Amplifier

LM101AWLQMLV

Texas Instruments

LM101AQML Operational Amplifiers

Manufacturer: Texas Instruments

Document: 25 Pages / 992Kb

Request Quote Download Datasheet Read online HTML view

More from Texas Instruments Browse L parts

Online Datasheet

Read LM101AWLQMLV online.

LM101AQML TI1 | Alldatasheet

Document overview

Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 25

Technical content

LM101AQML Operational Amplifiers Literature Number: SNOSAI0

The LM101A is a general purpose operational amplifier which features improved performance over industry stan- dards such as the LM709. Advanced processing techniques make possible an order of magnitude reduction in input currents, and a redesign of the biasing circuitry reduces the temperature drift of input current. Improved specifications include: Offset voltage 3 mV maximum over temperature Input current 100 nA maximum over temperature Offset current 20 nA maximum over temperature Guaranteed drift characteristics Offsets guaranteed over entire common mode and sup- ply voltage ranges Slew rate of 10V/µs as a summing amplifier This amplifier offers many features which make its appli- cation nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, and freedom from oscillations and compensa- tion with a single 30 pF capacitor. It has advantages over internally compensated amplifiers in that the frequency compensation can be tailored to the particular applica- tion. For example, in low frequency circuits it can be overcompensated for increased stability margin. Or the compensation can be optimized to give more than a factor of ten improvement in high frequency performance for most applications. In addition, the device provides better accuracy and lower noise in high impedance circuitry. The low input currents also make it particularly well suited for long interval integrators or timers, sample and hold circuits and low frequency waveform generators. Further, replac- ing circuits where matched transistor pairs buffer the inputs of conventional IC op amps, it can give lower offset voltage and a drift at a lower cost.

Features

n Available with radiation guarantee n Offset voltage 3 mV maximum over temperature n Input current 100 nA maximum over temperature n Offset current 20 nA maximum over temperature n Guaranteed drift characteristics n Offsets guaranteed over entire common mode and supply voltage ranges n Slew rate of 10 V/µS as a summing amplifier

Ordering Information

NS Part Number SMD Part Number NS Package Number Package Description LM101AH/883 H08C 8LD Metal Can LM101AJ/883 J08A 8LD CERDIP LM101AW/883 W10A 10LD CERPACK LM101AH-QMLV 5962–9951501VGA H08C 8LD Metal Can LM101AHLQMLV 5962L9951501VGA 50k rd(Si) H08C 8LD Metal Can LM101AHRQMLV 5962R9951501VGA 100k rd(Si) H08C 8LD Metal Can LM101AJLQMLV 5962L9951501VPA 50k rd(Si) J08A 8LD CERDIP LM101AJ-QMLV 5962–9951501VPA J08A 8LD CERDIP LM101AW-QMLV 5962–9951501VHA W10A 10LD CERPACK LM101AWLQMLV 5962L9951501VHA 50k rd(Si) W10A 10LD CERPACK January 2006 LM101AQML Operational Amplifiers © 2006 National Semiconductor Corporation DS201223 www.national.com

Schematic (Note 11) 20122301 Connection Diagrams (Top View) Metal Can Package 20122302 See NS Package Number H08C Note: Pin 4 connected to case. (Top View) Dual-In-Line Package 20122304 See NS Package Number J08A LM101AQML www.national.com 2

Connection Diagrams (Continued) (Top View) Ceramic Flatpack Package 20122340 See NS Package Number W10A Fast AC/DC Converter 20122333 Note 1: Feedforward compensation can be used to make a fast full wave rectifier without a filter. LM101AQML www.national.com3

