LM211_05 ONSEMI | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 10
Technical content
Features
- Pb−Free Packages are Available
Figure 1. Typical Comparator Design Configurations GND pin is used as an output. GND pin is used as an output. dimensions section on page 2 of this data sheet.
ORDERING INFORMATION
http://onsemi.com PDIP−8 N SUFFIX CASE 626 SOIC−8 D SUFFIX CASE 7511 MARKING DIAGRAMS x = 2 or 3 A = Assembly Location WL, L = Wafer Lot YY, Y = Year WW, W = Work Week G = Pb−Free Package /C0071 = Pb−Free Package LM311AN AWL YYWWG LMx11 ALYW /C0071
LM211, LM311 http://onsemi.com Device Package Shipping† LM211D SOIC−8 98 Units / Rail LM211DG SOIC−8 (Pb−Free) 98 Units / Rail LM211DR2 SOIC−8 2500 Units / Tape & Reel LM211DR2G SOIC−8 (Pb−Free) 2500 Units / Tape & Reel LM311D SOIC−8 98 Units / Rail LM311DG SOIC−8 (Pb−Free)
98 Units / Rail
LM311DR2 SOIC−8 2500 Units / Tape & Reel LM311DR2G SOIC−8 (Pb−Free) 2500 Units / Tape & Reel LM311N PDIP−8 50 Units / Rail LM311NG PDIP−8 (Pb−Free) 50 Units / Rail †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. MAXIMUM RATINGS (TA = +25°C, unless otherwise noted.) Rating Symbol LM211 LM311 Unit Total Supply Voltage VCC +⎥VEE⎥ 36 36 Vdc Output to Negative Supply Voltage VO −VEE 50 40 Vdc Ground to Negative Supply Voltage VEE 30 30 Vdc Input Differential Voltage VID ±30 ±30 Vdc Input Voltage (Note 2) Vin ±15 ±15 Vdc Voltage at Strobe Pin − VCC to VCC−5 VCC to VCC−5 Vdc Power Dissipation and Thermal Characteristics Plastic DIP PD 625 mW Derate Above TA = +25°C R/C0113JA 5.0 mW/°C Operating Ambient Temperature Range TA −25 to +85 0 to +70 °C Operating Junction Temperature TJ(max) +150 +150 °C Storage Temperature Range Tstg −65 to +150 −65 to +150 °C Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected.
- Offset voltage, offset current and bias current specifications apply for a supply voltage range from a single 5.0 V supply up to ±15 V supplies.
- This rating applies for ±15 V supplies. The positive input voltage limit is 30 V above the negative supply. The negative input voltage limit is
equal to the negative supply voltage or 30 V below the positive supply, whichever is less.
- The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with a 1.0 mA
load. Thus, these parameters define an error band and take into account the “worst case” effects of voltage gain and input impedance.
- The response time specified is for a 100 mV input step with 5.0 mV overdrive.
- Do not short the strobe pin to ground; it should be current driven at 3.0 mA to 5.0 mA.
Figure 2. Circuit Schematic
are recommended, as shown in Figure 16. Figure 16. For the fastest response time, tie both balance pins resistors should be avoided. alternative to placing resistors close to the comparator. above 510 k/C0087 to maintain the same amount of hysteresis.
LM211, LM311 http://onsemi.com PACKAGE DIMENSIONS PDIP−8 N SUFFIX CASE 626−05 ISSUE L NOTES: 1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS). 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. F NOTE 2 −A− −B− −T− SEATING PLANE H J G D K N C L M MAM0.13 (0.005) B MT DIM MIN MAX MIN MAX INCHESMILLIMETERS A 9.40 10.16 0.370 0.400 B 6.10 6.60 0.240 0.260 C 3.94 4.45 0.155 0.175 D 0.38 0.51 0.015 0.020 F 1.02 1.78 0.040 0.070 G 2.54 BSC 0.100 BSC H 0.76 1.27 0.030 0.050 J 0.20 0.30 0.008 0.012 K 2.92 3.43 0.115 0.135 L 7.62 BSC 0.300 BSC N 0.76 1.01 0.030 0.040 /C0095/C0095
LM211, LM311 http://onsemi.com PACKAGE DIMENSIONS SOIC−8 D SUFFIX CASE 751−07 ISSUE AG SEATING PLANE N J X 45/C0095 K NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−07. A B S DH C 0.10 (0.004) DIM A MIN MAX MIN MAX INCHES 4.80 5.00 0.189 0.197 MILLIMETERS B 3.80 4.00 0.150 0.157 C 1.35 1.75 0.053 0.069 D 0.33 0.51 0.013 0.020 G 1.27 BSC 0.050 BSC H 0.10 0.25 0.004 0.010 J 0.19 0.25 0.007 0.010 K 0.40 1.27 0.016 0.050 M 0 8 0 8 N 0.25 0.50 0.010 0.020 S 5.80 6.20 0.228 0.244 −X− −Y− G MYM0.25 (0.010) −Z− YM0.25 (0.010) Z S X S M /C0095/C0095/C0095/C0095 1.52 0.060 7.0 0.275 0.6 0.024 1.270 0.050 4.0 0.155 /C0466mm inches/C0467SCALE 6:1 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. SOLDERING FOOTPRINT*
LM211, LM311 http://onsemi.com ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION N. American Technical Support: 800−282−9855 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Phone: 81−3−5773−3850 LM211/D LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative.