LML6-C1-CW-SP DIALIGHT | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
pFully modular linear arrays of ultra high brightness LEDs pUtilizes the latest 100+ lumen LUXEON ® Rebel™ LEDs for cool white, 100+ lumen for neutral white & 50+ lumen for warm white pChoice of colour temperatures & optical patterns p>70% lumen maintenance @ 60,000 hours at max acceptable ambient temperature pETL recognized pLifesaver® thermal protection pPrimary heatsinking included pOperating ambient temperature -30ºC to +55ºC (@350mA) pRequires constant current driver pCompatible drivers include Dialight Lumidrives PWD60-35-70 Runs 3-8 modules @ 350mA, 2-4 modules @700mA pAdditional heatsinking required when driven @ 700mA APPLICATION pLinear lighting p Accent lighting p Flood lighting p Street & area lighting p General illumination MATERIALS / FINISH p Six premium flux LUXEON Rebel LEDs per module p Annodized cast aluminum heatsink p Polycarbonate cover p Dialight-Lumidrives optics (OPC 11 Series) p Modular quick connect cables p Module to module connector cable included
ORDERING INFORMATION
SP = 5 degree spot MD = 8 degree med. WD = 20 degree wide OV = 5X25 degree oval FR = 7 degree frosted spot Optic (BB) CW = 5000K - 6350K NW = 3800K - 4100K WW = 2850K - 3250K Typical Colour (AA) Temperature LML6-CON-CAB = Entry cable, driver to 1st module LML6-TER-CAB = End plug (required) * Cables use 0.5mm2 AWG12 wires Connectors (sold seperately) RECOGNIZED COMPONENT www.dialight.com
IES 32 files available, consult factory ASSEMBLY INFORMATION 1) Position ‘tab’ end of first powerwhite module by input wires/driver. (Do not connect power to entry cable before completing steps 2-6 ) 2) Remove cover from module ( Do not remove mask). Modules may be screwed down onto surface by inserting two M6 or 8/32 flathead screws through screw holes. 3) Insert 6 pin prong from LML6-CON-CAB entry cable into 6 prong receptacle near tab end of first module. 4) Insert 4 pin prong from connector cable into ‘notch’ end of module, insert 6 pin prong from connector cable into ‘tab’ end of next module (repeat for each additional module). 5) Connector cable wires can be routed through interior of modules by placing them into interior wire holders. 6) Insert LML6-TER-CAB 4-pin terminal prong into ‘notch’ end of last module in run (required). 7) Replace covers and connect power to LM60-CON-CAB INPUT WIRE CHART Colour wire on A50-LML6-CON-CAB entry cable To. or Connect to on PWD60-35-70 White 1 Thermistor Wire 5 White 2 Thermistor Wire 6 Red Driver + Wire 2 350mA Wires 1 & 2 700mA Black Driver - Wire 3 Green Ground Green / Yellow Stripe (297.18mm x 38.05mm x 14.86mm) Mounting hole spacing = 3.22” (81.8mm) Max screw size #8 Total length for “Z” units connected end to end = (Z x 11.7) - ((Z-1) x 0.25) (inches) Example: 2 units total length = 23.15” (588.01) Top View Side View MECHANICAL DIMENSIONS Dimensions in mm www.dialight.com Dialight reserves the right to make changes at any time in order to supply the best product possible. The most current version of this document will always be available at: www.dialight.com/Assets\\Brochures_And_Catalogs\\Illumination\\MDEXLUMPWM.pdf MDEXLUMPWM_B