LD1985G-XX-AF5-R

LD1985_V01 UTC | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 9

Technical content

UNISONIC TECHNOLOGIES CO., LTD LD1985 LINEAR INTEGRATED CIRCUIT www.unisonic.com.tw 1 of 9 Copyright © 2020 Unisonic Technologies Co., Ltd QW-R102-021.J VERY LOW DROP AND LOW NOISE VOLTAGE REGULATOR LOW ESR CAP. COMPATIBLE, WITH INHIBIT FUNCTION  DESCRIPTION The UTC LD1985 is a 150mA fixed output voltage regulator. The ultra low drop voltage and the low quiescent current make them particularly suitable for low noise, low power applications, and in battery powered systems. In sleep mode quiescent current is less than 1μA when INHIBIT pin is pulled low. Shutdown Logic Control Function is available on pin 3 (TTL compatible). This means that when the device is used as local regulator, it is possible to put a part of the board in standby, decreasing the total power consumption. An external capacitor, CBYP=10nF, connected between bypass pin and GND reduce the noise to 30μVrms. Typical application is in cellular phone, palmtop laptop computer, personal digital assistant (PDA), personal stereo, camcorder and camera.  FEATURES * Very Low Dropout Voltage (280mV at 150mA and 7mV at 1mA Load) * Very Low Quiescent Current * Output Current up to 150mA * Logic Controlled Electronic Shutdown * Internal Current and Thermal Limit * Low Output Noise Voltage 30μVrms SOT-25  ORDERING INFORMATION Ordering Number Package Packing Lead Free Halogen Free LD1985L-xx-AF5-R LD1985G-xx-AF5-R SOT-25 Tape Reel Note: xx: Output Voltage, refer to Marking Information. (1) R: Tape Reel (2) AF5: SOT-25 (3) xx: Refer to Marking Information (4) G: Halogen Free and Lead Free, L: Lead Free LD1985G-xx-AF5-R (1)Packing Type (2)Package Type (3)Output Voltage Code (4)Green Package

LD1985 LINEAR INTEGRATED CIRCUIT UNISONIC TECHNOLOGIES CO., LTD 2 of 9 www.unisonic.com.tw QW-R102-021.J  MARKING INFORMATION PACKAGE VOLTAGE CODE MARKING SOT-25 15:1.5V 18:1.8V 25:2.5V 28:2.8V 2J:2.85V 30:3.0V 31:3.1V 32:3.2V 33:3.3V 35:3. 5V 36:3. 6V 38:3. 8V 40:4.0V 47:4. 7V 50:5.0V 321 LDXX 5 4 Voltage Code L: Lead Free G: Halogen Free  PIN CONFIGURATION 321 INHGNDVIN VOUT Byp  PIN DESCRIPTION PIN NO. PIN NAME DESCRIPTION

1 VIN Input port

2 GND Ground Pin

3 INHIBIT Control switches ON/OFF. Inhibit is not internally pulled -up; it cannot be left floating. Disable the device when connected to GND or to a positive voltage less than 0.18V

4 Bypass Bypass pin: capacitor to be connected to GND in order to improve the thermal noise

performances.

5 VOUT Output port

 BLOCK DIAGRAM VOUT DRIVERERROR AMPLIFIER CURRENT LIMIT REFERENCE VOLTAGE START-UP SHUTDOWN TERM. PROTEC. GND BYPASS INHIBIT VIN

LD1985 LINEAR INTEGRATED CIRCUIT UNISONIC TECHNOLOGIES CO., LTD 3 of 9 www.unisonic.com.tw QW-R102-021.J  ABSOLUTE MAXIMUM RATINGS (TA=25°C) PARAMETER SYMBOL RATINGS UNIT DC Input Voltage VIN 7 V INHIBIT Input Voltage VINH 7 V Output Current IOUT Internally limited Power Dissipation PD Internally limited Operating Junction Temperature TOPR -40 ~ +125 °C Storage Temperature TSTG -40 ~ +150 °C Note: Absolute maximum rating s are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied.  THERMAL DATA PARAMETER SYMBOL RATINGS UNIT Junction to Case θJC 81 °C/W  ELECTRICAL CHARACTRISTICS (TJ=25°C, VIN=VOUT+1V, IOUT=1mA, VSHDN=2V, CI=1μF, CO=1μF, unless otherwise specified) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Operating Input Voltage VI(OPR) 2.5 7 V Output Voltage VOUT VIN=2.5V 1.470 1.5 1.530 V IOUT=1 ~ 150mA 1.455 1.545 V VIN =2.8V 1.764 1.8 1.836 V IOUT =1 ~ 150mA 1.746 1.854 V VIN =3.5V 2.450 2.5 2.550 V IOUT =1 ~ 150mA 2.425 2.575 V VIN =3.8V 2.744 2.8 2.856 V IOUT =1 ~ 150mA 2.716 2.884 V VIN =3.85V 2.793 2.85 2.907 V IOUT =1 ~ 150mA 2.764 2.936 V VIN =4.0V 2.940 3.0 3.060 V IOUT =1 ~ 150mA 2.910 3.090 V VIN =4.1V 3.038 3.1 3.162 V IOUT =1 ~ 150mA 3.007 3.193 V VIN =4.2V 3.136 3.2 3.264 V IOUT =1 ~ 150mA 3.104 3.296 V VIN =4.3V 3.234 3.3 3.366 V IOUT =1 ~ 150mA 3.201 3.399 V VIN =4.5V 3.430 3.5 3.570 V IOUT =1 ~ 150mA 3.395 3.605 V VIN =4.6V 3.528 3.6 3.672 V IOUT =1 ~ 150mA 3.492 3.708 V VIN =4.8V 3.724 3.8 3.876 V IOUT =1 ~ 150mA 3.686 3.914 V VIN =5.0V 3.920 4 4.080 V IOUT =1 ~ 150mA 3.880 4.120 V VIN =5.7V 4.606 4.7 4.794 V IOUT =1 ~ 150mA 4.559 4.841 V VIN =6.0V 4.900 5 5.100 V IOUT =1 ~ 150mA 4.850 5.150 V

