LM211D

LM111 TI | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 25

Technical content

LM111, LM211, LM311 DIFFERENTIAL COMPARATORS WITH STROBES SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003 1POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 /C0068 Fast Response Times /C0068 Strobe Capability /C0068 Maximum Input Bias Current. . . 300 nA /C0068 Maximum Input Offset Current. . . 70 nA /C0068 Can Operate From Single 5-V Supply /C0068 Available in Q-Temp Automotive – High-Reliability Automotive Applications – Configuration Control/Print Support – Qualification to Automotive Standards EMIT OUT IN+ IN– VCC– VCC+ COL OUT BAL/STRB BALANCE L M 1 1 1...J G PACKAGE LM211 . . . D, P, OR PW PACKAGE LM311 . . . D, P, PS, OR PW PACKAGE (TOP VIEW) 3 2 1 20 19 9 10 11 12 13 NC COL OUT NC BAL/STRB NC NC IN+ NC IN– NC L M 1 1 1...F K PACKAGE (TOP VIEW)NC EMIT OUT NC BALANCE NC NC NC NC CC–V CC+V NC – No internal connection description/ordering information The LM111, LM211, and LM311 are single high-speed voltage comparators. These devices are designed to operate from a wide range of power-supply voltages, including ±15-V supplies for operational amplifiers and 5-V supplies for logic systems. The output levels are compatible with most TTL and MOS circuits. These comparators are capable of driving lamps or relays and switching voltages up to 50 V at 50 mA. All inputs and outputs can be isolated from system ground. The outputs can drive loads referenced to ground, V CC+ or VCC– . Offset balancing and strobe capabilities are available, and the outputs can be wire-OR connected. If the strobe is low, the output is in the off state, regardless of the differential input. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright  2003, Texas Instruments IncorporatedPRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters.

LM111, LM211, LM311 DIFFERENTIAL COMPARATORS WITH STROBES SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003

2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

description/ordering information

ORDERING INFORMATION

AT 25°C PACKAGE † ORDERABLE PART NUMBER TOP-SIDE MARKING –0 C to 70C 7.5 mV PDIP (P) Tube of 50 LM311P LM311P –0 C to 70C 7.5 mV SOIC (D) Tube of 75 LM311D LM311 –0°C to 70°C 7.5 mV SOIC (D) Reel of 2500 LM311DR LM311 –0°C to 70°C 7.5 mV SOP (PS) Reel of 2000 LM311PSR L311 TSSOP (PW) Reel of 150 LM311PW L311TSSOP (PW) Tube of 2000 LM311PWR L311 –40 C to 85C 3 mV PDIP (P) Tube of 50 LM211P LM211P –40 C to 85C 3 mV SOIC (D) Tube of 75 LM211D LM211 –40°C to 85°C 3 mV SOIC (D) Reel of 2500 LM211DR LM211 TSSOP (PW) Reel of 150 LM211PW L211TSSOP (PW) Reel of 2000 LM211PWR L211 –40°C to 125°C 3 mV SOIC (D) Tube of 75 LM211QD LM211Q–40°C to 125°C 3 mV SOIC (D) Reel of 2500 LM211QDR LM211Q –55°C to 125°C 3 mV CDIP (JG) Tube of 50 LM111JG LM111JG –55°C to 125°C 3 mV LCCC (FK) Tube of 55 LM111FK LM111FK † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. functional block diagram BAL/STRB COL OUT IN– IN+ BALANCE EMIT OUT

LM111, LM211, LM311 DIFFERENTIAL COMPARATORS WITH STROBES SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003 3POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 schematic All resistor values shown are nominal. BAL/STRB BALANCE IN+ IN– 450 Ω 450 Ω 2.4 kΩ 1.2 kΩ 70 Ω 2.4 kΩ 1.2 kΩ 60 Ω 400 Ω 450 Ω 2 kΩ 200 Ω250 Ω 600 Ω 130 Ω 4 Ω 4 kΩ VCC+ VCC– EMIT OU T COL OUT 750 Ω 600 Ω Component Count Resistors 20 Diodes 2 EPI FET 1 Transistors 22

