M24236 SENSATA | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 5

Technical content

Features

  • Hermetically Sealed (probe only)
  • Snap-action switching
  • Pre-set, non-adjustable calibration
  • High resistance to shock and vibration
  • Qualified to MIL-PRF-24236/2

www.sensata.com Page 2 Copyright © 2018 Sensata Technologies, Inc. Characteristics Contact Resistance 0.100 ohms per MIL-STD-202, Method 307 Contact resistance shown is for the 11041 (M1) thermostat and does not include resistance of wire leads or connector. Dielectric Strength

1250 VAC, rms, 60 cycles for 1 minute, terminal to case

1000 VAC, 60 cycles for 1 minute, terminal to terminal with contacts open per

MIL-STD-202, Method 301 Salt Spray Resistance Per MIL-STD-202, Method 101, Condition B, 5% Solution Ambient Temperature Range Maximum ambient exposure while in the closed position is 200°F above contact closing temperature. Operating Temperature Range -65°F to 550°F, (-53.9°C to 287.8°C) Operating Temperature Differential Tolerance °F °C °F °C ±°F ±°C -65 to - 1 -53.9 to -18.4 30 16.7 12 6.7 0 to 200 -17.8 to 93.3 20 11.1 7 3.9 201 to 300 93.9 to 148.9 30 16.7 10 5.6 301 to 450 149.5 to 223.2 40 22.2 14 7.8 451 to 550 223.8 to 287.8 70 38.9 30 16.7 * Tolerances based on precision factory calibration and test equipment. Customers checking tolerances should allow for differences in test equipment of ±1°F. Temperature settings outside the ranges indicated or to closer tolerances will be considered on special request. CONFIGURATIONS Standard 11041 (M1) probe packages are comprised of the following physical features, but many other variants are available. The standard material is stainless steel, but nickel plated brass versions are available. PLEASE NOTE: The orientation of the connector with respect to the package body is not controlled. Probe Body Thread Sizes Standard lengths are available in ½” increments from 1.5” to 6”. Termination Standard connector is a Sealtron B8002G-10SL-4P-F (or equivalent) Standard wire leads are AWG #18 stranded wire with white or black Teflon* insulation (per MIL-W-22759) (Teflon is a trademark of E. I. Dupont de Namers and Co.) Other Other styles are available, as well as custom designs 21542 ¾” - 16 thread/connector 21543 ½” pipe thread/leads 21548 ¾” - 16 thread/leads 21549 ½” pipe thread/connector 28303 (4344 thermostat) ½-14 PTF (SAE Short) Thread/brass body 28509 (4344 thermostat) M30 x 3.5 thread / spring loaded body Configuration Options Standard Part Numbers and Configurations Custom configurations are available Many other styles are available, including SPDT.

www.sensata.com Page 3 Copyright © 2018 Sensata Technologies, Inc. DIMENSIONS 21542 21548 21549 21543

www.sensata.com Page 4 Copyright © 2018 Sensata Technologies, Inc. DIMENSIONS (CONTINUED) 28303 28509 ORDERING OPTIONS Example : 21549-06-XXX-03 Basic Package Probe Length Operating Characteristics Wire Leads 21542 (or 21544, 21548, 21549) Basic package describes general physical appearance and basic thermostat incorporated into device Probe length times 2 (probe length is the length in inches from bottom of the hex to bottom of the device) Assigned consecutively (Sensata will assign this number at the time your order is taken) For wire leads, this is the length of wire in 6 inch increments (for 6” it would be 1, for 12” it would be 2, for 18” it would be 3, etc.). For connectors, contact Sensata Technologies for this code. 21549 06 XXX 03

