DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 29

Technical content

Features

Flash ROM

  • 8192 × 8 bits
  • Capable of On-board programming with wide range (2.2 to 5.5V) of voltage source.
  • Block-erasable in 128 byte units
  • Writable in 2-byte units RAM
  • 256 × 9 bits Package Form
  • MFP24SJ (300mil): Lead-/Halogen-free type
  • SSOP24 (225mil): Lead-free type
  • VCT24 (3.5×3.5): Lead-/Halogen-free type (build-to-order)
  • MFP24S (300mil): Lead-free type (discontinued) SANYO : MFP24SJ(300mil) 13.0 0.45 8.0 6.0 0.151.0 0.4(1.0)

1.9 MAX

0.1 (1.5) Package Dimensions unit : mm (typ) 3419 CMOS IC 8K-byte FROM and 256-byte RAM integrated 8-bit 1-chip Microcontroller * This product is licensed from Silicon Storage Technology, Inc. (USA).

No.A1028-2/29 Minimum Bus Cycle

  • 83.3ns (12MHz at VDD=2.7V to 5.5V)
  • 100ns (10MHz at VDD=2.2V to 5.5V)
  • 250ns (4MHz at VDD=1.8V to 5.5V) Note: The bus cycle time here refers to the ROM read speed. Minimum Instruction Cycle Time
  • 250ns (12MHz at VDD=2.7V to 5.5V)
  • 300ns (10MHz at VDD=2.2V to 5.5V)
  • 750ns (4MHz at VDD=1.8V to 5.5V) Package Dimensions unit : mm (typ) 3287 SANYO : SSOP24(225mil) 6.4 6.5 0.5 4.4 (0.5) (1.3) 24 13 1 12 0.22 0.5 0.15 0.1 1.5max SANYO : VCT24(3.5X3.5) 3.5 3.5 0.4 0.8 (0.035) 0.5 (0.5) TOP VIEW SIDE VIEW SIDE VIEW BOTTOM VIEW (0.125) (C0.17) (0.13) 0.25 Package Dimensions unit : mm (typ) 3322A (Build-to-order) Package Dimensions unit : mm (typ) 3112B (Discontinued) SANYO : MFP24S(300mil) 1 12 1324 12.5 0.63 7.6 5.4 0.151.0 0.35 (0.75) 1.7max 0.1 (1.5)

No.A1028-3/29 Ports

  • Normal withstand voltage I/O ports Ports I/O direction can be designated in 1-bit units 11 (P1n, P20, P21, P70) Ports I/O direction can be designated in 4-bit units 8 (P0n)
  • Dedicated oscillator ports/input ports 2 (CF1/XT1, CF2/XT2)
  • Reset pin 1 ( RES)
  • Power pins 2 (V SS1, VDD1) Timers
  • Timer 0: 16-bit timer/counter with a capture register. Mode 0: 8-bit timer with an 8-bit programmable prescaler (with an 8-bit capture register) × 2 channels Mode 1: 8-bit timer with an 8-bit programmable prescaler (with an 8-bit capture register) + 8-bit counter (with an 8-bit capture register) Mode 2: 16-bit timer with an 8-bit programmable prescaler (with a 16-bit capture register) Mode 3: 16-bit counter (with a 16-bit capture register)
  • Timer 1: 16-bit timer/counter that supports PWM/toggle outputs Mode 0: 8-bit timer with an 8-bit prescaler (with toggle outputs) + 8-bit timer/ counter with an 8-bit prescaler (with toggle outputs) Mode 1: 8-bit PWM with an 8-bit prescaler × 2 channels Mode 2: 16-bit timer/counter with an 8-bit prescaler (with toggle outputs) (toggle outputs also possible from the lower-order 8 bits) Mode 3: 16-bit timer with an 8-bit prescaler (with toggle outputs) (The lower-order 8 bits can be used as PWM)
  • Timer 6: 8-bit timer with a 6-bit prescaler (with toggle outputs)
  • Timer 7: 8-bit timer with a 6-bit prescaler (with toggle outputs)
  • Base timer 1) The clock is selectable from the subclock (32.768kHz crystal oscillation), system clock, and timer 0 prescaler output. 2) Interrupts are programmable in 5 different time schemes High-Speed Clock Counter
  • Can count clocks with a maximum clock rate of 20MHz (at a main clock of 10MHz).
  • Can generate output real time. SIO
  • SIO0: 8-bit Synchronous serial interface 1) LSB first/MSB first mode selectable 2) Built-in 8-bit baudrate generator (maximum transfer clock cycle=4/3tCYC)
  • SIO1: 8-bit asynchronous/synchronous serial interface Mode 0: Synchronous 8-bit serial I/O (2- or 3-wire configuration, 2 to 512 tCYC transfer clocks) Mode 1: Asynchronous serial I/O (half-duplex, 8 data bits, 1 stop bit, 8 to 2048 tCYC baudrates) Mode 2: Bus mode 1 (start bit, 8 data bits, 2 to 512 tCYC transfer clocks) Mode 3: Bus mode 2 (start detect, 8 data bits, stop detect) UART
  • Full Duplex
  • 7/8/9 bit data bits selectable
  • 1 stop bit (2 bits in continuous data transmission)
  • Built-in baudrate generator AD Converter: 12 bits/8 bits × 8 channels
  • 12 bits/8 bits AD converter resolution selectable Remote Control Receiver Circuit (sharing pins with P15, SCK1, INT3, and T0IN)
  • Noise rejection function (noise filter time constant selectable from 1 tCYC, 32 tCYC, and 128 tCYC)