LD1985 LINEAR INTEGRATED CIRCUIT UNISONIC TECHNOLOGIES CO., LTD 4 of 9 www.unisonic.com.tw QW-R102-021.J  ELECTRICAL CHARACTRISTICS(Cont.) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Short Circuit Current ISC RL=0 600 mA Line Regulation △ VOUT VIN = VOUT +1V ~ 7V, IOUT =1mA 30 mV Dropout Voltage VD IOUT =0 1 3 mV IOUT =1mA 7 10 mV IOUT =10mA 40 60 mV IOUT =50mA 120 150 mV IOUT =150mA 280 350 mV Quiescent Current IQ IOUT =0 80 100 µA IOUT =1mA 100 150 µA IOUT =10mA 280 330 µA IOUT =50mA 1050 1300 µA IOUT =150mA 2900 3300 µA OFF MODE VINH<0.18V 1.5 µA Supply Voltage Rejection SVR CBYP=0.01μF, Co=10μF, f=1KHz 45 dB Control Input Logic Low VIL TJ=-20 ~ 125°C 0.15 V Control Input Logic High VIH TJ=-20 ~ 125°C 2 V Control Input Current IINH TJ=-20 ~ 125°C, VSHDN=5V 5 15 µA TJ=-20 ~ 125°C, VSHDN=0V 0 -1 µA Output Noise Voltage eN B=300Hz ~ 50KHz CBYP=0.01μF, Co=10μF 30 µV

LD1985 LINEAR INTEGRATED CIRCUIT UNISONIC TECHNOLOGIES CO., LTD 5 of 9 www.unisonic.com.tw QW-R102-021.J  REVERSE CURRENT TEST CIRCUIT VREV Bypass VIN 1µF VIN INH VINH1 GND VOUT 4.7µF A VIN

LD1985 LINEAR INTEGRATED CIRCUIT UNISONIC TECHNOLOGIES CO., LTD 6 of 9 www.unisonic.com.tw QW-R102-021.J  APPLICATION INFORMATION EXTERNAL CAPACITORS Like any low -dropout regulator, the UTC LD1985 requires external capacitors for regulator stability. This capacitor must be selected to meet the requirements of minimu m capacitance and equivalent series resistance. We suggest soldering input and outputting capacitors as close as possible to the relative pins. INPUT CAPACITOR An input capacitor whose value is 1 μF is required with the UTC LD1985 (amount of capacitance can be increased without limit). This capacitor must be located a distance of not more than 0.5" from the input pin of the device and returned to a clean analog ground. Any good quality ceramic, tan talum or film capacitors can be used for this capacitor. OUTPUT CAPACITOR The UTC LD1985 is designed specifically to work with ceramic output capacitors. It may also be possible to use Tantalum capacitors, but these are not as attractive for reasons of siz e and cost. By the way, the output capacitor must meet both the requirement for minimum amount of capacitance and E.S.R. (equivalent series resistance) value. Due to the different loop gain, the stability improves for higher output versions and so the suggested minimum output VOUT going from 1.8 ~ 3.3V, and 3.3 μF for the other versions. However, if an output capacitor lower than the suggested one is used, it's possible to make stable the regulator adding a resistor in series to the capacitor. IMPORTANT: The output capacitor must maintain its ESR in the stable region over the full operating temperature to assure stability. Also, capacitor tolerance and variation with temperature must be considered to assure the minimum amount of capacitance is provided at all times. This capacitor should be located not more than 0.5" from the output pin of the device and returned to a clean analog ground. INHIBIT INPUT OPERATION The inhibit pin can be used to turn OFF the regulator when pulled low, so drastically reducing the current consumption down to less than 1 μA. When the inhibit feature is not used, this pin must be tied to V IN to keep the regulator output ON at all times. To assure proper operation, the signal source used to drive the inhibit pin must be able to swing above and below the specified thresholds listed in the electrical characteristics section under V IH VIL. Any slew rate can be used to drive the inhibit. REVERSE CURRENT The power transistor used in the UTC LD1985 has not an inherent diode connected between the regulator input and output. If the output is forced above the input, no current will flow from the output to the input across the series pass transistor. When a V REV voltage is applied on the output, the reverse current measured flows to the GND across the two feedback resistors. This current typical value is 160 μA. R1 and R2 resistors are implanted type; typical values are, respectively, 42.6 KΩ and 51.150 KΩ.

