LD154TG LIGHTGRAPHIX | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 7
Technical content
Page 1 of 7 | Data sheet issued: 18 June KEY FEATURES DIMENSIONS > Features an asymmetric beam with optics set at a 3° tilt, helping to reduce glare and focus the light where needed > High-power P1 engine with CREE COB delivering upto 1375lm at 500mA in 3000K > E3 engine with NICHIA LED delivering up to 631lm at 700mA in 3000K offering an exceptional 10° extra narrow beam with peak intensity reaching 13,539cd > N1 engine with CREE COB delivering up to 851lm at 700mA in 3000K offering a 14° narrow beam > Durable all glass bezel, suitable for a wide range of applications > Utilises large 50mm low glare optics, chosen for efficiency, quality of beam and ability to produce narrow beams at high outputs > Low glare product with a choice of accessories to minimise the view of the light source at various angles > Fixing options include rebated trimless fixing sleeve, concrete housing and trimless ground tube > Contains our integral moisture guard (anti-wicking barrier), stopping water ingress from going up the cable into the product from incorrect IP-rated connections > Switched, 0-10V, Casambi, DMX, DALI, or Mains dimmable drivers available Dimensions in mm For fixings and dimensions please go to page 3. Ø90 TRIMLESS HIGH-POWER TITLED RECESSED EXTERIOR LED UPLIGHT The LD154TG is part of our Ultra range, delivering up to 1375lm from a minimal body depth of 85mm including the seamless glass bezel. It features an asymmetric beam with optics set at a 3° tilt, allowing the fitting to be installed further away from the lit surface and focus the light where needed. There are 3 LED engine options available. Our new P1 engine delivers the highest output, whilst the E3 offers an exceptional extra narrow beam of 9°, and the N1, a narrow 13° beam. The lens assembly features large 50mm optics which offer ultra-high efficiency, superior beam quality and low glare. Reaching heights of up to 14 metres and designed with our robust glass bezel, the LD154TG demonstrates an excellent size-to-output ratio, offering a discreet yet powerful exterior solution. LD154TG
Page 2 of 7 | Data sheet issued: 18 June WHITE LED ENGINE SPECIFICATION ENVIRONMENTAL TM65 Available on request TM66 2.5 Repair + Refurbish This product is included in our Repair and Refurbish scheme. This offers customers the ability to send back products to us for repair or refurbishment to extend their life without having to buy new fittings. Engine E3 N1 P1 LED manufacturer NICHIA CREE CREE Colour temperature 2200K, 2700K, 3000K, 4000K, 5000K 2200K, 2700K, 3000K, 4000K, 5000K 2200K, 2700K, 3000K, 4000K, 5000K Current [Rated Output] 350mA[5W] 500mA[7W] 700mA[10W] 350mA[7W] 500mA[10W] 700mA[14W] 350mA[14W] 500mA[20W] Delivered lumens (L 100)* 362 490 631 463 634 851 963 1375 Delivered lm/Circuit W 82 76 68 72 68 64 72 70 Source LED lm 574 740 949 694 937 1264 1449 1983 Source lm/W 144 128 114 120 112 105 121 113 CRI 85 90* 93 90 Colour consistency 2 SDCM 2 SDCM 3 SDCM Peak intensity 13,539 cd 10,837 cd 10,060 cd LOR 0.66 0.67 0.69 TM30 RF86 | RG98 RF91 | RF98 RF91 | RG98 BUG rating (‘uplight’ mounted) B0-U3-G0 B0-U4-G0 B0-U4-G0 B0-U5-G0 B0-U5-G1 LED lifetime L90B5 at 90,000hrs
Applications
These values are based on LD154TG-E3-700/830/ENB, LD154TG-N1-700/930/NB and LD154TG-P1-700/930/NB *See lumen variance table to the right for N1 engine. E3 lumens apply across all colour temperatures LED wattage includes losses assocaited with using a 90% efficient driver *90 CRI available in 2700K/3000K only. Approx. 10% lumen drop will occur compared to 85 CRI variants Lumen variance by CCT 2200K -7% 2700K +/- 0% 4000K +7% 5000K +16% MECHANICAL 350mA 500mA 700mA Ambient temperature 55°C Soil/Sleeve -20°C to 55°C -20°C to 55°C -20°C to 40°C Concrete -20°C to 55°C -20°C to 55°C -20°C to 50°C Soil/Sleeve -20°C to 55°C -20°C to 50°C -20°C to 25°C Concrete -20°C to 55°C -20°C to 55°C -20°C to 50°C Soil/Sleeve -20°C to 25°C N/A - Concrete -20°C to 45°C -20°C to 25°C - Glass 6mm thick toughened glass with black ceramic screen print Materials Black anodised aluminium body with black anodised bezel and glass front Weight of product 0.52kg IP rating IP67 IK rating IK08 Wiring In-series constant current wiring (pre-wired with 2 core cable at a length of 250mm)