No.A1028-4/29 Clock Output Function

  • Can generate clock outputs with a frequency of 1/1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64 of the source clock selected as the system clock.
  • Can generate the source clock for the subclock Watchdog Timer
  • External RC watchdog timer
  • Interrupt and reset signals selectable Interrupts
  • 18 sources, 10 vector addresses 1) Provides three levels (low (L), high (H), and highest (X)) of multiplex interrupt control. Any interrupt requests of the level equal to or lower than the current interrupt are not accepted. 2) When interrupt requests to two or more vector addresses occur at the same time, the interrupt of the highest level takes precedence over the other interrupts. For interrupts of the same level, the interrupt into the smallest vector address takes precedence. No. Vector Address Level Interrupt Source 1 00003H X or L INT0 2 0000BH X or L INT1 3 00013H H or L INT2/T0L/INT4 4 0001BH H or L INT3/base timer 5 00023H H or L T0H 6 0002BH H or L T1L/T1H 7 00033H H or L SIO0/UART1 receive 8 0003BH H or L SIO1/UART1 transmit 9 00043H H or L ADC/T6/T7 10 0004BH H or L Port 0
  • Priority levels X > H > L
  • Of interrupts of the same level, the one with the smallest vector address takes precedence. Subroutine Stack Levels: 128levels (The stack is allocated in RAM.) High-speed Multiplication/Division Instructions
  • 16 bits × 8 bits (5 tCYC execution time)
  • 24 bits × 16 bits (12 tCYC execution time)
  • 16 bits ÷ 8 bits (8 tCYC execution time)
  • 24 bits ÷ 16 bits (12 tCYC execution time) Oscillation Circuits
  • Internal oscillation circuits Low-speed RC oscillation circuit : For system clock (100kHz) Medium-speed RC oscillation circuit : For system clock (1MHz) Multifrequency RC oscillation circuit : For system clock (8MHz)
  • External oscillation circuits Hi-speed CF oscillation circuit: For system clock, with internal Rf Low speed crystal oscillation circuit: For low- speed system clock, with internal Rf 1) The CF and crystal oscillation circuits share the same pins. The active circuit is selected under program control. 2) Both the CF and crystal oscillator circuits stop operation on a system reset. When the reset is released, only the CF oscillation circuit resumes operation. System Clock Divider Function
  • Can run on low current. 76.8μs (at a main clock rate of 10MHz).