LD1985 LINEAR INTEGRATED CIRCUIT UNISONIC TECHNOLOGIES CO., LTD 7 of 9 www.unisonic.com.tw QW-R102-021.J  TYPICAL CHARACTERISTICS (TJ=25°C, CIN=1μF, COUT=2.2μF, CBYP=100nF) 2.58 -25-50 250 2.46 2.50 2.56 2.54 2.48 2.44 50 100 Output Voltage vs Temperature 2.52 Tc (℃ ) 2.42 2.40 VOUT (V) VIN=3.5V IOUT=1mA 2500 250 7550 500 2000 125 1500 100 150 Quiescent Current vs Load Current 1000 IOUT (mA) IQ (μA) VOUT=2.5V CBY=10nF 125 2.60 175 -25-50 250 0.2 0.3 0.1 50 100 Dropout Voltage vs Temperature VD (V) VOUT=2.5V CBY=10nF IOUT=150mA IOUT=50mA IOUT=10mA IOUT=1mA -25-50 250 2.0 3.5 1.5 50 100 Quiescent Current vs Temperature IQ (mA) VOUT=2.5V CBY=10nF IOUT=150mA 3.0 2.5 1.0 0.5 TC (℃ ) TC (℃ ) 125 250 7550 100 150 250 125 200 100 150 Dropout Voltage vs Output Current IOUT (mA) VD (mV) VOUT=2.5V -25-50 250 50 100 Supply Voltage Rejection vs Temperature SVR (dB) COUT=10μF80 COUT=1μF fOSC=1KHz VIN=3.5 ~ 6.5V IOUT=10mA TC (℃ ) 125175 0.4 125 3000

LD1985 LINEAR INTEGRATED CIRCUIT UNISONIC TECHNOLOGIES CO., LTD 8 of 9 www.unisonic.com.tw QW-R102-021.J  TYPICAL CHARACTERISTICS (Cont.) 250 7550 125 100 150 Supply Voltage Rejection vs Output Current IOUT (mA) SVR (dB) VIN=3.5 ~ 6.5V COUT=10μF fOSC=1KHz Supply Voltage Rejection vs Frequency f (KHz) SVR (dB) 50 101 102 103 104 VIN=3.5 ~ 6.5V IOUT=10mA VOUT=2.5V COUT=1μF 250 7550 125 100 150 Supply Voltage Rejection vs Output Current IOUT (mA) VIN=3.5 ~ 6.5V COUT=1μF fOSC=1KHz Line Transient VIN VOUT VOUT=2.5V, IOUT=50mA, no CIN, COUT=4.7μF, tR=tF=20ns Ch1 500mV 20.0mVCH2 M 10.0μs Ch1 3.96VCh2 100 175 SVR (dB) 100 175 105 Line Transient VIN VOUT VOUT=2.5V, IOUT=50mA, no CIN, COUT=4.7μF, tR=tF=1μs 500mV 20.0mVCH2 M 10.0μs Ch1 3.96V Ch1 Ch2 f (KHz) Supply Voltage Rejection vs Frequency SVR (dB) 101 102 103 104 VIN=2.8 ~ 5.8V IOUT=10mA VOUT=1.8V COUT=10μF 105 Tek Run:5.00MS/s Tek Run:5.00MS/s

LD1985 LINEAR INTEGRATED CIRCUIT UNISONIC TECHNOLOGIES CO., LTD 9 of 9 www.unisonic.com.tw QW-R102-021.J  TYPICAL CHARACTERISTICS (Cont.) Load Transient VOUT VOUT=2.5V, IOUT=0~50mA, no CIN, COUT=10μF, tS=tF=2ns 20.0mV 50.0mVΩ Ch2 29mVCh3 Ch2 M 10.0μs Load Transient IOUT VOUT VOUT=2.5V, IOUT=50mA, no CIN, COUT=4.7μF, tS=tF=20ns Ch1 50.0mV 100mVΩCH2 M 10.0μs Ch2 78mVCh2 Tek Run: 5.00MS/s Tek Run: 5.00MS/s UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury . Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner . UTC reserves the right to make changes to information published in this document , including without limitation specifications and product descriptions , at any time and without notice . This document supersedes and replaces all information supplied prior to the publication hereof.