LF444ACN

LF444 NSC | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 10

Technical content

Features

n 1⁄4 supply current of a LM148: 200 µA/Amplifier (max) n Low input bias current: 50 pA (max) n High gain bandwidth: 1 MHz n High slew rate: 1 V/µs n Low noise voltage for low power n Low input noise current n High input impedance: 1012Ω n High gain VO = ±10V, RL = 10k: 50k (min) Simplified Schematic

Ordering Information

X indicates electrical grade Y indicates temperature range “M” for military, “C” for commercial Z indicates package type “D”, “M” or “N” Connection Diagram BI-FET™ and BI-FET II™ are trademarks of National Semiconductor Corporation. 1/4 Quad DS009156-1 Dual-In-Line Package DS009156-2 Top View Order Number LF444AMD, LF444CM, LF444ACN, LF444CN or LF444MD/883 See NS Package Number D14E, M14A or N14A May 1998 LF444 Quad Low Power JFET Input Operational Amplifier © 1999 National Semiconductor Corporation DS009156 www.national.com

Absolute Maximum Ratings(Note 11) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. LF444A LF444 Supply Voltage ±22V ±18V Differential Input Voltage ±38V ±30V Input Voltage Range ±19V ±15V (Note 1) Output Short Circuit Continuous Continuous Duration (Note 2) D Package N, M Packages Power Dissipation 900 mW 670 mW (Notes 3, 9) Tjmax 150˚C 115˚C θjA (Typical) 100˚C/W 85˚C/W LF444A/LF444 Operating Temperature Range (Note 4) Storage Temperature Range −65˚C ≤ T A ≤ 150˚C ESD Tolerance (Note 10) Rating to be determined Soldering Information Dual-In-Line Packages (Soldering, 10 sec.) 260˚C Small Outline Package Vapor Phase (60 sec.) 215˚C Infrared (15 sec.) 220˚C See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” for other methods of soldering surface mount devices. Symbol Parameter Conditions LF444A LF444 Units Min Typ Max Min Typ Max VOS Input Offset Voltage R S = 10k, TA = 25˚C 2 5 3 10 mV 0˚C ≤ TA ≤ +70˚C 6.5 12 mV ΔVOS /ΔT Average TC of Input R S = 10 kΩ 10 10 µV/˚C Offset Voltage IOS Input Offset Current V S = ±15V T j = 25˚C 5 25 5 50 pA (Notes 5, 6) T j = 70˚C 1.5 1.5 nA Tj = 125˚C 10 nA IB Input Bias Current V S = ±15V T j = 25˚C 10 50 10 100 pA (Notes 5, 6) T j = 70˚C 3 3 nA Tj = 125˚C 20 nA R IN Input Resistance T j = 25˚C 10 12 1012 Ω AVOL Large Signal Voltage V S = ±15V, VO = ±10V 50 100 25 100 V/mV Gain R L = 10 kΩ ,TA = 25˚C Over Temperature 25 15 V/mV VO Output Voltage Swing V S = ±15V, RL = 10 kΩ ±12 ±13 ±12 ±13 V VCM Input Common-Mode ±16 +18 ±11 +14 V Voltage Range −17 −12 V CMRR Common-Mode R S ≤ 10 kΩ 80 100 70 95 dB Rejection Ratio PSRR Supply Voltage (Note 7) 80 100 70 90 dB Rejection Ratio IS Supply Current 0.6 0.8 0.6 1.0 mA www.national.com 2

Symbol Parameter Conditions LF444A LF444 Units Min Typ Max Min Typ Max Amplifier-to-Amplifier −120 −120 dB Coupling SR Slew Rate V S = ±15V, TA = 25˚C 1 1 V/µs GBW Gain-Bandwidth Product V S = ±15V, TA = 25˚C 1 1 MHz en Equivalent Input Noise Voltage TA = 25˚C, RS = 100Ω , 35 35 f= 1 kHz in Equivalent Input Noise Current TA = 25˚C, f= 1 kHz 0.01 0.01 Note 1:Unless otherwise specified the absolute maximum negative input voltage is equal to the negative power supply voltage. Note 2:Any of the amplifier outputs can be shorted to ground indefinitely, however, more than one should not be simultaneously shorted as the maximum junction temperature will be exceeded. Note 3:For operating at elevated temperature, these devices must be derated based on a thermal resistance ofθjA. Note 4:The LF444A is available in both the commercial temperature range 0˚C≤ TA ≤ 70˚C and the military temperature range −55˚C≤ TA ≤ 125˚C. The LF444 is available in the commercial temperature range only. The temperature range is designated by the position just before the package type in the device number. A “C” indicates the commercial temperature range and an “M” indicates the military temperature range. The military temperature range is available in “D” package only. Note 5:Unless otherwise specified the specifications apply over the full temperature range and for VS = ±20V for the LF444A and for VS = ±15V for the LF444. VOS , IB, and IOS are measured at VCM = 0. Note 6:The input bias currents are junction leakage currents which approximately double for every 10˚C increase in the junction temperature, Tj. Due to limited pro- duction test time, the input bias currents measured are correlated to junction temperature. In normal operation the junction temperature rises above the ambient tem- perature as a result of internal power dissipation, PD .Tj= TA + θjAPD where θjAis the thermal resistance from junction to ambient. Use of a heat sink is recommended if input bias current is to be kept to a minimum. Note 7:Supply voltage rejection ratio is measured for both supply magnitudes increasing or decreasing simultaneously in accordance with common practice from ±15V to±5V for the LF444 and from±20V to±5V for the LF444A. Note 8:Refer to RETS444X for LF444MD military specifications. Note 9:Max. Power Dissipation is defined by the package characteristics. Operating the part near the Max. Power Dissipation may cause the part to operate outside guaranteed limits. Note 10:Human body model, 1.5 kΩ in series with 100 pF. Note 11:Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which the device is func- tional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guar- antee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Typical Performance Characteristics Input Bias Current DS009156-12 Input Bias Current DS009156-13 Supply Current DS009156-14 www.national.com3