Page 3 of 7 | Data sheet issued: 18 June DIMENSIONS AND FIXING OPTIONS Dimensions in mm /485NG or /485NG-2 Trimless concrete housing The aluminium housing is used as a heat sink which keeps the LED fitting cool through the thermal transfer of the heat within the housing to the surrounding concrete. The housings are big enough for IP rated connections to be made inside the housing and a second gland is available for cabling onto the next luminaire. The housing can be buried with the necessary wiring, and then the fitting installed after the landscaping work has been completed. Weight: 2.90kg. Fixing ring available with a passivated stainless steel or powder coat black finish.* /485NG Trimless concrete housing with 1x PG9 IP67 gland /485NG-2 Trimless concrete housing with 2x PG9 IP67 gland Ø170 107 Ø90Ø90 107 Ø170 /485SG Rebated trimless fixing sleeve The sleeve is bonded into the mounting surface first and the fitting is held in with an O-ring. We recommend this method for mounting in exterior in-ground applications. Mounting surface will require an 16mm rebate to allow for flush installation. Fixing ring available with a passivated stainless steel or powder coat black finish.* /485GTG Trimless Ground tube fixing Designed for soil or gravel surfaces. It is supplied with the fixing sleeve bonded into the tube and can be cut down on site. The tube can be buried with the necessary wiring via the PG9 IP67 gland and then the fitting installed after the landscaping work has been completed. Fixing ring available with a passivated stainless steel or powder coat black finish.* Ø90 135 Ø90 135 Ø80 Cut-out Ø86 15.8 Rebate Depth Ø91 Ø91 Ø80 Cut-out Ø86 71 85 Rebate depth
Page 4 of 7 | Data sheet issued: 18 June /HT-154-G Trimless Family Hand tool Our Trimless family fittings use a hand tool for easy intallation and removal that can be ordered separately. Use the /HT-154-G suction cup or a similar suction tool for the removal of the fittings from their fixing options. Please contact your LightGraphix sales representative for more information. How to use the hand tool Once secured, pull the fitting from its fixing accessory. Apply force vertically to ensure the suction cup does not detach. When adjusting or rotating the fitting do not use the HT-154-G hand tool to move in situ. Remove the fitting entirely, realign and then place the fitting back into its fixing option. Note: Rotating the fitting while still in place may result in a comprimised IP seal. 1 2 Place suction cup over the glass surface and lock in place by pulling the leaver into a vertical postion.
Page 5 of 7 | Data sheet issued: 18 June 3˚ TILT Both the LED and the optic are set at a 3° tilt, allowing for more efficient use of a glare shield, as more of the light output is directed towards the open aperture of the fitting. Should there be any obstructions preventing installation, then the tilt also allows the luminaire to be placed further away from the lit surface, without comprismising on output. GLARE CONTROL OPTIONS /GSHM154 Half-moon glare shield For applications that require low glare. Lumen output is typically reduced by 60% with no light lost on the lit surface. /NGS No glare shield No glare shield. Low glare optic and matt black anodised optic holder aids in glare reduction. /GSOB154 Oval beam glare shield Reduces the angles at which glare is visible without compromising the oval output of the beam. Useful when used in applications where glare can be seen from two sides, for example archways. /HL Honeycomb louvre Helps reduce glare from all angles and can be used with glare shields.
