LP8340 TI1 | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 18
Technical content
1.0µF Ceramic VOUT 1.0µF Ceramic VOUT GND VOUT Sense (LLP only) VIN LP8340 www.ti.com SNVS221D –FEBRUARY 2003–REVISED APRIL 2013 LP8340LowDropout,LowIQ,1.0ACMOS LinearRegulator Check forSamples: LP8340 1FEATURES DESCRIPTION The LP8340 low-dropoutCMOS linearregulatoris 2• ±1.5% TypicalVOUT Tolerance
- Wide OperatingRange 2.7Vto10V and 3ld PFM. The LP8340 can deliverup to 1.0A outputcurrent.• Internal1.0A PMOS Output Transistor
- 19µA TypicalQuiescentCurrent Typicaldropoutvoltageis420mV at1.0A forthe5.0V version,540mV at1.0A forthe3.3V version,670mV• Thermal Overload Limiting at1.0A forthe2.5V versionand 680mV at800mA for• Foldback CurrentLimiting the1.8Vversion.
- Zener Trimmed Bandgap Reference The LP8340 includesa zener trimmed bandgap• Space Saving WSON package voltage reference,foldback current limitingand
- Temperature Range thermaloverloadlimiting. – LP8340C 0°C to125°C The LP8340 featuresa PMOS outputtransistorwhich unlikePNP type low dropoutregulatorsrequiresno– LP8340I −40°C to125°C base drivecurrent.This allowsthe device ground currentto remain less than 50µA over operatingAPPLICATIONS temperature,supplyvoltageand irrespectiveof the• Hard Disk Drives loadcurrent.
- Notebook Computers
- BatteryPowered Electronics
- PortableInstrumentation TypicalApplications Figure1. FixedVOUT Pleasebe aware thatan importantnoticeconcerningavailability,standardwarranty,and use incriticalapplicationsof Texas Instrumentssemiconductorproductsand disclaimerstheretoappearsattheend ofthisdatasheet. 2Alltrademarksarethepropertyoftheirrespectiveowners. PRODUCTION DATA informationiscurrentas ofpublicationdate. Copyright© 2003–2013,Texas InstrumentsIncorporatedProductsconform to specificationsper the terms of the Texas Instrumentsstandardwarranty.Productionprocessingdoes not necessarilyincludetestingofallparameters.
3.3V 1.0µF Ceramic 1.5V 1.0µF Ceramic VOUT GND VIN ADJ 25k 125k LP8340 SNVS221D –FEBRUARY 2003–REVISED APRIL 2013 www.ti.com Figure2. AdjustableVOUT Connection Diagrams Bottom View Bottom View Figure3.6-PinWSON Package Figure4.6-PinWSON Package FixedOutput Voltage AdjustableOutput Voltage See Package Number NGD0006A See Package Number NGD0006A NOTE VIN Pins (Pin1 & 6) must be connected togetherexternallyforfull1 amp operation (500mA max perpin). VOUT Sense (Pin5)must be connectedtoVOUT (Pin4). Top View Figure5. PFM Package See Package Number NDP0003B These deviceshave limitedbuilt-inESD protection.The leadsshouldbe shortedtogetherorthedeviceplacedinconductivefoam duringstorageorhandlingtopreventelectrostaticdamage totheMOS gates.
