DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

Series LP01 Short Body Pushbuttons www.nkk.comD66 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons DIlluminated PBSlides Programmable RockersTouch Tilt Toggles General Specifications Electrical Capacity (Resistive Load) Power Level (silver): 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC Other Ratings Contact Resistance: 50 milliohms maximum Insulation Resistance: 200 megohms minimum @ 500V DC Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum 1,500V AC minimum between contacts and case for 1 minute minimum Mechanical Life: 500,000 operations minimum Electrical Life: 50,000 operations minimum for 3A @ 125V/250V AC & 3A @ 30V DC 100,000 operations minimum for 1A @ 125V/250V AC & 1A @ 30V DC Nominal Operating Force: 1.5N for Single Pole; 3.0N for Double Pole Contact Timing: Nonshorting (break-before-make) Travel: Total Travel .118” (3.0mm) Materials & Finishes Actuator: Polycarbonate Housing: Bushing mount: Glass fiber reinforced polyamide (UL94V-0); Snap in mount: Polyphenylene ether (UL94V-0) Base: Diallyl phthalate (UL94V-0) Movable Contact: Phosphor bronze & silver with silver plating Stationary Contacts: Common terminal: Phosphor bronze with silver plating; Contact terminals: Phosphor bronze with tin & copper plating Lamp Terminals: Phospher bronze with tin and copper plating Environmental Data Operating Temperature Range: –10°C through +50°C (+14°F through +122°F) for Illuminated –25°C through +70°C (+13°F through +158°F) for Nonilluminated Humidity: 90 ~ 95% humidity for 240 hours @ 40°C (104°F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Mounting Torque: 0.8Nm (7.08 lb •in) Soldering Time & Temperature: Manual Soldering: See Profile A in Supplement section. Cleaning: Hand clean locally with alcohol based solution Standards & Certifications Flammability Standards: UL94V-0 housing & base UL: File No. E44145 All single & double pole models recognized at 3A @ 125V/250V AC or 3A @ 30V DC. Add “/U” to end of part number to order UL mark on switch. Add “/CUL” to end of part number to order cULus mark on switch.

Series LP01Short Body Pushbuttons www.nkk.com D67 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons D Illuminated PBSlides Programmable TogglesRockersTouch Tilt Distinctive Characteristics Environmentally friendly components and packaging materials meet RoHS Directive restricting use of hazardous materials. Suited for lead-free soldering because of heat resistant resin materials. Smooth, slightly concave surface of cap designed to fit fingertip. Unique design and construction of cap prevents its removal and limits tampering. Bright LED illumination in choice of red, green, or amber through translucent white cap. Short body of .551” (14.0mm) conserves behind-panel space. Combination solder lug and .110” quick connect terminals. Crisp actuation and clear circuit status provided by snap-action contact mechanism. Arc barrier between movable contacts protects against crossover. Actual Size

Series LP01 Short Body Pushbuttons www.nkk.comD68 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons DIlluminated PBSlides Programmable RockersTouch Tilt Toggles TYPICAL SWITCH ORDERING EXAMPLE LP01 White Cap SPDT ON-(ON) Circuit DESCRIPTION FOR TYPICAL ORDERING EXAMPLE LP0115CCKW015CB Red LED C B Black Housing Bushing Mount Silver Contacts Rated 3A @ 125/250V AC; Solder Lug/Quick Connect Terminals Cap Color B White K LEDs 5C Red 5D Amber 5F Green C51 Plunger Position ( ) = Momentary Connected Terminals Throw & Power/Lamp Schematics Pole Model Normal Down Normal Down Note: Terminal markings “COM, NO, NC, L, + and – ” are actually on the switch; terminal numbers are not on the switch. SP LP0115 ON (ON) 1-3 1-2 SPDT DP LP0125 ON (ON) 1-3 4-6 1-2 4-5 DPDT POLES & CIRCUIT (COM) 32 5 (COM) L (+) (-) L L (+) (-) L W01 Mounting Types C Bushing M Snap-in IMPORTANT: Switches are supplied without UL & cULus markings unless specified. Specific models & ratings noted on General Specifications page. Nonilluminated No Code Nonilluminated Nonilluminated Cap Colors A Black C Red F Green Poles

1 SPDT

2 DPDT

Contacts & Terminals W01 Silver Rated 3A @ 125V AC/250V AC Solder Lug/ Quick Connect Terminals* Circuit

5 ON (ON)

( ) = Momentary Housing K Black * Wire harness & cable assemblies offered only in Americas

