M18T_V01 BANNER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

18 mm Sensor with Discrete Output and TEACH Configuration To view or download the latest technical information about this product, including specifications, dimensions, accessories, and wiring, see www.bannerengineering.com.

  • Fast 25 ms response time with up to 20 Hz switching speed
  • Easy-to-use TEACH configuration without potentiometer adjustments
  • Small, self-contained package; no auxiliary controller needed
  • Rugged encapsulated design for harsh environments
  • Choice of 2 meter or 9 meter unterminated cable, or 5-pin M12/Euro-style quick disconnect
  • Product motion not required for sensing
  • Remote configuration available in both Static and Dynamic modes WARNING: Not To Be Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. AVERTISSEMENT: A ne pas utiliser en guise de protection individuelle Ce produit ne doit pas être utilisé en tant que système de détection destiné à la protection individuelle. Une utilisation dans de telles conditions pourrait entraîner des dommages corporels graves, voire mortels.</b> Ce produit n'est pas équipé du circuit redondant d'autodiagnostic nécessaire pour être utilisé dans des applications de protection personnelle. Une panne du capteur ou un mauvais fonctionnement peut entraîner l'activation ou la désactivation de la sortie. Models Model Connection 1 D:S Ratio Sensing Face Supply Voltage Output M18TB8 2 m (6.5 ft) unterminated 5-wire shielded cable 8:1 Integrated lens 10 to 30 V dc Bipolar (NPN and PNP) M18TB8Q Integral 5-pin M12/Euro-style quick disconnect M18TB6E 2 m (6.5 ft) unterminated 5-wire shielded cable 6:1 Enclosed plastic face (for food industry use)M18TB6EQ Integral 5-pin M12/Euro-style quick disconnect M18TB14 2 m (6.5 ft) unterminated 5-wire shielded cable 14:1 Germanium lens M18TB14Q Integral 5-pin M12/Euro-style quick disconnect 1 To order the 9 m (30 ft) PVC cable model, add the suffix "W/30" to the cabled model number. For example, M18TB8 W/30. Models with a quick disconnect require a mating cordset. T-GAGE® M18T Series Sensor Original Document 120632 Rev. D

6 February 2019

than the ambient condition and then activate an output. infrared energy within its field of view (see Figure 2 on page 3).

  • Hot part detection (baked goods, metals, bottles)
  • Ejection verification of injection-molded parts
  • Flame process verification
  • Hot glue detection (packaging equipment, book binding)
  • Cold part detection (frozen foods, ice, dairy)
  • Roller monitoring

Figure 1. Sensor Features cadre de sécurité pour la détection de feu. Sensing range is determined by the sensor’s field of view or viewing angle, combined with the size of the object(s) being detected.

Figure 2. Detection spot size versus distance from sensor unintended thermal energy into the sensor’s field of view. See Application Note on page 7. should completely fill the sensor field of view. In some applications, when the object is too small, this may not be possible. In such cases, if the object is hot enough, the thermal contrast may still be adequate to trigger the sensor output. Additional Accessories on page 8.

  • Two-Point Static TEACH
  • Dynamic TEACH Use the push button or remote input to configure the sensor. Note: The duration of each remote line pulse (corresponding to a push button “click”), and the period between multiple pulses, are defined as “T”: 0.04 seconds < T < 0.8 seconds. T-GAGE® M18T Series Sensor P/N 120632 Rev. D www.bannerengineering.com - Tel: + 1 888 373 6767 3

digital output on PLC. Perform the procedure below to enable or disable the push button. Remote Input3 Pulse the remote line 4-times. depending on the previous condition. configured conditions, with the Output ON condition on one side and the Output OFF condition on the other. second condition is configured. Figure 3. 2-Point Static TEACH

