M1EXR-2-R/C03

M1EXR-2 MSYSTEM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 8

Technical content

MODEL: M1EXR-2 M1EXR-2 SPECIFICATIONS ES-5984 Rev.2 Page 1/8 https://www.m-system.co.jp/

2 Channel Super-mini Signal Conditioners

(2 channels, PC programmable) Functions & Features

• Accepts direct input from a RTD and provides a linearized process signal
• Wide selection of RTD
• 2 channels
• Adjustments with the front buttons
• Leadwire resistance compensation
• OEL display with good visibility Typical Applications
• Long distance transmission between the RTD and the transmitter 36 (1.42) (3.90) 125 (4.92) mm (inch) Note: The /f_igure shows the combination of the unit and the base. MODEL: M1EXR-2–[1][2]

ORDERING INFORMATION

• Code number: M1EXR-2-[1][2] Specify a code from below for each of [1] and [2]. (e.g. M1EXR-2-M2/Q)
• Specify the specification for option code /Q (e.g. /C01/SET) NO. OF CHANNELS 2: 2 channels INPUT – Field-selectable RTD JPt 100 (JIS'89), Pt 100 (JIS'89), Pt 100 (JIS'97, IEC), Pt 50Ω (JIS'81), Ni 508.4Ω, Pt 1000, Ni 100, Cu 10 @ 25℃ OUTPUT – Field-selectable ◆ DC Output
• Current output: 0 - 20 mA DC
• Voltage output: -5 - +5 V DC
• Voltage output: -10 - +10 V DC [1] POWER INPUT AC Power M2: 100 – 240 V AC (Operational voltage range 85 – 264 V, 47 – 66 Hz) DC Power R: 24 V DC (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) P: 110 V DC (Operational voltage range 85 – 150 V, ripple 10 %p-p max.) [2] OPTIONS blank: none /Q: With options (specify the specification) SPECIFICATIONS OF OPTION: Q (multiple selections) COATING (For the detail, refer to M-System's web site.) /C01: Silicone coating /C02: Polyurethane coating /C03: Rubber coating EX-FACTORY SETTING /SET: Preset according to the Ordering Information Sheet (No. ESU-5984)

RELATED PRODUCTS

• Installation base (model: M1E-BS2)
• M1E configurator software (model: M1ECFG) Downloadable at M-System’s web site. A dedicated cable is required to connect the module to the PC. Please refer to the internet software download site or the users manual (EM-5981) for the M1E configurator for applicable cable types. GENERAL SPECIFICATIONS Construction: Plug-in Connection
• Connected to base with connector
• Base M2.6 screw terminals (torque: 0.5 N·m) Applicable solderless terminal size (M3) Screw terminal: Nickel-plated steel Housing material: Flame-resistant resin (black) Isolation: Ch1.input to ch2.input to Ch1.output to ch2.output to power Overrange output: Approx. -10 to +110 % (Not available for

MODEL: M1EXR-2 M1EXR-2 SPECIFICATIONS ES-5984 Rev.2 Page 2/8 https://www.m-system.co.jp/ current output not greater than 0 mA) Input zero fine adj. range: -10 to +10℃ (front button) Input span fine adj. range: -10 to +10℃ (front button) Output zero fine adj. range: -5 to +5% (front button) Output span fine adj. range: 95 to 105% (front button) Burnout protection: Upscale standard; downscale or no burnout optional by programming Configuration: Program with front buttons or Via PC. Programmable features include: Refer to the parameter list. Configurator connection: 2.5 dia. miniature jack; RS-232-C level ■Recommended solderless terminal size - M3 (unit: mm) 12max 6max 3max 4min 3.2 dia. (mm) DISPLAY Display functions: Displays and sets measured range, engineering unit Number of pixels: 68 × 95 (horizontal × vertical) Character color: Yellow Display life: Approx. 50000 hours (Expected time for the Display brightness to be reduced to 50 % when the Display is used continuously with brightness setting 2 in 25 ℃) Display type: OEL display Display digit: Negative 5 digits, positive 6 digits (-99999 to 999999) Decimal point position: None, number of decimal places 1 or INPUT SPECIFICATIONS Input: 2- or 3-wire RTD Maximum leadwire resistance: 50 Ω per wire (For Cu 10, 20 Ω per wire) Sensing current: Pt 100, JPt 100, Pt 50 Ω, Ni 100, Cu 10: approx. 1.0 mA Pt 1000, Ni 508.4 Ω: approx. 0.2 mA Measurement rang: -5 to +105% of input setting value Refer to the operating manual (EM-5984-B) for changing input range, setting value. OUTPUT SPECIFICATIONS ■ DC Current Output range: 0 – 20 mA DC Conformance range: 0 – 22mA DC Minimum span: 1 mA Load resistance: Output drive 15 V max. (e.g. 4 – 20 mA: 750 Ω [15 V ÷ 20 mA]) (Not available to output less than 0 mA, output range may not be extended to -5 %) ■ DC Voltage Output range: -5 - +5 V DC, -10 - +10 V DC Conformance range: -6 - +6 V DC, -12 - +12 V DC Minimum span: 250 mV, 1 V Load resistance: 200 kΩ min. INSTALLATION Power Consumption