Typical Performance Characteristics(Continued) Positive Common-Mode Input Voltage Limit DS009156-15 Negative Common-Mode Input Voltage Limit DS009156-16 Positive Current Limit DS009156-17 Negative Current Limit DS009156-18 Output Voltage Swing DS009156-19 Output Voltage Swing DS009156-20 Gain Bandwidth DS009156-21 Bode Plot DS009156-22 Slew Rate DS009156-23 www.national.com 4

Typical Performance Characteristics(Continued) Distortion vs Frequency DS009156-24 Undistorted Output Voltage Swing DS009156-25 Open Loop Frequency Response DS009156-26 Common-Mode Rejection Ratio DS009156-27 Power Supply Rejection Ratio DS009156-28 Equivalent Input Noise Voltage DS009156-29 Open Loop Voltage Gain DS009156-30 Output Impedance DS009156-31 Inverter Settling Time DS009156-32 www.national.com5

Pulse Response R L = 10 kΩ ,C L = 10 pF Application Hints This device is a quad low power op amp with JFET input de- vices ( BI-FET™ ). These JFETs have large reverse break- down voltages from gate to source and drain eliminating the need for clamps across the inputs. Therefore, large differen- tial input voltages can easily be accommodated without a large increase in input current. The maximum differential in- put voltage is independent of the supply voltages. However, neither of the input voltages should be allowed to exceed the negative supply as this will cause large currents to flow which can result in a destroyed unit. Exceeding the negative common-mode limit on either input will force the output to a high state, potentially causing a re- versal of phase to the output. Exceeding the negative common-mode limit on both inputs will force the amplifier output to a high state. In neither case does a latch occur since raising the input back within the common-mode range again puts the input stage and thus the amplifier in a normal operating mode. Exceeding the positive common-mode limit on a single input will not change the phase of the output; however, if both in- puts exceed the limit, the output of the amplifier will be forced to a high state. The amplifiers will operate with a common-mode input volt- age equal to the positive supply; however, the gain band- width and slew rate may be decreased in this condition. When the negative common-mode voltage swings to within 3V of the negative supply, an increase in input offset voltage may occur. Each amplifier is individually biased to allow normal circuit operation with power supplies of ±3.0V. Supply voltages less than these may degrade the common-mode rejection and re- strict the output voltage swing. The amplifiers will drive a 10 kΩ load resistance to ±10V over the full temperature range. If the amplifier is forced to drive heavier load currents, however, an increase in input offset voltage may occur on the negative voltage swing and finally reach an active current limit on both positive and negative swings. Small Signal Inverting DS009156-6 Small Signal Non-Inverting DS009156-7 Large Signal Inverting DS009156-8 Large Signal Non-Inverting DS009156-9 www.national.com 6

Application Hints(Continued) Precautions should be taken to ensure that the power supply for the integrated circuit never becomes reversed in polarity or that the unit is not inadvertently installed backwards in a socket as an unlimited current surge through the resulting forward diode within the IC could cause fusing of the internal conductors and result in a destroyed unit. As with most amplifiers, care should be taken with lead dress, component placement and supply decoupling in order to ensure stability. For example, resistors from the output to an input should be placed with the body close to the input to minimize “pick-up” and maximize the frequency of the feed- back pole by minimizing the capacitance from the input to ground. A feedback pole is created when the feedback around any amplifier is resistive. The parallel resistance and capacitance from the input of the device (usually the inverting input) to AC ground set the frequency of the pole. In many instances the frequency of this pole is much greater than the expected 3 dB frequency of the closed loop gain and consequently there is negligible effect on stability margin. However, if the feed- back pole is less than approximately 6 times the expected 3 dB frequency a lead capacitor should be placed from the out- put to the input of the op amp. The value of the added ca- pacitor should be such that the RC time constant of this ca- pacitor and the resistance it parallels is greater than or equal to the original feedback pole time constant. Typical Application pH Probe Amplifier/Temperature Compensator DS009156-10 For R2 = 100k, R4= 75k ±1% For R2 = 200k, R4= 56k ±1% **Polystyrene *Film resistor type RN60C To calibrate, insert probe in pH=7 solution. Set the “TEMPERATURE ADJUST” pot, R2, to correspond to the solution temperature: full clockwise for 0˚C, and proportionately for intermediate temperatures, using a turns-counting dial. Then set “CALIBRATE” pot so output reads 7V. Typical probe= Ingold Electrodes#465-35 www.national.com7

www.national.com 8

Physical Dimensionsinches (millimeters) unless otherwise noted Order Number LF444AMD or LF444MD/883 See NS Package Number D14E Order Number LF444CM See NS Package Number M14A www.national.com9

Physical Dimensionsinches (millimeters) unless otherwise noted (Continued) LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Français Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 www.national.com Order Number LF444ACN or LF444CN See NS Package Number N14A LF444 Quad Low Power JFET Input Operational Amplifier National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.