LTUPC455GB RAKON | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 4

Technical content

Ceramic Filter | FM broadcast receiver Part number: LTUPC455GB 2.832.217h | Revision: A1 | Date: 26 January 2023 Specifications are subject to change without notice Copyright © 2016 to 2023 Rakon Limited. All rights reserved Page 1 of 4 www.rakonxpress.com

1.0 About Maximum Rating1

N° Characteristics Min. Max. Unit

1.1 Withstanding Voltage 50 VDC

1.2 Ambient Operating Temperature Range -20 80 °C

1.3 Lead Temperature for Soldering 1/16” from Body for 10sec 260 °C

1.4 Storage Temperature Range -40 85 °C

1.5 Power Dissipation (Ta = 25°C) 100 mW

1.6 Isolation Resistance 100 MΩ

2.0 Electrical Characterstics (Ta = 25°C)

N° Characteristics Min. Nom. Max. Unit

2.1 Center Frequency (fc) NS 455 NS kHz

2.2 Initial Tolerance ±1.5 kHz 2.3 6 dB bandwidth ±4.5 kHz 2.4 Selectivity (50 dB) ±10.0 kHz 2.5 Insertion Loss (IL) 6.0 dB 2.6 Ripple in Pass band 2.0 dB

2.7 Stop Band Attenuation (fc =100 kHz) 25 dB

2.8 Temperature Stability over -20 to +80°C ±50 %

2.9 I/O Impedance 1.5 kΩ NS = Not Specified

3.0 Test Circuit

N° Characteristics

3.1 Measurement Condition:

The reference temperature shall be 25 ±2°C. The measurement shall be performed at the temperature range of 5 to 35°C unless otherwise the result is doubtful.

3.2 Test Circuit and Equipment:

Oscillating frequency shall be measured by the standard test circuit as shown below. Resonant impedance shall be measured by HP87510A Network Analyzer. 1 Operating beyond this limit may result in change or permanent damage to the device.

Ceramic Filter | FM broadcast receiver Part number: LTUPC455GB 2.832.217h | Revision: A1 | Date: 26 January 2023 Specifications are subject to change without notice Copyright © 2016 to 2023 Rakon Limited. All rights reserved Page 2 of 4 www.rakonxpress.com

4.0 Physical Characterstics

N° Characteristics Test conditions Requirements

4.1 Random Drop The Filter shall be measured after 3 times random drops from the

height of 0.3M on the concrete floor. No visible damage and the measured values shall meet Table 1.

4.2 Vibration The Filter shall be measured after being applied vibration of the

amplitude of 1.5mm with 10 to 55Hz bands of vibration frequency to each of 3 perpendicular directions for 2 hours. The measured values shall meet Table 1. 4.3 Resistance to Soldering Heat Lead terminals are immersed up to 1.5mm from the Filter’s body in a solder bath of 230 ±5°C for 3 ±0.5 seconds, and then the Filter shall be measured after being placed in natural condition for 1 hour. The measured values shall meet Table 1.

4.4 Solderability Lead terminals are immersed in resin for 5 seconds and then immersed

in soa ldering bath of 230 ±5°C for 2 ±0.5 seconds. 95% min. lead terminals shall be wet with solder.

4.5 Washability Ultrasonic wash not available

5.0 Environmental Characteristics

N° Characteristics Test conditions Requirements

5.1 High Temperature After being placed in a chamber with +80 ±2°C for 96 ±4 hours and

then being placed in natural condition for 1 hour. The Filter shall be measured. No visible damage and the measured values shall meet Table 1.

5.2 Low Temperature After being placed in a chamber with -20 ±2°C for 96 ±4 hours and then

being placed in natural condition for 1 hour. The Filter shall be measured. The measured values shall meet Table 1.

5.3 Humidity After being placed in a chamber with 90 to 95%

R.H. at +40 ±2°C for 96 ±4 hours and then beaced in natural condition for 1 hour. The Filter shall be measured. The measured values shall meet Table 1.

5.4 Heat Shock After being kept at room temperature, the Filter shall be placed at

temperature of –20°C for 30 minutes, then the Filter shall be immediately placed at temperature of 80°C, after 30 minutes at temperature of 80°C, the Filter shall be returned to –20°C again. After 5 times above cycles, the Filter shall be returned to room temperature, after 1 hour in natural condition, the Filter shall be measured. The measured values shall meet Table 1. 5.5 Temperature Characteristic From temperature range of -20 to +85°C FTC < 0.3%

6.0 Table 1

Table 1 – Measurement Requirements Measurements Requirements Center Frequency 455±2.0 kHz max Bandwidth 6 dB 40 dB ±3.5 kHz min ±11.0 max Insertion Loss 7.0 dB max Ripple (fc ±3.0kHz) 3.0 dB max

Ceramic Filter | FM broadcast receiver Part number: LTUPC455GB 2.832.217h | Revision: A1 | Date: 26 January 2023 Specifications are subject to change without notice Copyright © 2016 to 2023 Rakon Limited. All rights reserved Page 3 of 4 www.rakonxpress.com

7.0 Package, marking and pin connections

N° Characteristics Specifications Model outline drawing 9.1 Package type SMD, 7.5 x 7.0 x 5.0 mm

9.2 Marking Line 1: P55GB

Line 2: * (See DATE CODE below)

9.3 Pin connections Pin 1:

Pin 2: Pin 3: Input GND Output

8.0 Packaging

N° Characteristics

8.1 TAPE DETAILS:

NOTE:

  • Unit: mm
  • Tolerence: ±0.3 mm
  • Leads are soldered on electrode and body is molded by resin * DATE CODE:

Ceramic Filter | FM broadcast receiver Part number: LTUPC455GB 2.832.217h | Revision: A1 | Date: 26 January 2023 Specifications are subject to change without notice Copyright © 2016 to 2023 Rakon Limited. All rights reserved Page 4 of 4 www.rakonxpress.com

8.2 REEL DETAILS:

9.0 Disclaimer

When something gets doubtful with this specification, we shall jointly work to get an agreement.

10.0 Specification History

Revision Change notes Date A0 Preliminary Datasheet creation Dec, 2nd 2016 A1 Re-branding Rakon to RakonXpress Jan, 26th 2023