Page 6 of 7 | Data sheet issued: 18 June INSTALLATION GUIDE Below is an uplighting application guide with suggested luminaire mounting positions for an even wall wash. Every project and lighting scenario will be different and the table below is to be used as a starting point. Please use our photometric files to further test the desired effect for your application. Files are available on the LD154T product page on our website. B B A C LD154TG-E3 /ENB* /NB* /MSB /MB /WB /WWB /OB A Distance from the centre of the fitting to the lit surface B Spacing for an C 500mA lit distance 10M 7M 6.5M 5.5M 4.5M 4M 6M C 700mA lit distance 11M 8M 7M 6M 5M 4.5M 7M LD154TG-N1 /NB* /MSB /MB /WB /WWB /OB A Distance from the centre of the fitting to the lit surface B Spacing for an C 500mA lit distance 10M 8M 6.5M 5.5M 5M 7M C 700mA lit distance 11.5M 9M 7.5M 6.5M 6M 7.5M LD154TG-P1 /NB* /MSB /MB /WB /WWB /OB A Distance from the centre of the fitting to the lit surface B Spacing for an C 350mA lit distance 11M 9M 9M 7.5M 6M 8M C 500mA lit distance 14M 11M 10.5M 9M 8M 9M *Wall washing using narrow beam optics should only be used if the designer requires long distance lighting up the lit surface. **Illuminated distance is calculated based on achieving 10% of the initial lux calculated at the start of the beam.
Page 7 of 7 | Data sheet issued: 18 June ORDER CODES & OPTIONSORDER CODES & OPTIONS - LD154TG Example: LD154TG-E3-500/830/NB/GSHM154/485SG/Paint finish black Drivers Use with 350mA, 500mA & 700mA constant current LED drivers We have a range of dimmable LED drivers DMX and DALI compatible. Please see the downloads section on our website. Passivated Stainless Steel Paint finish Black (Powder Coat) / / / / / Light engine & drive current LD154TG - LED Colour Beam Angle Accessory Finish Fixing /NGS /GSHM154 /GSOB154 /HL /485SG /485GTG /485NG /485NG-2 10° Extra Narrow /ENB 11° Narrow /NB 22° Medium Spot /MSB 29° Medium /MB 42° Wide /WB 53° Extra Wide /WWB 10° x 56° Oval /OB 5W LED at 350mA LD154TG-E3-350 7W LED at 500mA* LD154TG-E3-500 10W LED at 700mA** LD154TG-E3-700 14W LED at 350mA LD154TG-P1-350 20W LED at 500mA LD154TG-P1-500 20° Narrow /NB 28° Medium Spot /MSB 34° Medium /MB 48° Wide /WB 63° Extra Wide /WWB 20° x 46° Oval /OB Ambient temperature key: 55°C 7W LED at 350mA LD154TG-N1-350 10W LED at 500mA* LD154TG-N1-500 14W LED at 700mA** LD154TG-N1-700 14° Narrow /NB 25° Medium Spot /MSB 31° Medium /MB 45° Wide /WB 62° Extra Wide /WWB 14° x 46° Oval /OB 2200K 85+ CRI /822 2700K 85+ CRI /827 3000K 85+ CRI /830 4000K 85+ CRI on request /840 5000K 85+ CRI /850 2700K 90+ CRI /927 3000K 90+ CRI /930 2200K 90+ CRI /922 2700K 90+ CRI /927 3000K 90+ CRI /930 4000K 90+ CRI on request /940 5000K 90+ CRI /950 2200K 93+ CRI /922 2700K 93+ CRI /927 3000K 93+ CRI /930 4000K 93+ CRI on request /940 5000K 93+ CRI /950 *55°C ambient when placed in a 485N / 485N-2 concrete can in concrete. **50°C ambient when placed in a 485N / 485N-2 concrete can in concrete. *55°C ambient when placed in a 485N / 485N-2 concrete can in concrete. **50°C ambient when placed in a 485N / 485N-2 concrete can in concrete.