Absolute Maximum Ratings(Note 2) Supply Voltage ±22V Differential Input Voltage ±30V Input Voltage (Note 3) ±15V Output Short Circuit Duration Continuous Operating Ambient Temp. Range −55˚C ≤ T A ≤ +125˚C TJ Max 150˚C Power Dissipation at T A = 25˚C (Note 4) H-Package (Still Air) 750 mW (500 LF / Min Air Flow) 1200 mW J-Package (Still Air) 1000 mW (500 LF / Min Air Flow) 1500 mW W-Package (Still Air) 500mW (500 LF / Min Air Flow) 800mW Thermal Resistance θJA H-Package (Still Air) 165˚C/W (500 LF / Min Air Flow) 89˚C/W J-Package (Still Air) 128˚C/W (500 LF / Min Air Flow) 75˚C/W W-Package (Still Air) 233˚C/W (500 LF / Min Air Flow) 155˚C/W θJC (Typical) H-Package 39˚C/W J-Package 26˚C/W W-Package 26˚C/W Storage Temperature Range −65˚C ≤ TA ≤ +150˚C Lead Temperature (Soldering, 10 sec.) 300˚C ESD Tolerance (Note 5) 3000V LM101AQML www.national.com 4

Quality Conformance Inspection Mil-Std-883, Method 5005 - Group A Subgroup Description Temp (˚C)

1 Static tests at 25

2 Static tests at 125

3 Static tests at -55

4 Dynamic tests at 25

5 Dynamic tests at 125

6 Dynamic tests at -55

7 Functional tests at 25

8A Functional tests at 125 8B Functional tests at -55

9 Switching tests at 25

10 Switching tests at 125

11 Switching tests at -55

The following conditions apply to all parameters, unless otherwise specified VCC = ±20V, VCM=0 V Symbol Parameter Conditions Notes Min Max Units Sub- groups VIO Input Offset Voltage V CM = -15V, RS =5 0Ω -2.0 2.0 mV 1 -3.0 3.0 mV 2, 3 VCM = 15V, RS =5 0Ω -2.0 2.0 mV 1 -3.0 3.0 mV 2, 3 RS =5 0Ω -2.0 2.0 mV 1 -3.0 3.0 mV 2, 3 VCC = ±5V, RS =5 0Ω -2.0 2.0 mV 1 -3.0 3.0 mV 2, 3 IIO Input Offset Current V CM = -15V -10 10 nA 1 -20 20 nA 2, 3 VCM = 15V -10 10 nA 1 -20 20 nA 2, 3 -10 10 nA 1 -20 20 nA 2, 3 V CC = ±5V -10 10 nA 1 -20 20 nA 2, 3 ±IIB Input Bias Current V CM = -15V 1.0 75 nA 1 1.0 100 nA 2, 3 VCM = 15V 1.0 75 nA 1 1.0 100 nA 2, 3 1.0 75 nA 1 1.0 100 nA 2, 3 V CC = ±5V 1.0 75 nA 1 1.0 100 nA 2, 3 PSRR+ Power Supply Rejection Ratio +V CC = +20V and +5V, -VCC=-20V, RS=50Ω 80 dB 1, 2, 3 PSRR- Power Supply Rejection Ratio +V CC = +20V, -VCC= -20V and -5V, R S=50Ω 80 dB 1, 2, 3 CMRR Common Mode Rejection Ratio -15V ≤ VCM ≤ 15V, RS =5 0Ω 80 dB 1, 2, 3 LM101AQML www.national.com5

DC Parameters (Continued) The following conditions apply to all parameters, unless otherwise specified VCC = ±20V, VCM=0 V Symbol Parameter Conditions Notes Min Max Units Sub- groups ICC Supply Current 3.0 mA 1 2.5 mA 2 3.5 mA 3 IO Adj Input Offset Voltage Adjust 4.0 mV 1, 2, 3 −VIO Adj Input Offset Voltage Adjust -4.0 mV 1, 2, 3 +IOS Short Circuit Current -45 -7.0 mA 1, 2, 3 -IOS Short Circuit Current 7.0 45 mA 1, 2, 3 VI Input Voltage Range V CC = ±20V (Note 6) -15 15 V 1, 2, 3 +AVS Large Signal Gain V CC = ±15V, RS =0 ,R L=2KΩ, VO =10V