  1. Access 2-Point Static TEACH configuration.
  • Output LED turns Amber Remote Input2 No action required. 2. Present the output ON condition. Method Action Result Push Button Press the button 1-time.
  • Output LED turns OFF Remote Input Pulse the remote line 1-time. T 2 0.04 sec < T < 0.8 sec T-GAGE® M18T Series Sensor 4 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 120632 Rev. D
  1. Present the output OFF condition. Method Action Result Push Button Press the button 1-time. TEACH Accepted
  • Power LED turns Green
  • The sensor configures switching threshold and returns to Run mode 2-Point Static TEACH Not Accepted The sensor returns to the beginning of the TEACH configuration. Remote Input Pulse the remote line 1-time. T Note: To exit 2-Point Static TEACH configuration without saving a configuration, press and hold the push button for 2 seconds or hold the remote line for 2 seconds. The sensor will return to Run mode without saving a configuration. Dynamic TEACH Use Dynamic TEACH configuration method for applications where both the ON and OFF target conditions can not be presented to the sensor dynamically by the operator. After the configuration has been completed, the threshold at the midpoint is optimized by the sensor halfway between the average signals presented during the Dynamic TEACH configuration. 1. Access Dynamic TEACH configuration. Method Action Result Push Button Press and hold the button for 2 seconds. • Power LED turns Red
  • Output LED turns Amber Remote Input3 No action required. 2. Present the sensing conditions. Method Action Result Push Button Press the button 2-times.
  • Sensor begins Dynamic TEACH configuration
  • Output LED flashes Amber at 2 HzRemote Input Pulse the remote line 2-times. T T T 3. End Dynamic TEACH configuration. Method Action Result Push Button Press the button 1-time. • The sensor ends data collection; configures the threshold
  • Power LED turns Green
  • The sensor returns to Run mode Remote Input Pulse the remote line 1-time. T Hot Operate/Cold Operate Select Configure the sensor for Hot Operate, or Cold Operate using the remote input wire (gray). Pulse the remote line three times to toggle between Hot and Cold Operate. 3 (0.04 sec < T < 0.8 sec) T-GAGE® M18T Series Sensor P/N 120632 Rev. D www.bannerengineering.com - Tel: + 1 888 373 6767 5

Remote Input3 Pulse the remote line 3-times. T T T T T Hot Operate or Cold Operate is selected, depending on the previous condition. Specifications Temperature Measurement Range Custom ranges available upon request Sensing Range Depends on object size and sensing field of view (see Sensing Field of View on page 2) Wavelength 8 µm to 14 µm Distance to Spot Size (D:S) Ratio 6:1, 8:1, or 14:1, depending on model Supply Voltage

10 V dc to 30 V dc (10% maximum ripple)

35 mA maximum (exclusive of load) Output Configuration One NPN and one PNP in each model Output Protection Protected against short-circuit conditions Output Ratings 100 mA maximum (each output) OFF-state leakage current: NPN < 200 microamps; PNP < 10 microamps NPN saturation: < 200 mV at 10 mA and < 1 V at 100 mA PNP saturation: < 1.2 V at 10 mA and < 1.6 V at 100 mA Delay at Power-Up 1.5 seconds Output Response Time 25 ms Repeatability (Relative) 1 °C Minimum Taught Differential 3 °C Hysteresis 5% of taught differential (minimum 1 °C) Adjustments TEACH configuration Indicators One bicolor (Green/Red) status LED, one Amber LED (see Indicators on page 2) Remote Teach Input Impedance: 3 kΩ Construction Threaded Barrel: 304 stainless steel Push Button Housing: ABS/PC Push Button: Santoprene Lightpipes: Acrylic Operating Conditions Environmental Rating Leakproof design rated IEC IP67; NEMA 6 Temperature Warm-Up Time 5 minutes Certifications Class 2 power Required Overcurrent Protection WARNING: Electrical connections must be made by qualified personnel in accordance with local and national electrical codes and regulations. Overcurrent protection is required to be provided by end product application per the supplied table. Overcurrent protection may be provided with external fusing or via Current Limiting, Class 2 Power Supply. Supply wiring leads < 24 AWG shall not be spliced. For additional product support, go to www.bannerengineering.com. Supply Wiring (AWG) Required Overcurrent Protection (Amps) 20 5.0 22 3.0 24 2.0 26 1.0 28 0.8 30 0.5 Protection contre la surintensité requise AVERTISSEMENT: Les raccordements électriques doivent être effectués par du personnel qualifié conformément aux réglementations et codes électriques nationaux et locaux. Une protection de surintensité doit être fournie par l'installation du produit final, conformément au tableau fourni. Vous pouvez utiliser un fusible externe ou la limitation de courant pour offrir une protection contre la surtension dans le cas d'une source d'alimentation de classe 2. Les fils d'alimentation < 24 AWG ne peuvent pas être raccordés. Pour obtenir un support produit supplémentaire, rendez-vous sur le site www.bannerengineering.com. Câblage d'alimentation (AWG) Protection contre la surtension requise (ampères) 20 5.0 22 3.0 24 2.0 26 1.0 28 0.8 30 0.5 T-GAGE® M18T Series Sensor 6 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 120632 Rev. D