• AC: ≤ 7 VA at 100 V ≤ 10 VA at 200 V ≤ 12 VA at 264 V
• DC: ≤ 4 W Operating temperature: -5 to +55°C (23 to 131°F) Storage temperature: -5 to +55°C (23 to 131°F) Operating humidity: 10 to 85 %RH (non-condensing) Mounting: Surface or DIN rail Weight: 120 g (0.26 lb) except base PERFORMANCE Accuracy: Input accuracy + output accuracy See CALCULATION EXAMPLES OF OVERALL ACCURACY. Inversely proportional to the setting span. Input accuracy: (whichever is greater) Table 1 accuracy value or ±0.1 % of FS Display accuracy: Input display: Input accuracy ±1 digit Output display: Input accuracy + output accuracy ±1 digit Output accuracy: (% of max. output range) 0 - 20 mA: ±0.06 % -5 - +5 V: ±0.03 % Temp. coefficient (% of max. I/O range): ±0.015 %/°C (±0.008 %/°F) Response time (filter time constant: 0 sec.): ≤ 0.5 sec. (0 – 90 %) Burnout response: ≤ 10 sec. Line voltage effect: ±0.1 % over voltage range Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 1500 V AC @ 1 minute (Ch1 input to Ch2 input to Ch1 output to Ch2 output to power to ground)

MODEL: M1EXR-2 M1EXR-2 SPECIFICATIONS ES-5984 Rev.2 Page 3/8 https://www.m-system.co.jp/ CALCULATION EXAMPLES OF OVERALL ACCURACY [Example] Input Range Pt 100 (JIS'97, IEC), 0 – 100°C, Output Range 0 – 20 mA, Output Setting 4 – 20 mA ■ Overall accuracy

• Input Accuracy 0.2 ℃ is higher thus 0.2 ℃ is selected
• Output Accuracy = Output Range Span (20 mA) ÷ Output Span Setting (16 mA) × 0.06 % = 0.075 % Overall Accuracy = 0.2 + 0.075 = ±0.275 % [Table 1] INPUT RANGE °C MINIMUM SPAN SETTING RANGE ACCURACY Pt 50 Ω (JIS’ 81) 20 -200.00 to +649.00 ±0.8 Ni 508.4 Ω 20 -50.00 to +200.00 ±0.8 Pt 1000 20 -200.00 to +850.00 ±0.8 Ni 100 20 -50.00 to +200.00 ±0.8 Cu 10 @ 25°C 20 -50.00 to +250.00 ±1 .0 INPUT RANGE °F MINIMUM SPAN SETTING RANGE ACCURACY Pt 50 Ω (JIS’ 81) 36 -328.00 to +1200.20 ±1 .44 Ni 508.4 Ω 36 -58.00 to +392.00 ±1 .44 Pt 1000 36 -328.00 to +1562.00 ±1 .44 Ni 100 36 -58.00 to +392.00 ±1 .44 Cu 10 @ 25°C 36 -58.00 to +482.00 ±1 .80 INPUT RANGE K MINIMUM SPAN SETTING RANGE ACCURACY Pt 50 Ω (JIS’ 81) 20 73.15 to 922.15 ±0.8 Ni 508.4 Ω 20 223.15 to 473.15 ±0.8 Pt 1000 20 73.15 to 1123.15 ±0.8 Ni 100 20 223.15 to 473.15 ±0.8 Cu 10 @ 25°C 20 223.15 to 523.15 ±1 .0 STANDARDS & APPROVALS EU conformity: EMC Directive EMI EN 61000-6-4 EMS EN 61000-6-2 Low Voltage Directive EN 61010-1 Installation Category II Pollution Degree 2 Input or output to power: Reinforced insulation (300 V) RoHS Directive