50 V/mV 4

25 V/mV 5, 6

-AVS Large Signal Gain V CC = ±15V, RS =0 ,R L=2KΩ, VO =-10V RI Input Resistance (Note 7) 1.5 M Ω 4 (Note 7) 0.5 M Ω 5, 6 +VOP Output Voltage Swing R L = 10KΩ 1 6 V 4 ,5 ,6 RL =2 KΩ 1 5 V 4 ,5 ,6 RL = 10KΩ,V CC = ±15V 12 V 4, 5, 6 RL =2 KΩ,V CC = ±15V 10 V 4, 5, 6 -VOP Output Voltage Swing R L = 10KΩ - 1 6 V 4 ,5 ,6 RL =2 KΩ - 1 5 V 4 ,5 ,6 RL = 10KΩ,V CC = ±15V -12 V 4, 5, 6 RL =2 KΩ,V CC = ±15V -10 V 4, 5, 6 AC Parameters The following conditions apply to all parameters, unless otherwise specified VCC = ±20V, RL =2 KΩ,A V =1 Symbol Parameter Conditions Notes Min Max Units Sub- groups +SR Slew Rate V I = -5V to 5V 0.2 V/µS 7 -SR Slew Rate V I = 5V to -5V 0.2 V/µS 7 GBW Gain Bandwidth V I = 50mVRMS, f = 20KHz 0.25 MHz 7 LM101AQML www.national.com 6

LM101A QML & RH Electrical Characteristics(Note 10) DC Parameters The following conditions apply to all parameters, unless otherwise specified VCC = ±20V, VCM = 0V, RS =5 0Ω Symbol Parameter Conditions Notes Min Max Units Sub- groups VIO Input Offset Voltage +V CC = 35V, -VCC = -5V, VCM = -15V -2.0 +2.0 mV 1 -3.0 +3.0 mV 2, 3 +VCC = 5V, -VCC = -35V, VCM = +15V -2.0 +2.0 mV 1 -3.0 +3.0 mV 2, 3 VCM = 0V -2.0 +2.0 mV 1 -3.0 +3.0 mV 2, 3 +VCC = 5V, -VCC = -5V, VCM =0 V -2.0 +2.0 mV 1 -3.0 +3.0 mV 2, 3 IIO Input Offset Current +V CC = 35V, -VCC = -5V, VCM = -15V, RS = 100KΩ -10 +10 nA 1, 2 -20 +20 nA 3 +VCC = 5V, -VCC = -35V, VCM = +15V, RS = 100KΩ -10 +10 nA 1, 2 -20 +20 nA 3 VCM = 0V, RS = 100KΩ -10 +10 nA 1, 2 -20 +20 nA 3 +VCC = 5V, -VCC = -5V, VCM = 0V, RS = 100KΩ -10 +10 nA 1, 2 -20 +20 nA 3 ±IIB Input Bias Current +V CC = 35V, -VCC = -5V, VCM = -15V, RS = 100KΩ -0.1 75 nA 1, 2 -0.1 100 nA 3 +VCC = 5V, -VCC = -35V, VCM = +15V, RS = 100KΩ -0.1 75 nA 1, 2 -0.1 100 nA 3 VCM = 0V, RS = 100KΩ -0.1 75 nA 1, 2 -0.1 100 nA 3 +VCC = 5V, -VCC = -5V, VCM = 0V, RS = 100KΩ -0.1 75 nA 1, 2 -0.1 100 nA 3 +PSRR Power Supply Rejection Ratio +V CC = 10V, -VCC = -20V -50 +50 µV/V 1 -100 +100 µV/V 2, 3 -PSRR Power Supply Rejection Ratio +V CC = 20V, -VCC = -10V -50 +50 µV/V 1 -100 +100 µV/V 2, 3 CMRR Common Mode Rejection Ratio V CC = ±35V to ±5V, VCM = ±15V 80 dB 1, 2, 3 +VIO Adj Adjustment for Input Offset Voltage 4.0 mV 1, 2, 3 -VIO Adj Adjustment for Input Offset Voltage -4.0 mV 1, 2, 3 +IOS Output Short Circuit Current +V CC = 15V, -VCC = -15V, t ≤ 25mS, VCM = -15V -60 mA 1, 2, 3 -IOS Output Short Circuit Current +V CC = 15V, -VCC = -15V, t ≤ 25mS, VCM = +15V +60 mA 1, 2, 3 ICC Power Supply Current +V CC = 15V, -VCC = -15V 3.0 mA 1 2.32 mA 2 3.5 mA 3 ∆VIO/ ∆T Temperature Coefficient of Input Offset Voltage -55˚C ≤ TA ≤ +25˚C (Note 8) -18 +18 µV/˚C 2 +25˚C ≤ TA ≤ +125˚C (Note 8) -15 +15 uV/˚C 3 ∆ IIO / ∆T Temperature Coefficient of Input Offset Current LM101AQML www.national.com7

LM101A QML & RH Electrical Characteristics(Note 10) (Continued) DC Parameters (Continued) The following conditions apply to all parameters, unless otherwise specified VCC = ±20V, VCM = 0V, RS =5 0Ω Symbol Parameter Conditions Notes Min Max Units Sub- groups -AVS Large Signal (Open Loop) Voltage Gain RL =2 KΩ,V O = -15V (Note 9) 50 V/mV 4 (Note 9) 25 V/mV 5, 6 RL = 10KΩ,V O = -15V (Note 9) 50 V/mV 4 (Note 9) 25 V/mV 5, 6 +AVS Large Signal (Open Loop) Voltage Gain RL =2 KΩ,V O = +15V (Note 9) 50 V/mV 4 (Note 9) 25 V/mV 5, 6 RL = 10KΩ,V O = +15V (Note 9) 50 V/mV 4 (Note 9) 25 V/mV 5, 6 AVS Large Signal (Open Loop) Voltage Gain VCC = ±5V,RL =2 KΩ, VO = ±2V (Note 9) 10 V/mV 4,5, 6 VCC = ±5V, RL = 10KΩ, VO = ±2V (Note 9) 10 V/mV 4,5, 6 +VOP Output Voltage Swing R L = 10KΩ,V CM = -20V +16 V 4,5, 6 R L=2 KΩ,V CM = -20V +15 V 4,5, 6 -VOP Output Voltage Swing R L = 10KΩ,V CM = 20V -16 V 4,5, 6 RL =2 KΩ,V CM = 20V -15 V 4,5, 6 AC Parameters The following conditions apply to all parameters, unless otherwise specified VCC = ±20V, VCM = 0V, RS =5 0Ω Symbol Parameter Conditions Notes Min Max Units Sub- groups +SR Slew Rate A V =1 ,V I = -5V to +5V 0.3 V/µS 7, 8A

0.2 V/µS 8B

-SR Slew Rate A V =1 ,V I = +5V to -5V 0.3 V/µS 7, 8A TRTR Rise Time A V =1 ,V I = 50mV 800 nS 7, 8A, 8B TROS Overshoot A V =1 ,V I = 50mV 25 % 7 35 % 8A, 8B NIBB Noise Broadband BW = 10Hz to 5KHz, R S =0 Ω 15 µV RMS 7 NIPC Noise Popcorn BW = 10Hz to 5KHz, RS = 100KΩ 80 µV PK 7 DC Parameters Drift Values The following conditions apply to all parameters, unless otherwise specified VCC = ±20V, VCM = 0V, RS =5 0Ω Delta calculations performed on QMLV devices at group B, Subgroup 5 only. Symbol Parameter Conditions Notes Min Max Units Sub- groups VIO Input Offset Voltage V CM = 0V -0.5 0.5 mV 1 ± IIB Input Bias Current V CM = 0V, RS = 100KΩ -7.5 7.5 nA 1 LM101AQML www.national.com 8

Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which the device is intended to be functional, but do no guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated u nder the listed test conditions. Note 3: For supply voltages less than ±15V, the absolute maximum input voltage is equal to the supply voltage. Note 4: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature), θJA (package junction to ambient thermal resistance), and T A (ambient temperature). The maximum allowable power dissipation at any temperature is P Dmax =( TJmax −T A)/ θJA or the number given in the Absolute Maximum Ratings, whichever is lower. Note 5: Human body model, 100 pF discharged through 1.5 k Ω. Note 6: Parameter guaranteed by the input conditions of several DC parameters Note 7: Parameter guaranteed, not tested. Note 8: Calculated parameter Note 9: Datalog reading of K = V/mV. Note 10: Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics. These parts may be dose rate sensitive in a sp ace environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters are guaranteed only for the conditions as specified in Mil-Std-883, Method 1019 Note 11: Pin connections shown are for 8-pin packages. LM101AQML www.national.com9

Typical Performance Characteristics LM101A Input Voltage Range Output Swing 20122341 20122342 Voltage Gain 20122343 Supply Current Voltage Gain 20122347 20122348 LM101AQML www.national.com 10

Typical Performance Characteristics LM101A (Continued) Maximum Power Dissipation Input Current, LM101A 20122349 20122350 Current Limiting Input Noise Voltage 20122351 20122352 Input Noise Current Common Mode Rejection 20122353 20122354 LM101AQML www.national.com11

Typical Performance Characteristics LM101A (Continued) Power Supply Rejection Closed Loop Output Impedance 20122355 20122356 LM101AQML www.national.com 12

Typical Performance Characteristics for Various Compensation Circuits (Note 11) Single Pole Compensation Two Pole Compensation 20122308 CS=3 0p F 20122312 CS=3 0p F C 2=1 0C 1 Feedforward Compensation Open Loop Frequency Response 20122316 fo= 3 MHz 20122309 Open Loop Frequency Response Open Loop Frequency Response 20122313 20122317 LM101AQML www.national.com13

Typical Performance Characteristics for Various Compensation Circuits (Note 11) (Continued) Large Signal Frequency Response Large Signal Frequency Response 20122310 20122314 Large Signal Frequency Response Voltage Follower Pulse Response 20122318 20122311 Voltage Follower Pulse Response Inverter Pulse Response 20122315 20122319 LM101AQML www.national.com 14

Typical Applications (Note 11) Variable Capacitance Multiplier 20122320 Simulated Inductor 20122321 L . R1 R2 C1 RS =R 2 RP =R 1 Fast Inverting Amplifier with High Input Impedance 20122322 Inverting Amplifier with Balancing Circuit 20122323 †May be zero or equal to parallel combination of R1 and R2 for minimum offset. Sine Wave Oscillator 20122324 fo =1 0k H z Integrator with Bias Current Compensation 20122325 *Adjust for zero integrator drift. Current drift typically 0.1 nA/˚C over −55˚C to +125˚C temperature range. LM101AQML www.national.com15

Application Hints(Note 11) Protecting Against Gross Fault Conditions 20122326 *Protects input †Protects output ‡Protects output — not needed when R4 is used. Compensating for Stray Input Capacitances or Large Feedback Resistor 20122327 Isolating Large Capacitive Loads 20122328 LM101AQML www.national.com 16

Although the LM101A is designed for trouble free operation, experience has indicated that it is wise to observe certain precautions given below to protect the devices from abnor- mal operating conditions. It might be pointed out that the advice given here is applicable to practically any IC op amp, although the exact reason why may differ with different de- vices. When driving either input from a low-impedance source, a limiting resistor should be placed in series with the input lead to limit the peak instantaneous output current of the source to something less than 100 mA. This is especially important when the inputs go outside a piece of equipment where they could accidentally be connected to high voltage sources. Large capacitors on the input (greater than 0.1 µF) should be treated as a low source impedance and isolated with a resistor. Low impedance sources do not cause a problem unless their output voltage exceeds the supply voltage. How- ever, the supplies go to zero when they are turned off, so the isolation is usually needed. The output circuitry is protected against damage from shorts to ground. However, when the amplifier output is connected to a test point, it should be isolated by a limiting resistor, as test points frequently get shorted to bad places. Further, when the amplifer drives a load external to the equipment, it is also advisable to use some sort of limiting resistance to preclude mishaps. Precautions should be taken to insure that the power sup- plies for the integrated circuit never become reversed — even under transient conditions. With reverse voltages greater than 1V, the IC will conduct excessive cur- rent, fusing internal aluminum interconnects. If there is a possibility of this happening, clamp diodes with a high peak current rating should be installed on the supply lines. Rever- sal of the voltage between V + and V− will always cause a problem, although reversals with respect to ground may also give difficulties in many circuits. The minimum values given for the frequency compensation capacitor are stable only for source resistances less than 10 kΩ, stray capacitances on the summing junction less than 5 pF and capacitive loads smaller than 100 pF. If any of these conditions are not met, it becomes necessary to over- compensate the amplifier with a larger compensation capaci- tor. Alternately, lead capacitors can be used in the feedback network to negate the effect of stray capacitance and large feedback resistors or an RC network can be added to isolate capacitive loads. Although the LM101A is relatively unaffected by supply by- passing, this cannot be ignored altogether. Generally it is necessary to bypass the supplies to ground at least once on every circuit card, and more bypass points may be required if more than five amplifiers are used. When feed-forward compensation is employed, however, it is advisable to by- pass the supply leads of each amplifier with low inductance capacitors because of the higher frequencies involved. Typical Applications (Note 11) Standard Compensation and Offset Balancing Circuit 20122329 Fast Voltage Follower 20122331 Power Bandwidth: 15 kHz Slew Rate: 1V/µs Fast Summing Amplifier 20122330 Power Bandwidth: 250 kHz Small Signal Bandwiidth: 3.5 MHz Slew Rate: 10V/µs LM101AQML www.national.com17

Typical Applications(Note 11) (Continued) Bilateral Current Source 20122332 R 3=R 4+R 5 R 1=R 2 Fast AC/DC Converter(Note 12) 20122333 Note 12: Feedforward compensation can be used to make a fast full wave rectifier without a filter. LM101AQML www.national.com 18

Typical Applications(Note 11) (Continued) Instrumentation Amplifier 20122334 R1 = R4; R2 = R3 *,† Matching determines CMRR. Integrator with Bias Current Compensation 20122335 *Adjust for zero integrator drift. Current drift typically 0.1 nA/˚C over 0˚C to +70˚C temperature range. Voltage Comparator for Driving RTL Logic or High Current Driver 20122337 LM101AQML www.national.com19

Typical Applications(Note 11) (Continued) Low Frequency Square Wave Generator 20122336 Low Drift Sample and Hold 20122338 *Polycarbonate-dielectric capacitor Voltage Comparator for Driving DTL or TTL Integrated Circuits 20122339 LM101AQML www.national.com 20

Revision Section Originator Changes 01/05/06 A New Release to corporate format L. Lytle 2 MDS datasheets converted into one Corp. datasheet format. MNLM101A-X Rev 0A0 and MRLM101A-X-RH rev 1C2 MDS datasheets will be archived. LM101AQML www.national.com21

Physical Dimensions inches (millimeters) unless otherwise noted Metal Can Package (H) Ceramic Dual-In-Line Package (J) LM101AQML www.national.com 22

Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Ceramic Flatpack Package (W) National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 www.national.com LM101AQML Operational Amplifiers

