LF351-N

LF351 TI1 | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 14

Technical content

LF351 Wide Bandwidth JFET Input Operational Amplifier Literature Number: SNOSBH2

Wide Bandwidth JFET Input Operational Amplifier General Description The LF351 is a low cost high speed JFET input operational amplifier with an internally trimmed input offset voltage (BI-FET II ™ technology). The device requires a low supply current and yet maintains a large gain bandwidth product and a fast slew rate. In addition, well matched high voltage JFET input devices provide very low input bias and offset currents. The LF351 is pin compatible with the standard LM741 and uses the same offset voltage adjustment cir- cuitry. This feature allows designers to immediately upgrade the overall performance of existing LM741 designs. The LF351 may be used in applications such as high speed integrators, fast D/A converters, sample-and-hold circuits and many other circuits requiring low input offset voltage, low input bias current, high input impedance, high slew rate and wide bandwidth. The device has low noise and offset voltage drift, but for applications where these requirements are critical, the LF356 is recommended. If maximum supply current is important, however, the LF351 is the better choice.

Features

n Internally trimmed offset voltage: 10 mV n Low input bias current: 50 pA n Low input noise voltage: n Low input noise current: n Wide gain bandwidth: 4 MHz n High slew rate: 13 V/µs n Low supply current: 1.8 mA n High input impedance: 1012Ω n Low total harmonic distortion AV =10,: <0.02% R L=10k, VO =20 Vp-p, BW=20 Hz–20 kHz n Low 1/f noise corner: 50 Hz n Fast settling time to 0.01% :2 µ s Typical Connection Simplified Schematic BI-FET II™ is a trademark of National Semiconductor Corporation. DS005648-11 DS005648-12 April 1998 LF351 Wide Bandwidth JFET Input Operational Amplifier LF351 © 1998 National Semiconductor Corporation DS005648 www.national.com 1 PrintDate=1998/04/07 PrintTime=13:52:34 38265 ds005648 Rev. No. 3 cmservProof 1

Order Number LF351M or LF351N See NS Package Number M08A or N08E PrintDate=1998/04/07 PrintTime=13:52:34 38265 ds005648 Rev. No. 3 cmservProof 2 www.national.com 2

Absolute Maximum Ratings(Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage ±18V Power Dissipation (Notes 2, 7) 670 mW Operating Temperature Range 0˚C to +70˚C T j(MAX) 115˚C Differential Input Voltage ±30V Input Voltage Range (Note 3) ±15V Output Short Circuit Duration Continuous Storage Temperature Range −65˚C to +150˚C Lead Temp. (Soldering, 10 sec.) Metal Can 300˚C DIP 260˚C θ jA N Package 120˚C/W M Package TBD Soldering Information Dual-In-Line Package Soldering (10 sec.) 260˚C Small Outline Package Vapor Phase (60 sec.) 215˚C Infrared (15 sec.) 220˚C See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” for other methods of soldering surface mount devices. ESD rating to be determined Symbol Parameter Conditions LF351 Units Min Typ Max VOS Input Offset Voltage R S = 10 kΩ ,TA = 25˚C 5 10 mV Over Temperature 13 mV ΔVOS /ΔT Average TC of Input Offset R S =10 kΩ 10 µV/˚C Voltage IOS Input Offset Current T j = 25˚C, (Notes 4, 5) 25 100 pA Tj≤ 70˚C 4 nA IB Input Bias Current T j = 25˚C, (Notes 4, 5) 50 200 pA Tj≤ ±70˚C 8 nA R IN Input Resistance T j=25˚C 10 12 Ω AVOL Large Signal Voltage Gain V S =±15V, TA =25˚C 25 100 V/mV VO =±10V, RL=2k Ω Over Temperature 15 V/mV VO Output Voltage Swing V S =±15V, RL=10 kΩ ±12 ±13.5 V VCM Input Common-Mode Voltage +15 V Range V S =±15V ±11 −12 V CMRR Common-Mode Rejection Ratio R S≤10 kΩ 70 100 dB PSRR Supply Voltage Rejection Ratio (Note 6) 70 100 dB I S Supply Current 1.8 3.4 mA Note 1:Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is func- tional, but do not guarantee specific performance limits. Note 2:For operating at elevated temperature, the device must be derated based on the thermal resistance,θJA. Note 3:Unless otherwise specified the absolute maximum negative input voltage is equal to the negative power supply voltage. Note 4:These specifications apply for VS =±15V and 0˚C≤TA≤+70˚C. VOS ,IB and IOS are measured at VCM =0. Note 5:The input bias currents are junction leakage currents which approximately double for every 10˚C increase in the junction temperature, Tj. Due to the limited production test time, the input bias currents measured are correlated to junction temperature. In normal operation the junction temperature rises above the ambient temperature as a result of internal power dissipation, P D .Tj=TA+θjA PD where θjA is the thermal resistance from junction to ambient. Use of a heat sink is recom- mended if input bias current is to be kept to a minimum. Note 6:Supply voltage rejection ratio is measured for both supply magnitudes increasing or decreasing simultaneously in accordance with common practice. From ±15V to±5V. Note 7:Max. Power Dissipation is defined by the package characteristics. Operating the part near the Max. Power Dissipation may cause the part to operate outside guaranteed limits. 3 www.national.com PrintDate=1998/04/07 PrintTime=13:52:34 38265 ds005648 Rev. No. 3 cmservProof 3

