M12 BANNER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

IEC Class 1 Laser for Use with Banner Modulated Receivers

  • A low-power device emitting a visible red beam, 650 nm wavelength
  • Beam is bore-sighted to within 2 milliradians and 0.25 mm of the housing centerline
  • Collimated, apertured beam is 2 mm diameter with divergence of less than 1 milliradian
  • Compatible with a variety of Banner modulated photoelectric receivers
  • Useful for medium-range sensing, or for sensing very small objects or profiles; excellent mechanical repeatability in position-sensing applications
  • Smooth-barrel aluminum housing is suitable for a precision mount
  • Available with unterminated, 2 m (6.5 ft) cable or 150 mm (6 in) quick-disconnect cable
  • Modulated beam (33 kHz, 25% duty cycle)
  • 57 mm (2.25 in) long overall
  • 10 V dc to 30 V dc operation WARNING: Not To Be Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. CAUTION: Never stare directly into the sensor lens. Laser light can damage your eyes. Avoid placing any mirror-like object in the beam. Never use a mirror as a retroreflective target. CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Do not attempt to disassemble this sensor for repair. A defective unit must be returned to the manufacturer. Models Model Range Connector1 Supply Voltage Effective Beam at Receiver at 25° C M126E1LD Range varies, depending on which receiver is used (see Excess Gain on page 4) 2 m (6.5 ft) unterminated

10 V dc to 30 V dc

Opposed Distance Beam Width 1.5 m (5 ft) 3.5 mm (0.14 in) 3 m (10 ft) 5 mm (0.2 in) 6 m (20 ft) 8 mm (0.3 in) 15 m (50 ft) 17 mm (0.7 in) 30 m (100 ft) 32 mm (1.3 in) M126E1LDQ 150 mm (6 in) PVC cable with 3-wire Pico-style quick disconnect Installation Mounting Mounting suggestions:

  • To take advantage of the bore-sight beam placement offered by the M12 laser emitter, use a two-part clamp mount or a mounting block with a precision-drilled hole. Allow minimum clearance for the 12.7 mm (0.50 in) diameter housing, maximum diameter 12.83 mm (0.505 in).
  • Clamp on both sides of the label. Do not clamp only on the labeled area. Use only plastic-tipped screws or set screws – not metal – to avoid compression of the housing. Mounting bracket assembly model SMB46X3 is recommended for use with the M12. The assembly includes: 1 To order the 9 m (30 ft) PVC cable model, replace the suffix "Q" with "W/30" in the model number. For example, M126E1LDQ W/30. Models with a quick disconnect require a mating cordset. M12 Class 1 Laser Emitter Original Document 53808 Rev. C

25 October 2017

Supply Voltage and Current 10 V dc to 30 V dc (10% max. ripple) at less than 30 mA Supply Protection Circuitry Protected against reverse polarity, transient voltages, and electrostatic discharge Delay at Power-Up Less than 30 milliseconds Sensing Beam Visible red Class 1 laser, 650 nm (temperature coefficient 0.2 nm/°C) Pulse Width: 7 µs Rep Rate: 30 µs Peak Output Power: 0.36 milliwatts Beam Diameter at Aperture Approximately 2 mm (0.08 in) diameter Beam Placement Within 0.25 mm (0.01 in) and ±2 milliradians of mechanical centerline axis of housing Beam Divergence ± 0.5 milliradians typical at 25° C; ±1.0 milliradians at operating temperature extremes Laser Classification Class 1 laser product; complies with 21 CFR 1040.10, EN 60825-1:2001 except for deviations pursuant to laser notice No. 50, dated 7-26-01 Laser Control Beam enable: Apply + 10 V dc to 30 V dc to black wire Beam inhibit: Apply 0 V or by opening circuit Enable delay: Less than 30 milliseconds Inhibit delay: Less than 1 milliseconds Indicators Indicators are visible through the rear cover Green indicates power applied Amber indicates laser enabled Connections 2 m (6.5 ft) unterminated 3-wire PVC-jacketed high-flex cable, 9 m (30 ft) unterminated 3-wire PVC-jacketed high-flex cable, or 150 mm (6 in) PVC cable with a 3-pin M8/Pico-style male quick disconnect (QD) Construction 12.7 mm (0.50 in) dimeter smooth aluminum barrel; black hard-coat anodized finish MIL-A-8625 Type III, Class II Operating Temperature 90% at +40 °C maximum relative humidity (non-condensing) Environmental Rating NEMA 6; IEC IP67 Certifications Product Label Dimensions All measurements are listed in millimeters [inches], unless noted otherwise. 57 mm (2.25") Green LED Indicates power applied Amber LED Indicates laser enabled See "Connections" in Specifications ø12.7 mm (0.50") Aperture/Caution Label (Do not clamp only in this area) DO NOT ST INTO BEA Peak Power: 2.2mW, 0.3633kHz 25% duty cycle LASER RADIA Excess Gain The Excess Gain of the M12 emitter is dependent on the particular receiver used. The following is a comparison of the excess gain for various recommended receivers at 15 m (50 ft). M12 Class 1 Laser Emitter 4 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 53808 Rev. C

Receiver Excess Gain at 15 m (50 ft) MULTI-BEAM SBRX1 1,900 SBR1 1,900 SBRXD1 1,900 SBRD1 1,900 MAXI-BEAM RSBR 1,400 RSBRSR 150 VALUE-BEAM SMW95R 3,400 SMI91RQD 1,800 EZ-BEAM T18SN6R 750 T30SN6R 750 S12SN6R 750 Receiver Excess Gain at 15 m (50 ft) MINI-BEAM SM31R 250 SM31RL 1,700 SM31RMHS 180 SM31RLMHS 1,100 ECONO-BEAM SE61R 60 SE61RMHS 50 Others SM51RB 120 Q23SN6R 40 Q10AN6R 25 Q45BB6R 900 For information on compatibility of the M12 emitter with other Banner photoelectric receivers contact Banner Engineering. Accessories Mounting Brackets SMB46X3

  • Assembly with mounting block and adjustable bracket
  • Includes: 2 mm Shortarm hex key 3/64-in Shortarm hex key

4 Set screws

Ø6.6

36 SMB127

  • Mounting block only
  • Includes: 3/64-in Shortarm hex key

Ø12.93 X 36 36 Quick-Disconnect Cables 3-Pin Threaded M8/Pico-Style Cordsets Model Length Style Dimensions Pinout (Female) PKG3M-2 2 m (6.56 ft) Straight ø 9.5 35 Typ. M8 x 1 3 1 1 = Brown 3 = Blue 4 = Black PKG3M-5 5 m (16.40 ft) PKG3M-7 7 m (22.97 ft) PKG3M-9 9 m (29.53 ft) PKG3M-10 10 m (32.81 ft) M12 Class 1 Laser Emitter P/N 53808 Rev. C www.bannerengineering.com - Tel: +1-763-544-3164 5

Model Reflectivity Factor Maximum Temperature Size BRT-THG-4X4-5 0.7 +60 °C (+140 °F) 100 × 100 mm (package of 5) Model Reflectivity Factor Maximum Temperature Size BRT-THG-8.5X11-2 0.7 +60 °C (+140 °F) 216 × 280 mm (package of 2) Model Reflectivity Factor Maximum Temperature Size BRT-THG-18X36 0.7 +60 °C (+140 °F) 457 × 914 mm (single sheet) Banner Engineering Corp. Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com. M12 Class 1 Laser Emitter © Banner Engineering Corp. All rights reserved