Texas InstrumentsIncorporatedand itssubsidiaries(TI)reservetherighttomake corrections,modifications,enhancements,improvements, and otherchanges toitsproductsand servicesatany timeand todiscontinueany productorservicewithoutnotice.Customersshould obtainthelatestrelevantinformationbeforeplacingordersand shouldverifythatsuch informationiscurrentand complete.Allproductsare soldsubjecttoTI’s termsand conditionsofsalesuppliedatthetimeoforderacknowledgment. TIwarrantsperformanceofitshardwareproductstothespecificationsapplicableatthetimeofsaleinaccordancewithTI’s standard warranty.Testingand otherqualitycontroltechniquesareused totheextentTIdeems necessarytosupportthiswarranty.Exceptwhere mandated by governmentrequirements,testingofallparametersofeach productisnotnecessarilyperformed. TIassumes no liabilityforapplicationsassistanceorcustomerproductdesign.Customersareresponsiblefortheirproductsand applicationsusingTIcomponents.To minimizetherisksassociatedwithcustomerproductsand applications,customersshouldprovide adequatedesignand operatingsafeguards. TIdoes notwarrantorrepresentthatany license,eitherexpressorimplied,isgrantedunderany TIpatentright,copyright,mask work right, orotherTIintellectualpropertyrightrelatingtoany combination,machine,orprocessinwhichTIproductsorservicesareused.Information publishedby TIregardingthird-partyproductsorservicesdoes notconstitutea licensefromTItouse such productsorservicesora warrantyorendorsementthereof.Use ofsuch informationmay requirea licensefroma thirdpartyunderthepatentsorotherintellectual propertyofthethirdparty,ora licensefromTIunderthepatentsorotherintellectualpropertyofTI. ReproductionofTIinformationinTIdatabooks ordatasheetsispermissibleonlyifreproductioniswithoutalterationand isaccompanied by allassociatedwarranties,conditions,limitations,and notices.Reproductionofthisinformationwithalterationisan unfairand deceptive businesspractice.TIisnotresponsibleorliableforsuch altereddocumentation.Informationofthirdpartiesmay be subjecttoadditional restrictions. ResaleofTIproductsorserviceswithstatementsdifferentfromorbeyond theparametersstatedby TIforthatproductorservicevoidsall expressand any impliedwarrantiesfortheassociatedTIproductorserviceand isan unfairand deceptivebusinesspractice.TIisnot responsibleorliableforany such statements. TIproductsarenotauthorizedforuse insafety-criticalapplications(suchas lifesupport)where a failureoftheTIproductwouldreasonably be expectedtocause severepersonalinjuryordeath,unlessofficersofthepartieshave executedan agreementspecificallygoverning such use.Buyersrepresentthattheyhave allnecessaryexpertiseinthesafetyand regulatoryramificationsoftheirapplications,and acknowledgeand agreethattheyaresolelyresponsibleforalllegal,regulatoryand safety-relatedrequirementsconcerningtheirproducts and any use ofTIproductsinsuch safety-criticalapplications,notwithstandingany applications-relatedinformationorsupportthatmay be providedby TI.Further,Buyersmust fullyindemnifyTIand itsrepresentativesagainstany damages arisingoutoftheuse ofTIproductsin such safety-criticalapplications. TIproductsareneitherdesignednorintendedforuse inmilitary/aerospaceapplicationsorenvironmentsunlesstheTIproductsare specificallydesignatedby TIas military-gradeor"enhanced plastic." Onlyproductsdesignatedby TIas military-grademeet military specifications.Buyersacknowledgeand agreethatany such use ofTIproductswhichTIhas notdesignatedas military-gradeissolelyat theBuyer's risk,and thattheyaresolelyresponsibleforcompliancewithalllegaland regulatoryrequirementsinconnectionwithsuch use. TIproductsareneitherdesignednorintendedforuse inautomotiveapplicationsorenvironmentsunlessthespecificTIproductsare designatedby TIas compliantwithISO/TS 16949 requirements.Buyersacknowledgeand agreethat,iftheyuse any non-designated productsinautomotiveapplications,TIwillnotbe responsibleforany failuretomeet such requirements. FollowingareURLs where you can obtaininformationon otherTexas Instrumentsproductsand applicationsolutions: Products Applications Audio www.ti.com/audio Communicationsand Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP ® Products www.dlp.com Energyand Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocksand Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space,Avionicsand Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportationand Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Videoand Imaging www.ti.com/video RFID www.ti-rfid.com OMAP MobileProcessors www.ti.com/omap WirelessConnectivity www.ti.com/wirelessconnectivity TIE2E Community Home Page e2e.ti.com MailingAddress:Texas Instruments,PostOfficeBox 655303,Dallas,Texas 75265 Copyright© 2011,Texas InstrumentsIncorporated

Product Information

LM101AWLQMLV specifications and overview.

Summary

LM101AQML Operational Amplifiers

Description

LM101AQML Operational Amplifiers

Source title LM101AWLQMLV Datasheet(PDF) - Texas Instruments

Related Parts

More parts from the same family.

Browse manufacturer