Rev:10/05/18 www.sensata.com Copyright © 2018 Sensata Technologies, Inc. Sensata Technologies, Inc. (“Sensata”) data sheets are solely intended to assist designers (“Buyers”) who are developing systems that incorporate Sensata products (also referred to herein as “components”). Buyer understands and agrees that Buyer remains responsible for using its independent analysis, evaluation and judgment in designing Buyer’s systems and products. Sensata data sheets have been created using standard laboratory conditions and engineering practices. Sensata has not conducted any testing other than that specifically described in the published documentation for a particular data sheet. Sensata may make corrections, enhancements, improvements and other changes to its data sheets or components without notice. Buyers are authorized to use Sensata data sheets with the Sensata component(s) identified in each particular data sheet. HOWEVER, NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER SENSATA INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY THIRD PARTY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT, IS GRANTED HEREIN. SENSATA DATA SHEETS ARE PROVIDED “AS IS”. SENSATA MAKES NO WARRANTIES OR REPRESENTATIONS WITH REGARD TO THE DATA SHEETS OR USE OF THE DATA SHEETS, EXPRESS, IMPLIED OR STATUTORY , INCLUDING ACCURACY OR COMPLETENESS. SENSATA DISCLAIMS ANY WARRANTY OF TITLE AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY , FITNESS FOR A PARTICULAR PURPOSE, QUIET ENJOYMENT, QUIET POSSESSION, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS WITH REGARD TO SENSATA DATA SHEETS OR USE THEREOF. All products are sold subject to Sensata’s terms and conditions of sale supplied at www.sensata.com SENSATA ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR THE DESIGN OF BUYERS’ PRODUCTS. BUYER ACKNOWLEDGES AND AGREES THAT IT IS SOLELY RESPONSIBLE FOR COMPLIANCE WITH ALL LEGAL, REGULATORY AND SAFETY-RELATED REQUIREMENTS CONCERNING ITS PRODUCTS, AND ANY USE OF SENSATA COMPONENTS IN ITS APPLICATIONS, NOTWITHSTANDING ANY APPLICATIONS-RELATED INFORMATION OR SUPPORT THAT MAY BE PROVIDED BY SENSATA. Mailing Address: Sensata Technologies, Inc., 529 Pleasant Street, Attleboro, MA 02703, USA. Americas +1 (508)-236-3287 klixon@sensata.com AUTHORIZED DISTRIBUTORS Flame Enterprises Bob Correa, Director of Product Management +1 (240) 236-9802 bcorrea@flamecorp.com info@flamecorp.com | Web Tel: 1-800-854-2255 or 1-818- 700-2905 Fax: 1-818-407-5080 Peerless Electronics Steve Gunther, National Sales Manager +1 (516) 594-3509 sgunther@peerlesselectronics. com nysales@peerlesselectronics. com | Web Tel: 1-800-285-2121 Fax: 1-800-222-8096 Europe, Middle East & Africa Flame Enterprises Bob Correa, Director of Product Management +1 (240) 236-9802 bcorrea@flamecorp.com info@flamecorp.com | Web Tel: 1-800-854-2255 or 1-818- 700-2905 Fax: 1-818-407-5080 CONTACT US AGENCY APPROVALS & CERTIFICATIONS Max. Voltage Max. Current (Non-inductive) Max. Temp. Cycles Notes UL 120 VAC 2.5 A 450°F 100,000 Break but not make, ungrounded cup UL 110-300 VAC 720 VA 392°F 10,000 Make and break, ungrounded cup UL 300 VAC 360 VA 392°F 10,000 Make and break, grounded or ungrounded cup UL 24-240 VAC 120 VA 393°F 10,000 Make and break, grounded or ungrounded cup UL-C 120 VAC 2.5 A 450°F 100,000 UL/Canadian-UL Ratings For 28303 series only: UL and Canadian-UL (File #E34618) WARNINGS RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE

  • The product’s side panels may be hot, allow the product to cool before touching
  • Follow proper mounting instructions including torque values
  • Do not allow liquids or foreign objects to enter this product Failure to follow these instructions can result in serious injury, or equipment damage. HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
  • Disconnect all power before installing or working with this equipment
  • Verify all connections and replace all covers before turning on power Failure to follow these instructions will result in death or serious injury.