LM111, LM211, LM311 DIFFERENTIAL COMPARATORS WITH STROBES SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003

4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, unless otherwise noted, are with respect to the midpoint between VCC+ and VCC– . 2. Differential voltages are at IN+ with respect to IN–. 3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or ±15 V, whichever is less. 4. The output may be shorted to ground or either power supply. 5. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability. 6. The package thermal impedance is calculated in accordance with JESD 51-7. 7. Maximum power dissipation is a function of TJ(max), θJC, and TC . The maximum allowable power dissipation at any allowable case temperature is PD = (TJ(max) – TC )/θJC. Operating at the absolute maximum TJ of 150°C can affect reliability. 8. The package thermal impedance is calculated in accordance with MIL-STD-883. recommended operating conditions MIN MAX UNIT VCC+ – VCC– Supply voltage 3.5 30 V VI Input voltage (|VCC ±| ≤ 15 V) VCC– +0.5 VCC+ –1.5 V T Operating free-air temperature range LM111 –55 125 CTA Operating free-air temperature range LM211 –40 85 °CTA Operating free-air temperature range LM211Q –40 125 LM311 0 70

LM111, LM211, LM311 DIFFERENTIAL COMPARATORS WITH STROBES SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003 5POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA † LM111 LM211 LM211Q LM311 UNIT MIN TYP ‡ MAX MIN TYP ‡ MAX VIO Input offset voltageSee Note 6 25°C 0.7 3 2 7.5 mVVIO Input offset voltageSee Note 6 Full range 4 10 mV IIO Input offset currentSee Note 6 25°C 4 10 6 50 nAIIO Input offset currentSee Note 6 Full range 20 70 nA IIB Input bias currentVO = 1 V to 14 V 25°C 75 100 100 250 nAIIB Input bias currentVO = 1 V to 14 V Full range 150 300 nA IIL(S) Low-level strobe current (see Note 7) V(strobe) = 0.3 V,VID ≤ –10 mV 25°C –3 –3 mA VICR Common-mode input voltage range Full range to –14.5 13.8 to –14.7 to –14.5 13.8 to –14.7 V AVD Large-signal differential voltage amplification VO = 5 V to 35 V,R L = 1 kΩ 25°C 40 200 40 200 V/mV I High-level (collector) I(strobe) = –3 mA, VOH = 35 V, 25°C 0.2 10 nA IOH (collector) output leakage I(strobe) = –3 mA, VID = 5 mV VOH = 35 V, Full range 0.5 µAOH output leakage current VID = 5 mV, VOH = 35 V 25°C 0.2 50 nA V Low-level IOL = 50 mA VID = –5 mV 25°C 0.75 1.5 VV Low-level (collector-to-emitter) IOL = 50 mA VID = –10 mV 25°C 0.75 1.5 VVOL Low-level (collector-to-emitter) output voltage VCC+ = 4.5 V, VCC– = 0, VID = –6 mV Full range 0.23 0.4 V output voltage VCC– = 0, IOL = 8 mA VID = –10 mV Full range 0.23 0.4 ICC+ Supply current from VCC+ , output low VID = –10 mV, No load 25°C 5.1 6 5.1 7.5 mA ICC– Supply current from VCC– , output high VID = 10 mV, No load 25°C –4.1 –5 –4.1 –5 mA † Unless otherwise noted, all characteristics are measured with BALANCE and BAL/STRB open and EMIT OUT grounded. Full range for LM111 is –55°C to 125°C, for LM211 is –40°C to 85°C, for LM211Q is –40°C to 125°C, and for LM311 is 0°C to 70°C. ‡ All typical values are at TA = 25°C. NOTES: 9. The offset voltages and offset currents given are the maximum values required to drive the collector output up to 14 V or down to 1 V with a pullup resistor of 7.5 kΩ to VCC+ . These parameters actually define an error band and take into account the worst-case effects of voltage gain and input impedance. 10. The strobe should not be shorted to ground; it should be current driven at –3 mA to –5 mA (see Figures 13 and 27). switching characteristics, VCC ± = ±15 V, TA = 25°C PARAMETER TEST CONDITIONS LM111 LM211 LM211Q LM311 UNIT TYP Response time, low-to-high-level output R C = 500 Ω to 5 V, C L = 5 pF, See Note 8 115 ns Response time, high-to-low-level outputR C = 500 Ω to 5 V, C L = 5 pF, See Note 8 165 ns NOTE 11: The response time specified is for a 100-mV input step with 5-mV overdrive and is the interval between the input step function and the instant when the output crosses 1.4 V.