No.A1028-5/29 Internal Reset Function

  • Power-on reset (POR) function 1) POR reset is generated only at power-on time. 4.35V) through option configuration.
  • Low-voltage detection reset (LVD) function 1) LVD and POR functions are combined to generate resets when power is turned on and when power voltage falls below a certain level. 2) The use/disuse of the LVD function and the low voltage threshold level (7 levels: 1.91V, 2.01V, 2.31V, 2.51V, Standby Function
  • HALT mode: Halts instruction execution while allowing the peripheral circuits to continue operation. 1) Oscillation is not halted automatically. 2) There are three ways of resetting the HALT mode. (1) Setting the reset pin to the low level (2) System resetting by watchdog timer or low-voltage detection (3) Occurrence of an interrupt
  • HOLD mode: Suspends instruction execution and the operation of the peripheral circuits. 1) The CF, RC, and crystal oscillators automatically stop operation. 2) There are four ways of resetting the HOLD mode. (1) Setting the reset pin to the lower level. (2) System resetting by watchdog timer or low-voltage detection (3) Having an interrupt source established at either INT0, INT1, INT2, INT4 * INT0 and INT1 HOLD mode reset is available only when level detection is set. (4) Having an interrupt source established at port 0.
  • X'tal HOLD mode: Suspends instruction execution and the operation of the peripheral circuits except the base timer. 1) The CF and RC oscillators automatically stop operation. 2) The state of crystal oscillation established when the X'tal HOLD mode is entered is retained. 3) There are five ways of resetting the X'tal HOLD mode. (1) Setting the reset pin to the low level. (2) System resetting by watchdog timer or low-voltage detection. (3) Having an interrupt source established at either INT0, INT1, INT2, INT4 * INT0 and INT1 HOLD mode reset is available only when level detection is set. (4) Having an interrupt source established at port 0. (5) Having an interrupt source established in the base timer circuit. Note: Available only when X’tal oscillation is selected. Onchip Debugger
  • Supports software debugging with the IC mounted on the target board.
  • Two channels of on-chip debugger pins are available to be compatible with small pin count devices. DBGP0 (P0), DBGP1 (P1) Data Security Function (flash versions only)
  • Protects the program data stored in flash memory from unauthorized read or copy. Note: This data security function does not necessarily provide absolute data security. Development Tools
  • On-chip debugger: (1) TCB87 type B + LC87D2G08A (2) TCB87 TypeB + LC87F2G08A (3) TCB87 TypeC (3 wire version) + LC87D2G08A (4) TCB87 TypeC (3 wire version) + LC87F2G08A Note: LC87F2G08A has an On-chip debugger but its function is limited.

No.A1028-6/29 Flash ROM Programming Boards Package Programming boards MFP24S(300mil) W87F2GM MFP24SJ(300mil) W87F2GMJ SSOP24(225mil) W87F2GS VCT24(3.5×3.5) (build-to-order) Flash ROM Programmer Maker Model Supported version Device Flash Support Group, Inc. (FSG) Single Programmer AF9708 AF9709/AF9709B/AF9709C (Including Ando Electric Co., Ltd. models) Rev 02.72 or later LC87F2H08A Gang Programmer AF9723/AF9723B(Main body) (Including Ando Electric Co., Ltd. models) - - AF9833(Unit) (Including Ando Electric Co., Ltd. models) - - Flash Support Group, Inc. (FSG) Our company (Note 1) In-circuit Programmer AF9101/AF9103(Main body) (FSG models) (Note 2) LC87F2G08A SIB87(Inter Face Driver) (Our company model) Our company Single/Gang Programmer SKK/SKK Type B (SanyoFWS) Application Version 1.04 or later Chip Data Version 2.10 or later LC87F2G08A In-circuit/Gang Programmer SKK-DBG Type B (SanyoFWS) For information about AF-Series: Flash Support Group, Inc. TEL: +81-53-459-1050 E-mail: sales@j-fsg.co.jp Note1: On-board-programmer from FSG (AF9101/AF9103) and serial interface driver from Our company (SIB87) together can give a PC-less, standalone on-board-programming capabilities. Note2: It needs a special programming devices and applications depending on the use of programming environment. Please ask FSG or Our company for the information.