Series LP01Short Body Pushbuttons www.nkk.com D69 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons D Illuminated PBSlides Programmable TogglesRockersTouch Tilt MOUNTING TYPES C MBushing .630” (16.0mm) Diameter This mounting option is supplied with a brass hexagon nut with nickel plating. Snap-in .669” (17.0mm) Diameter K HOUSING Black Housing available in black only. The one-piece body and bezel have a matte finish. Recommended Panel Thickness: .079” ~ .256” (2.0mm ~ 6.5mm) Recommended Panel Thickness: .039” ~ .126” (1.0mm ~ 3.2mm) Allow .984” (25.0mm) distance from center-to-center between switches when mounted side-by-side. Allow .827” (21.0mm) distance from center-to-center between switches when mounted side-by-side. W01 CONTACT MATERIALS, RATINGS, & TERMINALS Silver Power Level Solder Lug/ .110” (2.8mm) Quick Connect 3A @ 125V AC/250V AC; 3A @ 30V DC (7.3) .287 Epoxy Seal (2.8) .110 (1.2) .047 (2.0) .079 Thk = (0.5) .020 (0.6) R .024 (16.0) Dia .630 (1.7) .067 (7.5) .295 (25.0) Min .984 + 0.2 – 0.0 + 0.0 – 0.1 + 0.1 – 0.0 (1.1) R .043 (17.3) Dia .681 (18.1) .713 (21.0) Min .827 + 0.2 – 0.0 + 0.2 – 0.0 + 0.2 – 0.0 Note: If used at 1A @ 125V AC/250V AC or 1A @ 30V DC, electrical life will be 100,000 operations minimum. LED COLORS & SPECIFICATIONS The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires external power source. Polarity marks are on the switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. LEDs are an integral part of the switch and are not available separately. Colors Red Amber Green Forward Peak Current I FM 30mA 30mA 30mA Continuous Forward Current IF 20mA 20mA 20mA Forward Voltage VF 1.95V 2.0V 2.1V Reverse Peak Voltage VRM 5V 5V 5V Current Reduction Rate Above 25°C ∆IF 0.41mA/°C 0.29mA/°C 0.39mA/°C Ambient Temperature Range –10°C ~ +50°C 5D 5F5CSingle Color LED with 1 Element (+) (-) No Code No Lamp

Series LP01 Short Body Pushbuttons www.nkk.comD70 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons DIlluminated PBSlides Programmable RockersTouch Tilt Toggles TYPICAL SWITCH DIMENSIONS Bushing Mount • Single Pole Bushing Mount • Double Pole LP0115CCKW015CB LP0125CCKW015CB (13.6) Dia .535 (20.0) Dia .787 (2.5) .098 (7.3) .287 (21.3) .838 M16 P1 (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 (5.5) .217 (2.8) Typ .110 (9.7) .382 NC L NO NO COM (3.0) .118 (5.55) .219 (3.7) .146 (2.5) .098 (7.3) .287 (21.3) .838 M16 P1 (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 (5.5) .217 (2.8) Typ .110 (9.7) .382 NC L NO NO COM (6.0) .236 (11.1) .437 (3.7) .146 (13.6) Dia .535 (20.0) Dia .787 White B CAP COLORS The translucent cap is an integral part of the switch and is not available separately. Material: Polycarbonate Finish: Matte A C Cap Colors Available: Nonilluminated Caps Black Red Illuminated Cap F Green The cap is an integral part of the switch and is not available separately. Material: Polycarbonate Finish: Matte Cap Color Available:

Series LP01Short Body Pushbuttons www.nkk.com D71 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons D Illuminated PBSlides Programmable TogglesRockersTouch Tilt TYPICAL SWITCH DIMENSIONS LEGENDS Snap-in • Single Pole LP0125CMKW015DB LP0115CMKW015CB Snap-in • Double Pole (13.6) Dia .535 (20.0) Dia .787 (2.5) .098 (7.3) .287 (21.3) .838 (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 (5.5) .217 (2.8) Typ .110 NC NO NO COM (9.7) .382 (3.0) .118 (5.55) .219 (3.7) .146 L (13.6) Dia .535 (20.0) Dia .787 (2.5) .098 (7.3) .287 (21.3) .838 (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 (5.5) .217 (2.8) Typ .110 NC NO NO COM (6.0) .236 (11.1) .437 (3.7) .146 L (9.7) .382 Shaded area is printable area Recommended Methods: Pad Print or Laser Etch on cap. Epoxy based ink is recommended. Suggested Printable Area for LP01 Cap (12.07) Dia .475 (13.6) Dia .535 (0.76) Typ .030 PWR NKK Switches can provide custom legends for caps. Contact factory for more information.