LM111, LM211, LM311 DIFFERENTIAL COMPARATORS WITH STROBES SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003

6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS † NOTE A: Condition 1 is with BALANCE and BAL/STRB open. Condition 2 is with BALANCE and BAL/STRB connected to VCC+ . Figure 1 –60 –40 –20 0 20 40 60 – Input Offset Current – nA INPUT OFFSET CURRENT vs FREE-AIR TEMPERATURE 80 100 120 140 TA – Free-Air Temperature – °C IIO LM311 Condition 2Condition 1 LM111 LM211 LM111 LM211 LM311 VCC ± = ±15 V VO = 1 V to 14 V See Note A NOTE A: Condition 1 is with BALANCE and BAL/STRB open. Condition 2 is with BALANCE and BAL/STRB connected to VCC+ . Figure 2 250 200 100 450 150 –60 –40 –20 0 20 40 60 – Input Bias Current – nA 350 300 400 500 80 100 120 140 IIB INPUT BIAS CURRENT vs FREE-AIR TEMPERATURE TA – Free-Air Temperature – °C LM311 LM311 LM111 LM211 Condition 2 VCC ± = ±15 V VO = 1 V to 14 V See Note A LM111 LM211 Condition 1 † Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

LM111, LM211, LM311 DIFFERENTIAL COMPARATORS WITH STROBES SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003 7POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TYPICAL CHARACTERISTICS † –1 –0.5 0 – Output Voltage – V VOLTAGE TRANSFER CHARACTERISTICS 0.5 1 VO VID – Differential Input Voltage – mV VID VCC+ = 30 V 1 kΩ Output VCC– VI = 50 V (LM111, LM211)

40 V (LM311)

VCC+ = 30 V 600 Ω VCC– Output COLLECTOR OUTPUT TRANSFER CHARACTERISTIC TEST CIRCUIT FOR FIGURE 3 EMITTER OUTPUT TRANSFER CHARACTERISTIC TEST CIRCUIT FOR FIGURE 3 Collector Output R L = 1 kΩ LM111 LM211 LM311 Emitter Output R L = 600 Ω VCC + = 30 V VCC– = 0 TA = 25°C Figure 3 † Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

LM111, LM211, LM311 DIFFERENTIAL COMPARATORS WITH STROBES SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003

8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

t – Time – ns 300 350 Differential Input Voltage – Output Voltage – VVO OUTPUT RESPONSE FOR VARIOUS INPUT OVERDRIVES 100 mV 20 mV 2 mV5 mV VCC ± = ±15 V R C = 500 Ω to 5 V TA = 25°C Figure 5 0 50 100 150 200 250 t – Time – ns OUTPUT RESPONSE FOR VARIOUS INPUT OVERDRIVES 300 350 Differential Input Voltage – Output Voltage – VVO 20 mV 5 mV 2 mV 100 mV VCC ± = ±15 V R C = 500 Ω to 5 V TA = 25°C VID VCC+ = 15 V 500 Ω VO VCC– = –15 V TEST CIRCUIT FOR FIGURES 4 AND 5 5 V