Symbol Parameter Conditions LF351 Units Min Typ Max SR Slew Rate V S =±15V, TA =25˚C 13 V/µs GBW Gain Bandwidth Product V S =±15V, TA =25˚C 4 MHz en Equivalent Input Noise Voltage T A = 25˚C, RS =100Ω ,2 5 f= 1000 Hz in Equivalent Input Noise Current T j = 25˚C, f=1000 Hz 0.01 Typical Performance Characteristics Input Bias Current DS005648-14 Input Bias Current DS005648-15 Supply Current DS005648-16 Positive Common-Mode Input Voltage Limit DS005648-17 Negative Common-Mode Input Voltage Limit DS005648-18 Positive Current Limit DS005648-19 Negative Current Limit DS005648-20 Voltage Swing DS005648-21 Output Voltage Swing DS005648-22 PrintDate=1998/04/07 PrintTime=13:52:34 38265 ds005648 Rev. No. 3 cmservProof 4 www.national.com 4

Typical Performance Characteristics(Continued) Gain Bandwidth DS005648-23 Bode Plot DS005648-24 Slew Rate DS005648-25 Distortion vs Frequency DS005648-26 Undistorted Output Voltage Swing DS005648-27 Open Loop Frequency Response DS005648-28 Common-Mode Rejection Ratio DS005648-29 Power Supply Rejection Ratio DS005648-30 Equivalent Input Noise Voltage DS005648-31 5 www.national.com PrintDate=1998/04/07 PrintTime=13:52:34 38265 ds005648 Rev. No. 3 cmservProof 5

Typical Performance Characteristics(Continued) Pulse Response Open Loop Voltage Gain (V/V) DS005648-32 Output Impedance DS005648-33 Inverter Settling Time DS005648-34 Small Signal Inverting DS005648-4 Small Signal Non-Inverting DS005648-5 Large Signal Inverting DS005648-6 Large Signal Non-Inverting DS005648-7 PrintDate=1998/04/07 PrintTime=13:52:35 38265 ds005648 Rev. No. 3 cmservProof 6 www.national.com 6