No.A1028-7/29 Pin Assignment MFP24S (300mil) “Lead-free Type” MFP24SJ (300mil) “Lead -/Halogen-free Type” SSOP24 (225mil) “Lead-free Type” MFP24S/ MFP24SJ/ SSOP24 NAME MFP24S/ MFP24SJ/ SSOP24 NAME

1 P70/INT0/T0LCP/AN8 13 P16/T1PWML/INT2/T0IN

2 RES 14 P17/T1PWMH/BUZ/INT1/T0HCP

3 V SS1 15 P20/UTX/INT4/T1IN

4 CF1/XT1 16 P21/URX/INT4/T1IN

5 CF2/XT2 17 P00/AN0

6 V DD1 18 P01/AN1

7 P10/SO0 19 P02/AN2

8 P11/SI0/SB0 20 P03/AN3

9 P12/SCK0 21 P04/AN4

10 P13/SO1/DBGP12 22 P05/AN5/CKO/DBGP00

11 P14/SI1/SB1/DBGP11 23 P06/AN6/T6O/DBGP01

12 P15/SCK1/INT3/T0IN/DBGP10 24 P07/T7O/DBGP02

No.A1028-8/29 VCT24(3.5×3.5) “Lead-/Halogen-free Type” (build-to-order) VCT24 NAME VCT24 NAME

1 V SS1 13 P20/UTX/INT4/T1IN

2 CF1/XT1 14 P21/URX/INT4/T1IN

3 CF2/XT2 15 P00/AN0

4 V DD1 16 P01/AN1

5 P10/SO0 17 P02/AN2

6 P11/SI0/SB0 18 P03/AN3

7 P12/SCK0 19 P04/AN4

8 P13/SO1/DBGP12 20 P05/AN5/CKO/DBGP00

9 P14/SI1/SB1/DBGP11 21 P06/AN6/T6O/DBGP01

10 P15/SCK1/INT3/T0IN/DBGP10 22 P07/T7O/DBGP02

11 P16/T1PWML/INT2/T0IN 23 P70/INT0/T0LCP/AN8

12 P17/T1PWMH/BUZ/INT1/T0HCP 24 RES

No.A1028-9/29 System Block Diagram Interrupt control Standby control IR PLA Bus interface Port 0 Port 1 SIO0 SIO1 Timer 0 Timer 1 Port 7 ADC ALU Flash ROM PC ACC B register C register PSW RAR RAM Stack pointer Port 2 INT4 Base timer Timer 6 INT0 to 2 INT3 (Noise filter) Timer 7 On-chip debugger Clock generator CF/ X'tal RC MRC Port 2 Reset control Reset circuit (LVD/POR) WDT RES UART1 SRC

No.A1028-10/29 Pin Description Pin Name I/O Description Option VSS1 - - Power supply pin No VDD1 - + Power supply pin No Port 0 I/O • 8-bit I/O port

  • I/O specifiable in 4-bit units
  • Pull-up resistors can be turned on and off in 4-bit units.
  • HOLD reset input
  • Port 0 interrupt input
  • Pin functions P05: System clock output P06: Timer 6 toggle output P07: Timer 7 toggle output P00(AN0) to P06(AN6): AD converter input P05(DBGP00) to P07(DBGP02): On-chip debugger 0 port Yes P00 to P07 Port 1 I/O • 8-bit I/O port
  • I/O specifiable in 1-bit units
  • Pull-up resistors can be turned on and off in 1-bit units.
  • Pin functions P10: SIO0 data output P11: SIO0 data input/bus I/O P12: SIO0 clock I/O P13: SIO1 data output P14: SIO1 data input / bus I/O P15: SIO1 clock I/O / INT3 input (with noise filter) / timer 0 event input / timer 0H capture input P16: Timer 1PWML output / INT2 input/HOLD reset input/timer 0 event input / timer 0L capture input P17: Timer 1PWMH output / beeper output / INT1 input / HOLD reset input / timer 0H capture input P15(DBGP10) to P13(DBGP12): On-chip-debugger 1 port Interrupt acknowledge type Rising Falling Rising & Falling H level L level INT1 INT2 INT3 enable enable enable enable enable enable disable enable enable enable disable disable enable disable disable Yes P10 to P17 Port 2 I/O • 2-bit I/O port
  • I/O specifiable in 1-bit units
  • Pull-up resistors can be turned on and off in 1-bit units.
  • Pin functions P20: UART transmit P21: UART receive P20 to P21: INT4 input / HOLD reset input / timer 1 event input / timer 0L capture input / timer 0H capture input Interrupt acknowledge types Yes P20 to P21 Rising Falling Rising & Falling H level L level INT4 enable enable enable disable disable Continued on next page.

