, inherently low inductance capacitors should be as close as possible to the package). See Figure 4., AC Measurement Load Circuit. The PCB track widths should be sufficient to carry the required VPPF program and erase currents.
3 Functional description M36P0R9070E0
3 Functional description
Recommended operating conditions do not allow more than one device to be active at a time. other devices in the high impedance state when reading the selected device. Figure 2. Functional Block Diagram
512 Mbit
Table 3. Main Operating Modes
3 Depends on GF
M58PR512J datasheet for details. Flash memories must be disabled.
4 Maximum rating M36P0R9070E0
4 Maximum rating
other relevant quality documents. Table 4. Absolute Maximum Ratings
5 DC and AC parameters
Table 5. Operating and AC Measurement Conditions Figure 3. AC Measurement I/O Waveform
5 DC and AC parameters M36P0R9070E0
Figure 4. AC Measurement Load Circuit Table 6. Capacitance
- Sampled only, not 100% tested.
Table 7. Flash Memory DC Characteristics - Currents
8 Word 22 32 mA
16 Word 19 26 mA
8 Word 26 36 mA
16 Word 23 30 mA
- The DPD current is measured 40µs after entering the Deep Power Down mode.
- Sampled only, not 100% tested.
- V DDF Dual Operation current is the sum of read and program or erase currents.
Table 8. Flash Memory DC Characteristics - Voltages
Table 9. PSRAM DC Characteristics
- Input signals may overshoot to VDDQ + 1.0V for periods of less than 2ns during transitions.
- Output signals may undershoot to VSS – 1.0V for periods of less than 2ns during transitions.
- BCR5-BCR4 = 01 (default settings).
- This parameter is specified with all outputs disabled to avoid external loading effects. The user must add the current
required to drive output capacitance expected for the actual system.
- ISB maximum value is measured at +85°C with PAR set to Full Array. In order to achieve low standby current, all inputs
6 Package mechanical M36P0R9070E0
6 Package mechanical
The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. Figure 5. TFBGA107 8x11mm - 9x12 active ball array, 0.8mm pitch, package outline
Table 10. Stacked TFBGA107 8x11mm - 9x12 active ball array, 0.8mm pitch, package data
7 Part numbering M36P0R9070E0
7 Part numbering
Table 11. Ordering Information Scheme please contact the STMicroelectronics Sales Office nearest to you. ZAC= stacked TFBGA107 C stacked footprint.
8 Revision history
Table 12. Document revision history 28-Nov-2005 1 Initial release.
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners © 2005 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America