Pulse Response (Continued) Application Hints The LF351 is an op amp with an internally trimmed input off- set voltage and JFET input devices (BI-FET II™ ). These JFETs have large reverse breakdown voltages from gate to source and drain eliminating the need for clamps across the inputs. Therefore, large differential input voltages can easily be accommodated without a large increase in input current. The maximum differential input voltage is independent of the supply voltages. However, neither of the input voltages should be allowed to exceed the negative supply as this will cause large currents to flow which can result in a destroyed unit. Exceeding the negative common-mode limit on either input will force the output to a high state, potentially causing a re- versal of phase to the output. Exceeding the negative common-mode limit on both inputs will force the amplifier output to a high state. In neither case does a latch occur since raising the input back within the common-mode range again puts the input stage and thus the amplifier in a normal operating mode. Exceeding the positive common-mode limit on a single input will not change the phase of the output; however, if both in- puts exceed the limit, the output of the amplifier will be forced to a high state. The amplifier will operate with a common-mode input voltage equal to the positive supply; however, the gain bandwidth and slew rate may be decreased in this condition. When the negative common-mode voltage swings to within 3V of the negative supply, an increase in input offset voltage may oc- cur. The LF351 is biased by a zener reference which allows nor- mal circuit operation on ±4V power supplies. Supply volt- ages less than these may result in lower gain bandwidth and slew rate. The LF351 will drivea2k Ω load resistance to ±10V over the full temperature range of 0˚C to +70˚C. If the amplifier is forced to drive heavier load currents, however, an increase in input offset voltage may occur on the negative voltage swing and finally reach an active current limit on both posi- tive and negative swings. Precautions should be taken to ensure that the power supply for the integrated circuit never becomes reversed in polarity or that the unit is not inadvertently installed backwards in a socket as an unlimited current surge through the resulting forward diode within the IC could cause fusing of the internal conductors and result in a destroyed unit. As with most amplifiers, care should be taken with lead dress, component placement and supply decoupling in order to ensure stability. For example, resistors from the output to an input should be placed with the body close to the input to minimize “pick-up” and maximize the frequency of the feed- back pole by minimizing the capacitance from the input to ground. A feedback pole is created when the feedback around any amplifier is resistive. The parallel resistance and capacitance from the input of the device (usually the inverting input) to AC ground set the frequency of the pole. In many instances the frequency of this pole is much greater than the expected 3 dB frequency of the closed loop gain and consequently there is negligible effect on stability margin. However, if the feed- back pole is less than approximately 6 times the expected 3 dB frequency a lead capacitor should be placed from the out- put to the input of the op amp. The value of the added ca- pacitor should be such that the RC time constant of this ca- pacitor and the resistance it parallels is greater than or equal to the original feedback pole time constant. Current Limit (R L=100Ω ) DS005648-8 7 www.national.com PrintDate=1998/04/07 PrintTime=13:52:35 38265 ds005648 Rev. No. 3 cmservProof 7

Supply Current Indicator/Limiter DS005648-40

• VOUT switches high when RSIS > VD Hi-ZIN Inverting Amplifier DS005648-41 Parasitic input capacitance C1≅ (3 pF for LF351 plus any additional layout capacitance) interacts with feedback elements and creates undesirable high frequency pole. To compensate, add C2 such that: R2C2 ≅ R1C1. PrintDate=1998/04/07 PrintTime=13:52:35 38265 ds005648 Rev. No. 3 cmservProof 8 www.national.com 8

Typical Applications(Continued) Ultra-Low (or High) Duty Cycle Pulse Generator DS005648-42 where VS = V+ +| V−| *low leakage capacitor Long Time Integrator DS005648-43 *Low leakage capacitor

• 50k pot used for less sensitive VOS adjust 9 www.national.com PrintDate=1998/04/07 PrintTime=13:52:35 38265 ds005648 Rev. No. 3 cmservProof 9 Book Extract End

THIS PAGE IS IGNORED IN THE DATABOOK PrintDate=1998/04/07 PrintTime=13:52:35 38265 ds005648 Rev. No. 3 cmservProof 10

Physical Dimensionsinches (millimeters) unless otherwise noted Order Number LF351M Molded Dual-In-Line Package (N) Order Number LF351N 11 www.national.com 11 PrintDate=1998/04/07 PrintTime=13:52:35 38265 ds005648 Rev. No. 3 cmservProof 11

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DE- VICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMI- CONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or sys- tems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose fail- ure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component in any component of a life support device or system whose failure to perform can be rea- sonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Français Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5620-6175 Fax: 81-3-5620-6179 LF351 Wide Bandwidth JFET Input Operational Amplifier PrintDate=1998/04/07 PrintTime=13:52:35 38265 ds005648 Rev. No. 3 cmservProof 12 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.