The following are examples of materials with high and low emissivity. Additional examples can be found online. Sensor-Friendly Materials (High Emissivity) Materials to Sense with Caution (Low Emissivity)

  • Aluminum - anodized
  • Asphalt
  • Brick
  • Carbon - lampblack or plate material
  • Cardboard - corrugated or chipboard
  • Concrete
  • Glass - smooth, lead, or borosilicate (e.g., Pyrex®)
  • Gypsum (including finished boards)
  • Ice
  • Iron and steel (except bright galvanized)
  • Paper - most types, regardless of color
  • Styrofoam ® insulation
  • Plastics
  • Water
  • Wood - most types
  • Aluminum - plain or highly polished
  • Copper
  • Galvanized iron
  • Stainless steel
  • Vapor-deposited materials Dimensions Cabled Models Quick Disconnect Models 26.5 mm (1.04") See table below** See table below*27 mm (1.06") 18.0 mm (0.71") 10.6 mm (0.42") 6.0 mm (0.24") **Overall Length Model M18T..8Q 91.3 mm (3.59") Model M18T..6EQ 91.8 mm (3.61") Model M18T..14Q 96.6 mm (3.80") *Overall Length Model M18T..8 81.2 mm (3.20") Model M18T..6E 81.7 mm (3.22") Model M18T..14 86.5 mm (3.41") M18 X 1 Accessories Cordsets 5-Pin Threaded M12/Euro-Style Cordsets—with Shield Model Length Style Dimensions Pinout (Female) MQDEC2-506 1.83 m (6 ft) Straight 44 Typ. ø 14.5 M12 x 1 1 = Brown 2 = White 3 = Blue 4 = Black 5 = Gray MQDEC2-515 4.57 m (15 ft) MQDEC2-530 9.14 m (30 ft) MQDEC2-550 15.2 m (50 ft) MQDEC2-506RA 1.83 m (6 ft) Right-Angle 32 Typ.[1.26"] 30 Typ.[1.18"] ø 14.5 [0.57"] M12 x 1 MQDEC2-515RA 4.57 m (15 ft) MQDEC2-530RA 9.14 m (30 ft) MQDEC2-550RA 15.2 m (50 ft) T-GAGE® M18T Series Sensor P/N 120632 Rev. D www.bannerengineering.com - Tel: + 1 888 373 6767 7
  • Right-angle mounting bracket with a curved slot for versatile orientation
  • 12-ga. stainless steel
  • 18 mm sensor mounting hole
  • Clearance for M4 (#8) hardware A B C Hole center spacing: A to B = 24.2 Hole size: A = ø 4.6, B = 17.0 × 4.6, C = ø 18.5 SMB18SF
  • 18 mm swivel bracket with M18 × 1 internal thread
  • Black thermoplastic polyester
  • Stainless steel swivel locking hardware included B A Hole center spacing: A = 36.0 Hole size: A = ø 5.3, B = ø 18.0 SMB18UR
  • 2-piece universal swivel bracket
  • 300 series stainless steel
  • Stainless steel swivel locking hardware included
  • Mounting hole for 18 mm sensor 137 64 42 B A C Hole center spacing: A = 25.4, B = 46.7 Hole size: B = 6.9 × 32.0, C = ø 18.3 Additional Accessories Laser Alignment Tool - LAT1812
  • Enables easy sensor alignment at long distances.
  • Kit includes one SMB1812 bracket and M12 laser emitter.
  • Thread bracket housing onto barrel of mounted sensor; M12 laser emitter inserted into housing provides a precise laser spot for aiming temperature sensor. (Refer to Banner data sheet p/n 122529 for more information.)
  • Remove laser emitter before using sensor. SMB1812 Bracket M12 Laser Emitter Shown with T-GAGE M18T attached Banner Engineering Corp. Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com. For patent information, see www.bannerengineering.com/patents. T-GAGE® M18T Series Sensor © Banner Engineering Corp. All rights reserved