LCV01-6 MICROSEMI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

Bidirectional TVS Array ™ LCV01-6 Microsemi Scottsdale Division 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503 Page 1Copyright  2003 5-30 2003 REV A WWW.Microsemi .COM SCOTTSDALE DIVISION LCV01-6 DESCRIPTION TVSARRAY™ This 16 pin one-line pair, bi-directional, LOW CAPACITANCE array is designed for use in applications where protection is required at the board level. It provides protection from voltage transients caused by electrostatic discharge (ESD) as defined in IEC 61000-4-2, electrical fast transients (EFT) per IEC 61000-4-4 and effects of secondary lightning as stated by IEC 61000-4-5. These TRANSIENT VOLTAGE SUPPRESSOR (TVS) arrays have a peak pulse power rating of 1500 watts for a 10/1000 µsec pulse and are designed to be used for secondary surge protection on high -speed telecommunications lines. This device can be used in either common or differential mode applications. It is typically used between Tip and Ring. Applications include T1/E1 and DSL interfaces in base stations, routers, and long -haul transient immunity requirement per Bellcore 1089, FCC Part 68 (type A and B surges and IEC 61000-4-5 IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com FEATURES APPLICATIONS / BENEFITS

  • 1500 watts peak pulse power
  • Protects one-line pair
  • Provides electrically isolated protection
  • SO-16W package
  • UL 94V-0 flamability classification
  • LOW CAPACITANCE 90 pF per line pair
  • T1/E1 line cards
  • Base stations
  • WAN interfaces
  • XDSL interfaces
  • CSU/DSU equipment MAXIMUM RATINGS MECHANICAL AND PACKAGING
  • Operating temperature: -55°C to +150°C
  • Storage temperature: -55°C to +150°C
  • Peak pulse power: 1500 watts (10/1000 µs, Fig 1)
  • Pulse repetition rate: < .01%
  • Thermal resistance:< 30°C/watt (junction-to-case)
  • Lead soldering temperature: 260°C, 10s maximum
  • Molded SO-16W Surface Mount
  • Weight 0.25 grams (approximate)
  • Marking: Logo, device marking code, date code
  • Pin #1 defined by dot on top of package
  • Tape & Reel per EIA Standard 481
  • 13 inch reel; 2,500 pieces (OPTIONAL)
  • Carrier tubes; 45 pcs (STANDARD) ELECTRICAL CHARACTERISTICS PER LINE PAIR @ 25°C Unless otherwise specified STAND OFF VOLTAGE VWM VOLTS BREAKDOWN VOLTAGE VBR @1 mA VOLTS CLAMPING VOLTAGE VC @ 100 Amp (Figure 2) VOLTS CLAMPING VOLTAGE VC @ 200 Amp (Figure 3) VOLTS STANDBY CURRENT ID @ VWM µA CAPACITANCE (f=1 MHz) C @0V pF PART NUMBER DEVICE MARKING MAX MIN MAX MAX MAX TYP LCV01-6 LCV01-6 6.0 8.0 15 21 25 90 Note: Transient Voltage Suppressor (TVS) product is normally selected based on its stand off voltage VWM. Product selected voltage should be equal to or greater than the continuous peak operating voltage of the circuit to be protected.

Bidirectional TVS Array ™ LCV01-6 Microsemi Scottsdale Division 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503 Page 2Copyright  2003 5-30 2003 REV A WWW.Microsemi .COM SCOTTSDALE DIVISION LCV01-6 SYMBOLS & DEFINITIONS Symbol Definition VWM Stand Off Voltage: Maximum dc voltage that can be applied over the operating temperature range. Vwm must be selected to be equal or be greater than the operating voltage of the line to be protected VBR Minimum Breakdown Voltage: The minimum voltage the device will exhibit at a specified current VC Clamping Voltage: Maximum clamping voltage across the TVS device when subjected to a given current at a pulse time, td. ID Standby Current: Leakage current at VWM. C Capacitance: Capacitance of the TVS as defined @ 0 volts at a frequency of 1 MHz and stated in picofarads. OUTLINE AND CIRCUIT Figure 1 Figure 2 Figure 3 Peak Pulse Power Vs Pulse Time t = sec Pulse Wave Form Pulse Wave Form DIMENSIONS AND SCHEMATIC B P G D C K J L F A INCHES MILLIMETERS MAX MIN DIM MAX MIN 0.413 A 0.397 10.08 10.49 0.299 0.291 7.39 7.60 0.104 0.081 2.06 2.64 0.020 0.013 0.33 0.51 0.050 0.016 0.41 1.27 0.050 BSC 1.27 BSC 0.012 0.009 0.23 0.30 0.004 0.001 0.03 0.10 0.387 0.344 7.47 9.79 B C D F G J K L 0.419 P 0.394 10.01 10.64 SCHEMATIC Ppp Peak Pulse Power (kW) .08/.10 2.1/2.6 .02/.03 .60/.80 .45/.48_ 11.6/11.8 .05 (nom) 1.27 (nom) .25/.27 6.6/6.8 PAD LAYOUT Half - Value -- Ipp 2 0 500 1000 1500 0 100 t -- Time in microseconds Ipp -- Peak Pulse Current -- % Ipp 10/1000 Waveform t t d Peak Value -- Ipp r Half - Value -- Ipp 2 0 100 200 300 0 100 t -- Time in microseconds Ipp -- Peak Pulse Current -- % Ipp 10/160 Waveform t t d Peak Value -- Ipp r 100ns 1µs 10µs 1ms 10ms 100ms 100 1.0 .10 10/1000µs 1500W Pulse