Texas InstrumentsIncorporatedand itssubsidiaries(TI)reservetherighttomake corrections,modifications,enhancements,improvements, and otherchanges toitsproductsand servicesatany timeand todiscontinueany productorservicewithoutnotice.Customersshould obtainthelatestrelevantinformationbeforeplacingordersand shouldverifythatsuch informationiscurrentand complete.Allproductsare soldsubjecttoTI’s termsand conditionsofsalesuppliedatthetimeoforderacknowledgment. TIwarrantsperformanceofitshardwareproductstothespecificationsapplicableatthetimeofsaleinaccordancewithTI’s standard warranty.Testingand otherqualitycontroltechniquesareused totheextentTIdeems necessarytosupportthiswarranty.Exceptwhere mandated by governmentrequirements,testingofallparametersofeach productisnotnecessarilyperformed. TIassumes no liabilityforapplicationsassistanceorcustomerproductdesign.Customersareresponsiblefortheirproductsand applicationsusingTIcomponents.To minimizetherisksassociatedwithcustomerproductsand applications,customersshouldprovide adequatedesignand operatingsafeguards. TIdoes notwarrantorrepresentthatany license,eitherexpressorimplied,isgrantedunderany TIpatentright,copyright,mask work right, orotherTIintellectualpropertyrightrelatingtoany combination,machine,orprocessinwhichTIproductsorservicesareused.Information publishedby TIregardingthird-partyproductsorservicesdoes notconstitutea licensefromTItouse such productsorservicesora warrantyorendorsementthereof.Use ofsuch informationmay requirea licensefroma thirdpartyunderthepatentsorotherintellectual propertyofthethirdparty,ora licensefromTIunderthepatentsorotherintellectualpropertyofTI. ReproductionofTIinformationinTIdatabooks ordatasheetsispermissibleonlyifreproductioniswithoutalterationand isaccompanied by allassociatedwarranties,conditions,limitations,and notices.Reproductionofthisinformationwithalterationisan unfairand deceptive businesspractice.TIisnotresponsibleorliableforsuch altereddocumentation.Informationofthirdpartiesmay be subjecttoadditional restrictions. ResaleofTIproductsorserviceswithstatementsdifferentfromorbeyond theparametersstatedby TIforthatproductorservicevoidsall expressand any impliedwarrantiesfortheassociatedTIproductorserviceand isan unfairand deceptivebusinesspractice.TIisnot responsibleorliableforany such statements. TIproductsarenotauthorizedforuse insafety-criticalapplications(suchas lifesupport)where a failureoftheTIproductwouldreasonably be expectedtocause severepersonalinjuryordeath,unlessofficersofthepartieshave executedan agreementspecificallygoverning such use.Buyersrepresentthattheyhave allnecessaryexpertiseinthesafetyand regulatoryramificationsoftheirapplications,and acknowledgeand agreethattheyaresolelyresponsibleforalllegal,regulatoryand safety-relatedrequirementsconcerningtheirproducts and any use ofTIproductsinsuch safety-criticalapplications,notwithstandingany applications-relatedinformationorsupportthatmay be providedby TI.Further,Buyersmust fullyindemnifyTIand itsrepresentativesagainstany damages arisingoutoftheuse ofTIproductsin such safety-criticalapplications. TIproductsareneitherdesignednorintendedforuse inmilitary/aerospaceapplicationsorenvironmentsunlesstheTIproductsare specificallydesignatedby TIas military-gradeor"enhanced plastic." Onlyproductsdesignatedby TIas military-grademeet military specifications.Buyersacknowledgeand agreethatany such use ofTIproductswhichTIhas notdesignatedas military-gradeissolelyat theBuyer's risk,and thattheyaresolelyresponsibleforcompliancewithalllegaland regulatoryrequirementsinconnectionwithsuch use. TIproductsareneitherdesignednorintendedforuse inautomotiveapplicationsorenvironmentsunlessthespecificTIproductsare designatedby TIas compliantwithISO/TS 16949 requirements.Buyersacknowledgeand agreethat,iftheyuse any non-designated productsinautomotiveapplications,TIwillnotbe responsibleforany failuretomeet such requirements. FollowingareURLs where you can obtaininformationon otherTexas Instrumentsproductsand applicationsolutions: Products Applications Audio www.ti.com/audio Communicationsand Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP ® Products www.dlp.com Energyand Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocksand Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space,Avionicsand Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportationand Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Videoand Imaging www.ti.com/video RFID www.ti-rfid.com OMAP MobileProcessors www.ti.com/omap WirelessConnectivity www.ti.com/wirelessconnectivity TIE2E Community Home Page e2e.ti.com MailingAddress:Texas Instruments,PostOfficeBox 655303,Dallas,Texas 75265 Copyright© 2011,Texas InstrumentsIncorporated