2 SubmitDocumentationFeedback Copyright© 2003–2013,Texas InstrumentsIncorporated
ProductFolderLinks:LP8340
PD = TJ(MAX) - TA TJA (4) Maximum Power dissipationforthedeviceiscalculatedusingthefollowingequations: where TJ(MAX) isthemaximum LP8340 www.ti.com SNVS221D –FEBRUARY 2003–REVISED APRIL 2013 AbsoluteMaximum Ratings(1)(2)(3) VIN,VOUT ,VOUT Sense,ADJ −0.3Vto12V StorageTemperatureRange −65°C to160°C JunctionTemperature(TJ) 150°C Power Dissipation See (4) ESD Rating Human Body Model(5) 2kV Machine Model 200V (1) AbsoluteMaximum ratingsindicatelimitsbeyond whichdamage may occur.Electricalspecificationsdo notapplywhen operatingthe deviceoutsideofitsratedoperatingconditions. (2) Allvoltagesarewithrespecttothepotentialatthegroundpin. (3) IfMilitary/Aerospacespecifieddevicesarerequired,pleasecontacttheTexas InstrumentsSalesOffice/Distributorsforavailabilityand specifications. junctiontemperature,TA istheambienttemperature,and θJA isthejunction-to-ambientthermalresistance.The valueoftheθJA forthe WSON package isspecificallydependanton thePCB tracearea,tracematerial,and thenumber oflayersand thermalvias.For improvedthermalresistanceand power dissipationfortheWSON package,refertoApplicationNote AN-1187 (SNOA401 ). (5) Human body model 1.5kΩ inserieswith100pF. OperatingRatings(1)(2) SupplyVoltage 2.7to10V TemperatureRange LP8340C 0°C to125°C LP8340I −40°C to125°C (1) AbsoluteMaximum ratingsindicatelimitsbeyond whichdamage may occur.Electricalspecificationsdo notapplywhen operatingthe deviceoutsideofitsratedoperatingconditions. (2) Allvoltagesarewithrespecttothepotentialatthegroundpin. LP8340C ElectricalCharacteristics UnlessotherwisespecifiedalllimitsensuredforVIN = VO + 1V,C IN = C OUT = 10μF,TJ = 25°C. Boldfacelimitsapplyoverthe fulloperatingtemperaturerangeofTJ = 0°C to125°C Symbol Parameter Conditions Min (1) Typ (2) Max (1) Units VOUT OutputVoltage LP8340-ADJ,ADJ = OUT 800mA <IOUT ≤1.0A,3.2V≤VIN ≤VOUT +4V 1.213 1.288 LP8340-1.8 800mA <IOUT ≤1.0A,3.4V≤VIN ≤6V 1.746 1.854 LP8340-2.5 IOUT = 10mA, VIN = 3.8V,TJ = 25°C 2.463 2.500 2.538 V LP8340-3.3 IOUT = 10mA, VIN = 4.3VTJ = 25°C 3.250 3.300 3.350 V LP8340-5.0 IOUT = 10mA, VIN = 6V,TJ = 25°C 4.925 5.000 5.075 V 100μA ≤IOUT ≤1.0A,6V ≤VIN ≤9V 4.850 5.150 (1) Alllimitsarespecifiedby testingorstatisticalanalysis. (2) TypicalValuesrepresentthemost likelyparametricnorm. Copyright© 2003–2013,Texas InstrumentsIncorporated SubmitDocumentationFeedback 3 ProductFolderLinks:LP8340
SNVS221D –FEBRUARY 2003–REVISED APRIL 2013 www.ti.com LP8340C ElectricalCharacteristics(continued) UnlessotherwisespecifiedalllimitsensuredforVIN = VO + 1V,C IN = C OUT = 10μF,TJ = 25°C. Boldfacelimitsapplyoverthe fulloperatingtemperaturerangeofTJ = 0°C to125°C Symbol Parameter Conditions Min (1) Typ (2) Max (1) Units ΔVO Load Regulation LP8340-ADJ,ADJ=OUT IOUT = 1mA to1.0A,VIN = 3.2V 6 25 LP8340-1.8 IOUT = 1mA to1.0A,VIN = 3.4V 8 30 LP8340-2.5 mVIOUT = 1mA to1.0A,VIN = 3.5V 15 50 LP8340-3.3 