LSM-2.5/10-D12EB

LSM-EB MURATA | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

Ḥ Features Designed to ease the evaluation of today's subminiature surface-mount technol- ogy (SMT) 10 Amp single output DC/DC power converters, DATEL's LSM-EB series includes twenty four models for all popular logic family output voltages and common input power voltages. Each LSM-EB model consists of a 4.31-inch square circuit board including a DATEL LSM-series surface mounted DC/DC converter, input/output banana jacks, trim circuits and various passive components. Rather than hand wiring to small mounting pads, the user can more accurately test real world electrical and thermal performance on a mounting board with a full ground plane and input Pi filter. The circuit board is mounted on four removable one-inch standoffs threaded for 4-40 screw attachment. The heart of the LSM-EB evaluation board is DATEL's advanced single output non-isolated LSM series DC/DC converter. Running from either 3.3 Volt, 5 Volt or

12 Volt DC input power, the LSM series provides high quality point-of-load (POL)

output power for CPU's, memory systems, microcontrollers and large array logic. See DATEL's LSM Series data sheet for full information. N Rapid evaluation of DATEL LSM series

10 Amp DC/DC converters

N Twenty-four models ranging from 0.8V to 5V single outputs at 10 Amps max. Ideal for mixed logic families. N For CPU, logic array and custom controller applications N Avoids initial user development of SMT mounting systems while offering realistic evaluation of a surface-mounted converter N Rugged banana jack I/O connections plus input Pi L-C filter N Provision for external shut-down control inputs and trim circuit evaluation N Includes test points for oscilloscope evaluation of performance ON/OFF CONTROL TRIM GND ON/OFF CONTROLJ1 THRU J4 ARE BANANA JACKS DIP SWITCH, SW1 OPEN CLOSED TRIM DOWN TRIM UP PIN 2 PIN 3 33μF 1μH 33μF ++ + + 22μF 22μF +VOUT+VOUT –VOUT +VIN +VIN –VIN +SENSE LSM-EB Series

10 Amp DC/DC Power Converter Evaluation Boards

www.murata-ps.com/rohs www.murata-ps.com Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000 MDC_LSM_EB.B01 Page 1 of 5