MODEL: M1EXR-2 M1EXR-2 SPECIFICATIONS ES-5984 Rev.2 Page 4/8 https://www.m-system.co.jp/ EXTERNAL VIEW Mode Button Set Button Display Configurator Jack Up Button Down Button COMPONENT FUNCTION Display Indicates present values, setting values and abnormal information. Two types of present values are displayed respectively at the upper and lower parts according to setting. Mode button Shifts from Measuring mode to each setting mode. The destination changes depending on how long the button is held down. Pressing Mode button for ≥ 2 seconds returns to Measuring mode from each setting mode.. Set button Shifts the setting value of each setting parameter item to a setting changeable state. When at setting changeable state, used to move through the digits of setting value and to enter (save) the setting value. Up button Shifts through setting parameter items and to increase or select the setting value. Down button Shifts through setting parameter items and to decrease or select the setting value. Con/f_i gurator Jack Used to perform con/f_i guration with M1E con/f_i gurator software (model: M1ECFG). When using the software, set the Lockout setting of the unit to ‘Lock’ . Refer to the operating manual (EM-5984-B) for detailed procedures. TERMINAL ASSIGNMENTS 6 7 2 3 4 8 9 16 17 12 13 14 18 19 No. FUNCTION No. FUNCTION

1 Unused 11 Ch1 Output +

2 Unused 12 Ch1 Output –

3 Ch1 Input A 13 Unused

4 Ch1 Input B (3-wire) 14 Ch2 Output +

5 Ch1 Input B 15 Ch2 Output –

6 Unused 16 Unused

7 Unused 17 Unused

8 Ch2 Input A 18 Unused

9 Ch2 Input B (3-wire) 19 Power U (+)

10 Ch2 Input B 20 Power V (–)

• Base does not come with the unit. Please order separately.

MODEL: M1EXR-2 M1EXR-2 SPECIFICATIONS ES-5984 Rev.2 Page 5/8 https://www.m-system.co.jp/ PARAMETER LIST It is available to con/f_i gure or con/f_i rm settings shown below by using front button. Con/f_i guring or con/f_i rming with PC is available when using M1E con/f_i gurator software (model: M1ECFG). MODE ITEM SETTING PARAMETER RANGE UNIT INITIAL VALUE Ch1 setting 01 Lockout setting Lock / Unlock — Lock

09 Ch1 Temperature unit °C / °F / K — °C

11 Ch1 Input range JPt 100 (JIS ’89)

Pt 100 (JIS ’89) Pt 100 (JIS ’97 , IEC) Pt 50 Ω (JIS ’81) Ni 508.4 Ω Pt 1000 Ni 100 Cu 10 @ 25°C — Pt 100 (JIS ’97 , IEC) 12 Ch1 0 % input setting JPt 100 (JIS ’89) : -200.00 – 480.00 Pt 100 (JIS ’89) : -200.00 – 630.00 Pt 100 (JIS ’97 , IEC) : -200.00 – 830.00 Pt 50 Ω (JIS ’81) : -200.00 – 629.00 Ni 508.4 Ω : -50.00 – 180.00 Pt 1000 : -200.00 – 830.00 Ni 100 : -50.00 – 180.00 Cu 10 @ 25°C : -50.00 – 230.00 °C 0.0 13 Ch1 100 % input setting JPt 100 (JIS ’89) : -180.00 – 500.00 Pt 100 (JIS ’89) : -180.00 – 650.00 Pt 100 (JIS ’97 , IEC) : -180.00 – 850.00 Pt 50 Ω (JIS ’81) : -180.00 – 649.00 Ni 508.4 Ω : -30.00 – 200.00 Pt 1000 : -180.00 – 850.00 Ni 100 : -30.00 – 200.00 Cu 10 @ 25°C : -30.00 – 250.00 °C 100.0

16 Ch1 Input decimal point No decimal point

The number of decimal places : 1 or 2 — 1 place of decimals

18 Ch1 Output range 0 – 20 mA

-5 – +5 V -10 – +10 V — 0 – 20 mA 19 Ch1 0 % output setting 0.000 – 19.000 -5.000 – 4.750 -10.000 – 9.000 mA V V 4.000 20 Ch1 100 % output setting 1 .000 – 20.000 -4.750 – 5.000 -9.000 – 10.000 mA V V 20.000

74 Ch1 Burnout None / Down / Up — Up

75 Ch1 Sensor wires 2 Wires / 3 Wires — 3 Wires

76 Ch1 Wire resistance 0.000 – 50.000 * Ω 0.000 79 Ch1 Filter time constant 0 – 30 Sec. 0 80 Ch1 Input zero /f_i ne adjust -10.00 – 10.00 * °C 0.00 81 Ch1 Input span /f_i ne adjust -10.00 – 10.00 * °C 0.00 82 Ch1 Output zero /f_i ne adjust -5.000 – 5.000 % 0.000 83 Ch1 Output span /f_i ne adjust 95.000 – 105.000 % 100.000 89 Ch1 Loop test -10.00 – 110.00 % Cancel