IOUT = 1mA to1.0A,VIN = 4.3V 20 75 LP8340-5.0 IOUT = 1mA to1.0A,VIN = 6V 25 100 ΔVO LineRegulation VOUT + 0.5V≤VIN ≤10V,IOUT = 25mA (3) 4 15 mV VIN − VO DropoutVoltage(3)(4) LP8340-1.8 IOUT = 800mA 680 1400 LP8340-2.5 IOUT = 800mA 550 1000 LP8340-2.5 IOUT = 1.0A 670 1300 LP8340-3.3 mVLP8340-ADJ,VOUT = 3.3V,IOUT = 800mA 420 800 LP8340-3.3 LP8340-ADJ,IOUT = 1.0A 540 1000 LP8340-5.0 IOUT = 800mA 330 650 LP8340-5.0 IOUT = 1.0A 420 800 IQ QuiescentCurrent VIN ≤10V 19 50 μA Minimum Load Current VIN − VOUT ≤4V 100 μA ILIMIT FoldbackCurrentLimit VIN − VOUT >5V 450 mA VIN − VOUT <4V 1600 RippleRejectionRatio VIN (dc)= VOUT + 2V 48 55 dB VIN (ac)= 1 VP-P @ 120Hz TSD ThermalShutdown Temp. 160 °CThermalShutdown Hyst. 10 ADJ InputLeakage Current VADJ = 1.5Vor0V ±0.01 ±100 nA VOUT Leakage Current LP8340-ADJ ADJ = OUT, VOUT = 2V,VIN = 10V 10 LP8340-1.8,VOUT = 2.5V,VIN = 10V 10 μALP8340-2.5,VOUT = 3.5V,VIN = 10V 10 LP8340-3.3,VOUT = 4V,VIN = 10V 10 LP8340-5.0,VOUT = 6V,VIN = 10V 10 en OutputNoise 10Hz to10kHz,R L = 1kΩ,C OUT = 10μF 250 μVrms (3) Conditiondoes notapplytoinputvoltagesbelow2.7Vsincethisistheminimum inputoperatingvoltage. (4) Dropoutvoltageismeasured by reducingVIN untilVO drops100mV fromitsnormalvalue.
4 SubmitDocumentationFeedback Copyright© 2003–2013,Texas InstrumentsIncorporated
ProductFolderLinks:LP8340
www.ti.com SNVS221D –FEBRUARY 2003–REVISED APRIL 2013 LP8340I ElectricalCharacteristics UnlessotherwisespecifiedalllimitsensuredforVIN = VO + 1V,C IN = C OUT = 10μF,TJ = 25°C. Boldfacelimitsapplyoverthe fulloperatingtemperaturerangeofTJ = −40°C to125°C Symbol Parameter Conditions Min (1) Typ (2) Max (1) Units VOUT OutputVoltage LP8340-ADJ,ADJ = OUT 800mA <IOUT ≤1.0A,3.2V≤VIN ≤VOUT +4V 1.213 1.288 LP8340-1.8 800mA <IOUT ≤1.0A,3.4V≤VIN ≤6V 1.746 1.854 LP8340-2.5 IOUT = 10mA, VIN = 3.8V,TJ = 25°C 2.463 2.500 2.538 V LP8340-3.3 IOUT = 10mA, VIN = 4.3VTJ = 25°C 3.250 3.300 3.350 V LP8340-5.0 IOUT = 10mA, VIN = 6V,TJ = 25°C 4.925 5.000 5.075 V 100μA ≤IOUT ≤1.0A,6V ≤VIN ≤9V 4.850 5.150 ΔVO Load Regulation LP8340-ADJ,ADJ=OUT IOUT = 1mA to1.0A,VIN = 3.2V 6 25 LP8340-1.8 IOUT = 1mA to1.0A,VIN = 3.4V 8 30 LP8340-2.5 mVIOUT = 1mA to1.0A,VIN = 3.5V 15 50 LP8340-3.3 IOUT = 1mA to1.0A,VIN = 4.3V 20 75 LP8340-5.0 IOUT = 1mA to1.0A,VIN = 6V 25 100 ΔVO LineRegulation VOUT + 0.5V≤VIN ≤10V,IOUT = 25mA (3) 4 15 mV VIN − VO DropoutVoltage(3)(4) LP8340-1.8 IOUT = 800mA 680 1400 LP8340-2.5 IOUT = 800mA 550 1000 LP8340-2.5 IOUT = 1.0A 670 1300 LP8340-3.3 mVLP8340-ADJ,VOUT = 3.3V,IOUT = 800mA 420 800 LP8340-3.3 LP8340-ADJ,IOUT = 1.0A 540 1000 LP8340-5.0 IOUT = 800mA 330 650 LP8340-5.0 IOUT = 1.0A 420 800 IQ QuiescentCurrent VIN ≤10V 19 50 μA Minimum Load Current VIN − VOUT ≤4V 100 μA ILIMIT FoldbackCurrentLimit VIN − VOUT >5V 450 mA VIN − VOUT <4V 1600 RippleRejectionRatio VIN (dc)= VOUT + 2V 48 55 dB VIN (ac)= 1 VP-P @ 120Hz (1) Alllimitsarespecifiedby testingorstatisticalanalysis. (2) TypicalValuesrepresentthemost likelyparametricnorm. (3) Conditiondoes notapplytoinputvoltagesbelow2.7Vsincethisistheminimum inputoperatingvoltage. (4) Dropoutvoltageismeasured by reducingVIN untilVO drops100mV fromitsnormalvalue. Copyright© 2003–2013,Texas InstrumentsIncorporated SubmitDocumentationFeedback 5 ProductFolderLinks:LP8340