The board is laid out with filter capacitors and the inductor on the input and a filter capacitor on the output. These represent typical values that you would normally use in your application therefore, performance should be similar. Also, the values comply with those recommended in the LSM data sheet. The two trim resistor locations (R3 and R4) are left open for the user to install suitable trim resistors, either as axial lead resistors or "0805" surface mount resistors. White silkscreening on the board identifies all components. Usage Guidelines Refer to the LSM series data sheet for full details on the following topics. Input/Output Connections Holding the module upright, input power is applied to the left set of banana jacks. Output power is extracted from the right banana jacks. Please note that both ground terminals on the bottom are connected together internally. To retain high system performance, be sure to use the proper gauge wiring (12 gauge or larger is recommended). The hex standoffs are not connected to the ground plane. Use as short wiring as possible. For longer power wiring, to prevent noise radiation, consider either twisting the leads and/or enclosing the leads in a grounded copper shield. Input Pi Filter A classic Pi filter is provided on the converter's input. While this filter is not required if you can assure that the input voltage at the DC/DC terminals remains within the input voltage range at all times and is reason- ably low noise, many applications will see improved performance if the filter is employed. The filter is also useful for switching output loads and for evaluation of input ripple current. The inductor and associated capacitors are selected to prevent saturation and excessive power dissipation at the full 10 Amp output current while avoiding inductive spike damage to the DC/DC. The capacitors are chosen for low ESR. Specification Summary ~ DC/DC Converter type DATEL LSM series ~ Input Voltage 3.3, 5 or 12 Volts (see Ordering Guide) Output Voltage 0.8 to 5 Volts, (see Ordering Guide) Output Current 10 Amps, max. Minimum load Zero (no minimum load) Input and Output Terminals banana jacks (4 locations) 0.166-inch (4.22mm) removable Outline Dimensions 4.31" x 4.31" x 1.5" max. (including standoffs) Height above board 0.41" Standoffs € Four removable, 1.0" length, 4-40 threaded Fabrication Multi-layer printed circuit board Operating Temp. Range (Ambient, natural convection) –40 to +65/+71°C  ~See DATEL's LSM series data sheet for full information on the DC/DC converter.  Maximum operating temperature ranges are dependent on model type. See the LSM series converter data sheet. Temperature range may be extended with forced cooling. € The standoffs are not connected to the board ground plane. Use a discrete connection if you wish to ground the standoffs. Diagnostic Test Points Four pins are provided for a combination of measurements. Pins 1 and 2 sense the voltage immediately at the DC/DC inputs. Pins 3 and 4 display the output voltage. Connect these pins either to an oscilloscope or voltmeter. If preferred, the input inductor may be bypassed by shorting J1 to Pin 1. Input Current Measurement A current sense resistor (not supplied) may be conveniently installed across the input inductor from J1 to Pin 1 after removing inductor L1 with a surface mount hot air desoldering tool. Suggested resistor values are 2 to 5 milliohms. These values will not degrade operation of the DC/DC converter yet will develop sufficient voltage at full power for measurement by a digital voltmeter or oscilloscope. Note that the 'scope must be connected in differential mode. If preferred, a sense resistor can also be installed in series with either ground jack without having to remove L1. A sense resistor of several milliohms may be conveniently fabricated with several inches of 12 or 14 gauge wire. Digital On/Off Control The top section (SW1-A) of the 3-pole DIP switch enables the power output of the converter. Y ou may either do this manually with the rocker switch or connect an external logic gate to the pole nearest the output terminals on the back side of the board. Such an external gate should be referenced to the converter's power ground and use 5V TTL/LS logic. A small reed relay or an open collector NPN transistor or FET may also be used to control the DC/DC with the collector tied to the same control terminal pole on the DIP switch. The converter's on/off control includes an internal pullup resistor to +5V. The pullup is 5 to 14 kilohms, depending on model. Leave the on-board DIP switch open if you use any of these external controls. Use short leads if you install an external control. If the on/off control is left open, the converter will operate normally. Always make sure the DC/DC is powered up before activating the on/off control. Trim Circuits The bottom two sections of the 3-pole DIP switch connects the converter's single trim input to two external resistor positions immediately to the right of the switch body. See the schematic diagram. The upper resistor corresponds to the leg connecting to the +V OUT terminal and the bottom resistor connects to –VOUT. The switches allow you to temporarily disconnect the trim resistors to evaluate their effects. Y ou may either install discrete resistors in these two through-hole or surface mount locations or you may wire a closely-mounted 20 kilohm potentiometer between the board pads. Use short leads to prevent noise pickup and instability. Study the LSM data sheet for the required resistor values. Thermal Considerations The DC/DC converter, when mounted on the evaluation board, is rated up to approximately +65 degrees Centrigrade operation (depending on model) using natural convection at low or moderate altitude. The converter is pro- tected by thermal shutdown if overcurrent, higher altitude and/or overtemper- ature operation is attempted. Some heat is extracted through the mounting pads. Higher temperature operation is available with forced cooling. Carefully study the derating curves on the LSM data sheet. LSM-EB Series Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000www.murata-ps.com MDC_LSM_EB.B01 Page 2 of 5

A4.31 (109.47) 1.0 (25.4) 1.5 MAX. (38.1) 3.94 (100.08) A 3.94 (100.08) 4.31 (109.47) (4) HEX STANDOFFS 4-40 THREAD TOP VIEW DIMENSIONS ARE IN INCHES (MM) B B I/O Connections Terminal Function J1 +V IN external J2 –V IN external J3 +V OUT external J4 –V OUT external Pin 1 DC/DC +V IN Pin 2 DC/DC –V IN Pin 3 DC/DC –V OUT Pin 4 DC/DC +V OUT LSM-EB Series Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000www.murata-ps.com MDC_LSM_EB.B01 Page 3 of 5

them ideal for tape and reel automated surface mounting. important for battery operated and standby applications. converter from system 48 Volts to 12 Volts distributed to each POL converter. converter runs the CPU. A third 5V POL converter powers legacy I/O ports. lower cost non-isolated versions. system grounds and is not restricted by a noisy system "mecca" ground. Figure 2. Distributed Bus Architecture