MODEL: M1EXR-2 M1EXR-2 SPECIFICATIONS ES-5984 Rev.2 Page 6/8 https://www.m-system.co.jp/ MODE ITEM SETTING PARAMETER RANGE UNIT INITIAL VALUE Ch2 setting 109 Ch2 Temperature unit °C / °F / K — °C

111 Ch2 Input range JPt 100 (JIS ’89)

Pt 100 (JIS ’89) Pt 100 (JIS ’97 , IEC) Pt 50 Ω (JIS ’81) Ni 508.4 Ω Pt 1000 Ni 100 Cu 10 @ 25°C — Pt 100 (JIS ’97 , IEC) 112 Ch2 0 % input setting JPt 100 (JIS ’89) : -200.00 – 480.00 Pt 100 (JIS ’89) : -200.00 – 630.00 Pt 100 (JIS ’97 , IEC) : -200.00 – 830.00 Pt 50 Ω (JIS ’81) : -200.00 – 629.00 Ni 508.4 Ω : -50.00 – 180.00 Pt 1000 : -200.00 – 830.00 Ni 100 : -50.00 – 180.00 Cu 10 @ 25°C : -50.00 – 230.00 °C 0.0 113 Ch2 100 % input setting JPt 100 (JIS ’89) : -180.00 – 500.00 Pt 100 (JIS ’89) : -180.00 – 650.00 Pt 100 (JIS ’97 , IEC) : -180.00 – 850.00 Pt 50 Ω (JIS ’81) : -180.00 – 649.00 Ni 508.4 Ω : -30.00 – 200.00 Pt 1000 : -180.00 – 850.00 Ni 100 : -30.00 – 200.00 Cu 10 @ 25°C : -30.00 – 250.00 °C 100.0

116 Ch2 Input decimal point No decimal point

The number of decimal places : 1 or 2 — 1 place of decimals

118 Ch2 Output range 0 – 20 mA

-5 – +5 V -10 – +10 V — 0 – 20 mA 119 Ch2 0 % output setting 0.000 – 19.000 -5.000 – 4.750 -10.000 – 9.000 mA V V 4.000 120 Ch2 100 % output setting 1 .000 – 20.000 -4.750 – 5.000 -9.000 – 10.000 mA V V 20.000

174 Ch2 Burnout None / Down / Up — Up

175 Ch2 Sensor wires 2 Wires / 3 Wires — 3 Wires

176 Ch2 Wire resistance 0.000 – 50.000 * Ω 0.000 179 Ch2 Filter time constant 0 – 30 Sec. 0 180 Ch2 Input zero /f_i ne adjust -10.00 – 10.00 * °C 0.00 181 Ch2 Input span /f_i ne adjust -10.00 – 10.00 * °C 0.00 182 Ch2 Output zero /f_i ne adjust -5.000 – 5.000 % 0.000 183 Ch2 Output span /f_i ne adjust 95.000 – 105.000 % 100.000 189 Ch2 Loop test -10.00 – 110.00 % Cancel

01 Lockout setting Lock / Unlock — Lock

Advanced 201 Display setting Upper: choose from 8 types * Lower: choose from 9 types* — Upper: Ch1 INPUT Lower: Ch2 INPUT

202 Channel enable Choose from 3 types * — Ch1 enable

203 Brightness 1 (darkest) – 4 (brightest) — 4

204 Display timeout 0 (always on), 1 – 60 min. 10

205 Reset all settings OFF / RESET — OFF

206 Version indication — — —

• For detailed types, refer to the operating manual (EM-5984-B).

MODEL: M1EXR-2 M1EXR-2 SPECIFICATIONS ES-5984 Rev.2 Page 7/8 https://www.m-system.co.jp/ EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch] 125 (4.92) 36 (1 .42) DIN RAIL 35mm wide 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 * Base does not come with the unit. Please order separately. MOUNTING REQUIREMENTS unit: mm [inch] 99 (3.90) 2–M4 SCREW * Mounting requirements for base.

MODEL: M1EXR-2 M1EXR-2 SPECIFICATIONS ES-5984 Rev.2 Page 8/8 https://www.m-system.co.jp/ SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Digital Computation Circuit JACK A B A B B A B A B B Low Drift Amplifie & Burnout Low Drift Amplifie & Burnout CONFIGURATOR CH1 RTD 2-wire 3-wire CH2 RTD 2-wire 3-wire Isolation Isolation Front Button Display Circuit Isolation Isolation Base U(+) V(–) POWER CH1 OUTPUT CH2 OUTPUT Output Driver Output Driver Specifications are subject to change without notice.