SNVS221D –FEBRUARY 2003–REVISED APRIL 2013 www.ti.com LP8340I ElectricalCharacteristics(continued) UnlessotherwisespecifiedalllimitsensuredforVIN = VO + 1V,C IN = C OUT = 10μF,TJ = 25°C. Boldfacelimitsapplyoverthe fulloperatingtemperaturerangeofTJ = −40°C to125°C Symbol Parameter Conditions Min (1) Typ (2) Max (1) Units TSD ThermalShutdown Temp. 160 °CThermalShutdown Hyst. 10 ADJ InputLeakage Current VADJ = 1.5Vor0V ±0.01 ±100 nA VOUT Leakage Current LP8340-ADJ ADJ = OUT, VOUT = 2V,VIN = 10V 10 LP8340-1.8,VOUT = 2.5V,VIN = 10V 10 μALP8340-2.5,VOUT = 3.5V,VIN = 10V 10 LP8340-3.3,VOUT = 4V,VIN = 10V 10 LP8340-5.0,VOUT = 6V,VIN = 10V 10 en OutputNoise 10Hz to10kHz,R L = 1kΩ,C OUT = 10μF 250 μVrms
6 SubmitDocumentationFeedback Copyright© 2003–2013,Texas InstrumentsIncorporated
ProductFolderLinks:LP8340
RIPPLE REJECTION (dB) FREQUENCY (Hz) 2.5 5 7.5 10 12.5 GROUND CURRENT (µA) INPUT VOLTAGE (V) 0 25 50 75 100 125 17.5 18.5 GROUND CURRENT (µA) TEMPERATURE (° C) 0 200 400 600 800 1000 GROUND CURRENT (µA) LOAD CURRENT (mA) 0° C 25° C 125° C 0 25 50 75 100 125 -1.50 -1.00 -0.50 0.00 0.50 1.00 1.50 VOUT CHANGE (%) TEMPERATURE (° C) 0 200 400 600 800 1000 100 200 300 400 500 600 700 800 DROPOUT VOLTAGE (mV) LOAD CURRENT (mA) 3.3V 2.5V 5.0V LP8340 www.ti.com SNVS221D –FEBRUARY 2003–REVISED APRIL 2013 TypicalPerformance Characteristics Unlessotherwisespecified,VIN = VO + 1.5V,C IN = C OUT = 10μF X7R ceramic,TJ = 25°C Output VoltageChange vs.Temperature Dropout Voltagevs.Load Current Figure6. Figure7. Ground Currentvs.Temperature (ILOAD = 1A) Ground Currentvs.Load Current Figure8. Figure9. Ground Currentvs.InputVoltage RippleRejectionRatiovs.Frequency Figure10. Figure11. Copyright© 2003–2013,Texas InstrumentsIncorporated SubmitDocumentationFeedback 7 ProductFolderLinks:LP8340
RISE TIME (mS) 0.1 100 ILOAD (mA) 0.01 0.1 1 10 VIN = 10V VOUT = 1.25V C IN = 1µF OVERSHOOT < 5% C OUT = 1µF C OUT = 10µF C OUT = 4.3µF 50µs/DIV VOUT (2V/DIV) VIN (0 to 5.0V) 200µs/DIV VOUT (100mV/DIV) IOUT (10mA to 1.0A) 200µs/DIV VOUT (100mV/DIV) VIN (4.0V to 5.0V) 500 600 700 800 900 1000 MIN V IN (V) ILOAD (mA) 125° C 3.3 3.2 3.1 3.0 2.9 2.8 2.7 2.6 2.5 2.4 2.3 0° C 25° C 600 700 800 900 1000 2.4 2.6 2.8 3.0 3.2 3.4 3.6 MIN V IN (V) ILOAD (mA) 25° C 125° C 0° C 500 LP8340 SNVS221D –FEBRUARY 2003–REVISED APRIL 2013 www.ti.com TypicalPerformance Characteristics(continued) Unlessotherwisespecified,VIN = VO + 1.5V,C IN = C OUT = 10μF X7R ceramic,TJ = 25°C LP8340-1.8VMin VIN LP8340-ADJ Min VIN Figure12. Figure13. Load TransientResponse LineTransientResponse (ILOAD = 10mA) Figure14. Figure15. Start-upResponse Minimum InputVoltageRise Time Figure16. Figure17.