All Evaluation Board models have 10 Amp maximum output current and use identical mounting and pad numbering. Three input voltages (3.3V, 5V and 12V) are offered. DATEL will review special or custom versions of other voltages for scheduled quantity applications. Model Number DC Output Voltage DC Input Range LSM-0.8/10-D3EB 0.8 Volts 3 to 3.6 Volts LSM-0.8/10-D5EB 0.8 Volts 4.5 to 5.5 Volts LSM-0.8/10-D12EB 0.8 Volts 10 to 14 Volts LSM-1/10-D3EB 1.0 Volts 3 to 3.6 Volts LSM-1/10-D5EB 1.0 Volts 4.5 to 5.5 Volts LSM-1/10-D12EB 1.0 Volts 10 to 14 Volts LSM-1.2/10-D3EB 1.2 Volts 3 to 3.6 Volts LSM-1.2/10-D5EB 1.2 Volts 4.5 to 5.5 Volts LSM-1.2/10-D12EB 1.2 Volts 10 to 14 Volts LSM-1.5/10-D3EB 1.5 Volts 3 to 3.6 Volts LSM-1.5/10-D5EB 1.5 Volts 4.5 to 5.5 Volts LSM-1.5/10-D12EB 1.5 Volts 10 to 14 Volts Model Number DC Output Voltage DC Input Range LSM-1.8/10-D3EB 1.8 Volts 3 to 3.6 Volts LSM-1.8/10-D5EB 1.8 Volts 4.5 to 5.5 Volts LSM-1.8/10-D12EB 1.8 Volts 10 to 14 Volts LSM-2/10-D3EB 2.0 Volts 3 to 3.6 Volts LSM-2/10-D5EB 2.0 Volts 4.5 to 5.5 Volts LSM-2/10-D12EB 2.0 Volts 10 to 14 Volts LSM-2.5/10-D3EB 2.5 Volts 3 to 3.6 Volts LSM-2.5/10-D5EB 2.5 Volts 4.5 to 5.5 Volts LSM-2.5/10-D12EB 2.5 Volts 10 to 14 Volts LSM-3.3/10-D5EB 3.3 Volts 4.5 to 5.5 Volts LSM-3.3/10-D12EB 3.3 Volts 10 to 14 Volts LSM-5/10-D12EB 5.0 Volts 10 to 14 Volts DATEL makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. The DATEL logo is a registered DATEL, Inc. trademark. 04/24/08 LSM-EB Series Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2008 Murata Power Solutions, Inc. USA: Mansfield (MA), Tel: (508) 339-3000, email: sales@murata-ps.com Canada: Toronto, Tel: (866) 740-1232, email: toronto@murata-ps.com UK: Milton Keynes, Tel: +44 (0)1908 615232, email: mk@murata-ps.com France: Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: france@murata-ps.com Germany: München, Tel: +49 (0)89-544334-0, email: munich@murata-ps.com Japan: Tokyo, Tel: 3-3779-1031, email: sales_tokyo@murata-ps.com Osaka, Tel: 6-6354-2025, email: sales_osaka@murata-ps.com Website: www.murata-ps.jp China: Shanghai, Tel: +86 215 027 3678, email: shanghai@murata-ps.com Guangzhou, Tel: +86 208 221 8066, email: guangzhou@murata-ps.com Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356 www.murata-ps.com email: sales@murata-ps.com ISO 9001 REGISTERED Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000www.murata-ps.com MDC_LSM_EB.B01 Page 5 of 5