No.A1028-11/29 Continued from preceding page. Pin Name I/O Description Option Port 7 I/O • 1-bit I/O port

  • I/O specifiable in 1-bit units
  • Pull-up resistors can be turned on and off in 1-bit units.
  • Pin functions P70: INT0 input / HOLD reset input / timer 0L capture input / watchdog timer output P70(AN8): AD converter input Interrupt acknowledge types No P70 Rising Falling Rising & Falling H level L level INT0 enable enable disable enable enable RES I/O External reset input / internal reset output No CF1/XT1 I • Ceramic resonator or 32.768kHz crystal oscillator input pin
  • Pin function General-purpose input port No CF2/XT2 I/O • Ceramic resonator or 32.768kHz crystal oscillator output pin
  • Pin function General-purpose input port No Port Output Types The table below lists the types of port outputs and the presence/absence of a pull-up resistor. Data can be read into any input port even if it is in the output mode. Port Name Option selected in units of Option type Output type Pull-up resistor P00 to P07 1 bit 1 CMOS Programmable (Note 1)

2 Nch-open drain No

P10 to P17 1 bit 1 CMOS Programmable

2 Nch-open drain Programmable

P20 to P21 1 bit 1 CMOS Programmable P70 - No Nch-open drain Programmable Note 1: The control of the presence or absence of the programmable pull-up resistors for port 0 and the switching between low-and high-impedance pull-up connection is exercised in nibble (4-bit) units (P00 to 03 or P04 to 07).

No.A1028-12/29 User Option Table Option Name Option to be Applied on Flash-ROM Ve rsion Option Selected in Units of Option Selection Port output type P00 to P07  1 bit CMOS Nch-open drain P10 to P17  1 bit CMOS Nch-open drain P20 to P21  1 bit CMOS Nch-open drain Program start address -  - 00000h 01E00h Low-voltage detection reset function Detect function  - Enable:Use Disable:Not Used Detect level  - 7-level Power-on reset function Power-On reset level  - 8-level Recommended Unused Pin Connections Port Name Recommended Unused Pin Connections Board Software P00 to P07 Open Output low P10 to P17 Open Output low P20 to P21 Open Output low P70 Open Output low CF1/XT1 Pulled low with a 100k Ω resistor or less General-purpose input port CF2/XT2 Pulled low with a 100k Ω resistor or less General-purpose input port Notes on CF1/XT1 and CF2/XT2 pins

  • When using as general-purpose input ports Since the CF1/XT1 and CF2/XT2 pins are configured as CF oscillator pins at system reset time, it is necessary to add a current limiting resistor of 1kΩ or greater to the CF2/XT2 pin in series when using them as general-purpose input pins.
  • Differences between flash and mask ROM version System Reset Time State After System Reset is Released Flash ROM version LC87F2G08A CF1/XT1 Set high via the internal Rf resistor CF oscillation state CF2/XT2 Set high CF oscillation state Mask ROM version LC872G08A/06A/04A CF1/XT1 Set low via the internal Rf resistor CF oscillation state CF2/XT2 Set low CF oscillation state On-chip Debugger Pin Connection Requirements For the treatment of the on-chip debugger pins, refer to the separately available documents entitled "RD87 on-chip debugger installation manual" and "LC872000 series on-chip debugger pin connection requirements"