8 SubmitDocumentationFeedback Copyright© 2003–2013,Texas InstrumentsIncorporated
ProductFolderLinks:LP8340
RISE TIME (mS) 0.1 100 ILOAD (mA) 0.01 0.1 1 10 VIN = 10V VOUT = 5V C IN = 1µF OVERSHOOT < 5% C OUT = 1µF C OUT = 10µF C OUT = 4.3µF RISE TIME (mS) 0.1 100 ILOAD (mA) 0.01 0.1 1 10 VIN = 10V VOUT = 3.3V C IN = 1µF OVERSHOOT < 5%C OUT = 1µF C OUT = 10µF C OUT = 4.3µF RISE TIME (mS) 0.1 100 ILOAD (mA) 0.01 0.1 1 10 VIN = 10V VOUT = 1.8V C IN = 1µF OVERSHOOT < 5% C OUT = 1µF C OUT = 10µF C OUT = 4.3µF RISE TIME (mS) 0.1 100 ILOAD (mA) 0.01 0.1 1 10 VIN = 10V VOUT = 2.5V C IN = 1µF OVERSHOOT < 5% C OUT = 1µF C OUT = 10µF C OUT = 4.3µF LP8340 www.ti.com SNVS221D –FEBRUARY 2003–REVISED APRIL 2013 TypicalPerformance Characteristics(continued) Unlessotherwisespecified,VIN = VO + 1.5V,C IN = C OUT = 10μF X7R ceramic,TJ = 25°C Minimum InputVoltageRise Time Minimum InputVoltageRise Time Figure18. Figure19. Minimum InputVoltageRise Time Minimum InputVoltageRise Time Figure20. Figure21. Copyright© 2003–2013,Texas InstrumentsIncorporated SubmitDocumentationFeedback 9 ProductFolderLinks:LP8340
THERMAL SHUTDOWN 1.25V REFERENCE GND MOSFET DRIVER FOLDBACK CURRENT LIMIT VIN P VOUT Fixed VOUT R 1 R 2 ADJ P Adjustable Version DPAK Only VOUT SENSE ERROR AMP LP8340 SNVS221D –FEBRUARY 2003–REVISED APRIL 2013 www.ti.com APPLICATIONS SECTION GENERAL INFORMATION The LP8340 isa low-dropout,low quiescentcurrentlinearregulator.As shown inFigure22 itconsistsofa 1.25V reference,erroramplifier,MOSFET driver,PMOS pass transistorand forthefixedoutputversions,an internal feedbacknetwork(R1/R2).Inaddition,thedeviceisprotectedfromoverloadby a thermalshutdown circuitand a foldbackcurrentlimitcircuit The 1.25V referenceisconnectedtotheinvertinginputoftheerroramplifier.Regulationoftheoutputvoltageis achievedby means ofnegativefeedbacktothenon-invertinginputoftheerroramplifier.Feedback resistorsR 1 and R 2 are eitherinternalor externalto the device,dependingon whetheritisa fixedvoltageversionor the adjustableversion.The negativefeedbackand highopen loopgainoftheerroramplifiercause thetwo inputsof the erroramp to be virtuallyequal in voltage.Ifthe outputvoltagechanges due to load changes,the error amplifierand MOSFET driverprovidetheappropriatedrivetothepass transistortomaintaintheerroramplifier’s inputsas virtuallyequal. Figure22. LP8340 FunctionalBlock Diagram EXTERNAL CAPACITOR An Inputcapacitorof1μF orgreaterisrequiredbetween theLP8340 VIN pinand ground.While1μF willprovide adequatebypassingoftheVIN supplylargervaluesofinputcapacitor(i.e.10μF)can provideimprovedbypassing ofpower supplynoise. Stableoperationcan be achievedwithan outputcapacitorof 1μF or greater,eitherceramicX7R dielectricor aluminum/tantalumelectrolytic.While the minimum capacitorvalueis1μF, the typicaloutputcapacitorvalues selectedrange from 1μF to 10μF. The largervaluesprovideimprovedload-transientresponse,power supply rejectionand stability.