LM111, LM211, LM311 DIFFERENTIAL COMPARATORS WITH STROBES SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003

10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

– Output Current and Dissipation – mA 100 120 IO VCC ± = ±15 V t ≤ 10 s VID = –10 mV TA = 25°C VO – Output Voltage – V 140 160 300 200 100 – Output Dissipation – mW 400 500 600 PO 700 800 OUTPUT CURRENT AND DISSIPATION vs OUTPUT VOLTAGE PO (right scale) IO (left scale) Figure 9 051 0 TA = 25°C No Load VCC+ – Positive Supply Voltage – V VID = –10 mV POSITIVE SUPPLY CURRENT vs POSITIVE SUPPLY VOLTAGE ICC+ – Positive Supply Current – mA VID = 10 mV 0 –5 –10 –15 NEGATIVE SUPPLY CURRENT vs NEGATIVE SUPPLY VOLTAGE VCC– – Negative Supply Voltage – V ICC– – Negative Supply Current – mA VID = 10 mV or –10 mV TA = 25°C No Load Figure 10

LM111, LM211, LM311 DIFFERENTIAL COMPARATORS WITH STROBES SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003

12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

APPLICATION INFORMATION

† Resistor values shown are for a 0- to 30-V logic swing and a 15-V threshold. ‡ May be added to control speed and reduce susceptibility to noise spikes 5 V 1 kΩ 240 kΩ 82 kΩ 47 kΩ 82 kΩ Output to TTLInput† Figure 15. TTL Interface With High-Level Logic Figure 16. Detector for Magnetic Transducer Figure 17. 100-kHz Crystal Oscillator

LM111, LM211, LM311 DIFFERENTIAL COMPARATORS WITH STROBES SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003

14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

† Adjust to set clamp level 3.9 kΩ 30 kΩ† 1.5 µF VCC+ = 5 V Input From TTL2N2222 2N3708 Output 510 Ω 1 kΩ 1 kΩ 2N2222 2N2222 2.2 kΩ 1N914 1N914 2.7 kΩ Figure 22. Precision Squarer Figure 23. Digital Transmission Isolator Figure 24. Positive-Peak Detector

LM111, LM211, LM311 DIFFERENTIAL COMPARATORS WITH STROBES SLCS007H – SEPTEMBER 1973 – REVISED AUGUST 2003

16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

300 Ω VCC+ VCC– 100 kΩ Output 100 kΩ 47 Ω 10 kΩ 620 Ω Input 0.1 µF 300 Ω 620 Ω BAL/STRB BAL/STRB Figure 28. Switching Power Amplifier Figure 29. Switching Power Amplifiers

Orderable Device Status(1) Package Type Package Drawing Pins Package Qty Eco Plan(2) Lead/Ball FinishMSL Peak Temp (3) JM38510/10304BPA ACTIVE CDIP JG 8 1 None A42 SNPB Level-NC-NC-NC LM111FKB ACTIVE LCCC FK 20 1 None POST-PLATE Level-NC-NC-NC LM111JG ACTIVE CDIP JG 8 1 None A42 SNPB Level-NC-NC-NC LM111JGB ACTIVE CDIP JG 8 1 None A42 SNPB Level-NC-NC-NC LM211D ACTIVE SOIC D 8 75 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM LM211DR ACTIVE SOIC D 8 2500 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM LM211P ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC LM211PW ACTIVE TSSOP PW 8 150 Pb-Free (RoHS) CU NIPDAU Level-1-250C-UNLIM LM211PWR ACTIVE TSSOP PW 8 2000 Pb-Free (RoHS) CU NIPDAU Level-1-250C-UNLIM LM211QD ACTIVE SOIC D 8 75 Pb-Free (RoHS) CU NIPDAU Level-2-250C-1 YEAR/ Level-1-235C-UNLIM LM211QDR ACTIVE SOIC D 8 2500 Pb-Free (RoHS) CU NIPDAU Level-2-250C-1 YEAR/ Level-1-235C-UNLIM LM311D ACTIVE SOIC D 8 75 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM LM311DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM311P ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC LM311PSR ACTIVE SO PS 8 2000 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM LM311PW ACTIVE TSSOP PW 8 150 Pb-Free (RoHS) CU NIPDAU Level-1-250C-UNLIM LM311PWLE OBSOLETE TSSOP PW 8 None Call TI Call TI LM311PWR ACTIVE TSSOP PW 8 2000 Pb-Free (RoHS) CU NIPDAU Level-1-250C-UNLIM LM311Y OBSOLETE XCEPT Y 0 None Call TI Call TI (1)The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2)Eco Plan - May not be currently available - please checkhttp://www.ti.com/productcontentfor the latest availability information and additional product content details. None: Not yet available Lead (Pb-Free). Pb-Free (RoHS):TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br):TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens, including bromine (Br) or antimony (Sb) above 0.1% of total product weight. (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder PACKAGE OPTION ADDENDUM www.ti.com 25-Feb-2005 Addendum-Page 1

temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. PACKAGE OPTION ADDENDUM www.ti.com 25-Feb-2005 Addendum-Page 2

MCER001A – JANUARY 1995 – REVISED JANUARY 1997 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE 0.310 (7,87) 0.290 (7,37) 0.014 (0,36) 0.008 (0,20) Seating Plane 4040107/C 08/96 0.065 (1,65) 0.045 (1,14) 0.020 (0,51) MIN 0.400 (10,16) 0.355 (9,00) 0.015 (0,38) 0.023 (0,58) 0.063 (1,60) 0.015 (0,38) 0.200 (5,08) MAX 0.130 (3,30) MIN 0.245 (6,22) 0.280 (7,11) 0.100 (2,54) 0°–15° NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. This package can be hermetically sealed with a ceramic lid using glass frit. D. Index point is provided on cap for terminal identification. E. Falls within MIL STD 1835 GDIP1-T8

MLCC006B – OCTOBER 1996 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER 4040140/D 10/96

28 TERMINAL SHOWN

B 0.358 (9,09) MAX (11,63) 0.560 (14,22) 0.560 0.458 0.858 (21,8) 1.063 (27,0) (14,22) ANO. OF MINMAX 0.358 0.660 0.761 0.458 0.342 (8,69) MIN (11,23) (16,26) 0.640 0.739 0.442 (9,09) (11,63) (16,76) 0.962 1.165 (23,83) 0.938 (28,99) 1.141 (24,43) (29,59) (19,32)(18,78) 0.020 (0,51) TERMINALS 0.080 (2,03) 0.064 (1,63) (7,80) 0.307 (10,31) 0.406 (12,58) 0.495 (12,58) 0.495 (21,6) 0.850 (26,6) 1.047 0.045 (1,14) 0.045 (1,14) 0.035 (0,89) 0.035 (0,89) 0.010 (0,25) 121314151618 17 432 0.020 (0,51) 0.010 (0,25) 12826 27 B SQ A SQ 0.055 (1,40) 0.045 (1,14) 0.028 (0,71) 0.022 (0,54) 0.050 (1,27) NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. This package can be hermetically sealed with a metal lid. D. The terminals are gold plated. E. Falls within JEDEC MS-004

MPDI001A – JANUARY 1995 – REVISED JUNE 1999 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 P (R-PDIP-T8) PLASTIC DUAL-IN-LINE 0.015 (0,38) Gage Plane 0.325 (8,26) 0.300 (7,62) 0.010 (0,25) NOM MAX 0.430 (10,92) 4040082/D 05/98 0.200 (5,08) MAX 0.125 (3,18) MIN 0.355 (9,02) 0.020 (0,51) MIN 0.070 (1,78) MAX 0.240 (6,10) 0.260 (6,60) 0.400 (10,60) 0.015 (0,38) 0.021 (0,53) Seating Plane M0.010 (0,25) 0.100 (2,54) NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001 For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm

MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE

14 PINS SHOWN

0,65 M0,10 0,10 0,25 0,50 0,75 0,15 NOM Gage Plane 9,80 9,60 7,90 7,70 2016 6,60 6,40 4040064/F 01/97 0,30 6,60 6,20 0,19 4,30 4,50 0,15 A 1,20 MAX 5,10 4,90 3,10 2,90 A MAX A MIN DIM PINS ** 0,05 4,90 5,10 Seating Plane 0°–8° NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Body dimensions do not include mold flash or protrusion not to exceed 0,15. D. Falls within JEDEC MO-153

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright  2005, Texas Instruments Incorporated