10 SubmitDocumentationFeedback Copyright© 2003–2013,Texas InstrumentsIncorporated
ProductFolderLinks:LP8340
R 1 = R 2 VO 1.25V - 1 VO = VREF R 1 R 2 + 1 LP8340 www.ti.com SNVS221D –FEBRUARY 2003–REVISED APRIL 2013 OUTPUT VOLTAGE SETTING (ADJ VERSION ONLY) The outputvoltageissetaccordingtotheamount ofnegativefeedback(Notethatthepass transistorinvertsthe feedbacksignal).Thisfeedbackisdeterminedby R 1 and R 2 withtheresultingoutputvoltagerepresentedby the followingequation: (1) Use the followingequationto determinethe values of R 1 and R 2 for a desiredVOUT (R2 = 100kΩ is recommended). (2) MINIMUM LOAD CURRENT A minimum loadof100μA isrequiredforregulationand stabilityovertheentireoperatingtemperaturerange.If actualload currentfallbelow 100μA itisrecommended thata resistorof valueR L = VO /100μA be placed between VO and ground. START UP CONSIDERATIONS Under certainoperatingconditions,overshootof VOUT at start-upcan occur.The observed overshootis a functionof risetimeof VIN waveform,C OUT , start-uploadcurrent,and VIN−VOUT differential.The relationship between theseconditionsisshown intheTypicalPerformanceCharacteristicscurves(Minimum InputVoltage RiseTime).VIN risetimesabove thecurveresultin<5% overshoot. CustomersareencouragedtocheckthesuitabilityofLP8340 intheirspecificapplication. Copyright© 2003–2013,Texas InstrumentsIncorporated SubmitDocumentationFeedback 11 ProductFolderLinks:LP8340
SNVS221D –FEBRUARY 2003–REVISED APRIL 2013 www.ti.com
REVISION HISTORY
Changes from RevisionC (April2013)toRevisionD Page
12 SubmitDocumentationFeedback Copyright© 2003–2013,Texas InstrumentsIncorporated
ProductFolderLinks:LP8340
www.ti.com 9-Aug-2016 Addendum-Page 1 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/Ball Finish (6) MSL Peak Temp (3) Op Temp (°C) Device Marking (4/5) Samples LP8340ILDX-ADJ NRND WSON NGD 6 TBD Call TI Call TI 0 to 125 L078B LP8340ILDX-ADJ/NOPB ACTIVE WSON NGD 6 4500 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR 0 to 125 L078B (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
www.ti.com 9-Aug-2016 Addendum-Page 2 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
*All dimensions are nominal Device Package Type Package Drawing Pins SPQ Reel Diameter (mm) Reel Width W1 (mm) (mm) (mm) (mm) (mm) W (mm) Pin1 Quadrant PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2016 Pack Materials-Page 1
*All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP8340ILDX-ADJ/NOPB WSON NGD 6 4500 367.0 367.0 35.0 PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2016 Pack Materials-Page 2
www.ti.com
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic”are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2016, Texas Instruments Incorporated