No.A1028-13/29 Parameter Symbol Pin/Remarks Conditions Specification VDD[V] min typ max unit Maximum supply voltage VDD max V DD1 -0.3 +6.5 V Input voltage V I CF1, CF2 -0.3 V DD+0.3 Input/output voltage VIO Ports 0, 1, 2, P70 -0.3 V DD+0.3 High level output current Peak output current IOPH Ports 0, 1, 2 CMOS output select Per 1 applicable pin -10 mA Mean output current (Note 1-1) IOMH Ports 0, 1, 2 CMOS output select Per 1 applicable pin -7.5 Total output current ΣIOAH(1) P10 to P14 Total of all applicable pins -20 ΣIOAH(2) Ports 0, 2 P15 to P17 Total of all applicable pins -20 ΣIOAH(3) Ports 0, 1, 2 Total of all applicable pins -25 Low level output current Peak output current IOPL(1) P02 to P07 Ports 1, 2 Per 1 applicable pin 2 0 IOPL(2) P00, P01 Per 1 applicable pin 3 0 IOPL(3) P70 Per 1 applicable pin 1 0 Mean output current (Note 1-1) IOML(1) P02 to P07 Ports 1, 2 Per 1 applicable pin 1 5 IOML(2) P00, P01 Per 1 applicable pin 2 0 IOML(3) P70 Per 1 applicable pin 7.5 Total output current ΣIOAL(1) P10 to P14 Total of all applicable pins 5 0 ΣIOAL(2) Port 0, 2, P15 to P17 Total of all applicable pins 6 0 ΣIOAL(3) Ports 0, 1, 2 Total of all applicable pins 7 0 ΣIOAL(4) P70 Total of all applicable pins 7.5 Power Dissipation Pd max(1) MFP24S(300mil) Ta=-40 to +85 °C Package only 129 mW Pd max(2) Ta=-40 to +85 °C Package with thermal resistance board (Note 1-2) 229 Pd max(3) MFP24SJ(300mil) Ta=-40 to +85 °C Package only 171 Pd max(4) Ta=-40 to +85 °C Package with thermal resistance board (Note 1-2) 393 Pd max(5) SSOP24(225mil) Ta=-40 to +85 °C Package only 111 Pd max(6) Ta=-40 to +85 °C Package with thermal resistance board (Note 1-2) 334 Pd max(7) VCT24(3.5 ×3.5) Ta=-40 to +85 °C Package only T.B.D Pd max(8) Ta=-40 to +85 °C Package with thermal resistance board T.B.D Operating ambient temperature Topr -40 +85 Storage ambient temperature Tstg -55 +125 Note 1-1: The mean output current is a mean value measured over 100ms. Note 1-2: SEMI standards thermal resistance board (size: 76.1×114.3×1.6tmm, glass epoxy) is used. Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Oper ating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.

No.A1028-14/29 Allowable Operating Conditions at Ta = -40°C to +85°C, VSS1 = 0V Parameter Symbol Pin/Remarks Conditions Specification VDD[V] min typ max unit Operating supply voltage (Note 2-1) VDD(1) V DD1 0.245 μs ≤ tCYC ≤ 200μs 2.7 5.5 V VDD(2) 0.294 μs ≤ tCYC ≤ 200μs 2.2 5.5 VDD(3) 0.735 μs ≤ tCYC ≤ 200μs 1.8 5.5 Memory sustaining supply voltage VHD V DD1 RAM and register contents sustained in HOLD mode. 1.6 High level input voltage VIH(1) Ports 1, 2, P70 port input/ interrupt side 1.8 to 5.5 0.3VDD+0.7 V DD VIH(2) Ports 0 1.8 to 5.5 0.3VDD+0.7 V DD VIH(3) Port 70 watchdog timer side 1.8 to 5.5 0.9V DD V DD VIH(4) CF1, RES 1.8 to 5.5 0.75V DD V DD Low level input voltage VIL(1) Ports 1, 2, P70 port input/ interrupt side 4.0 to 5.5 V SS 0.1VDD+0.4 1.8 to 4.0 V SS 0.2V DD VIL(2) Ports 0 4.0 to 5.5 V SS 0.15VDD+0.4 1.8 to 4.0 V SS 0.2V DD VIL(3) Port 70 watchdog timer side 1.8 to 5.5 V SS 0.8VDD-1.0 VIL(4) CF1, RES 1.8 to 5.5 V SS 0.25VDD Instruction cycle time (Note 2-1) tCYC (Note 2-2) 2.7 to 5.5 0.245 200 μs 2.2 to 5.5 0.294 200 1.8 to 5.5 0.735 200 External system clock frequency FEXCF CF1 • CF2 pin open

  • System clock frequency division ratio=1/1
  • External system clock duty=50±5% 2.7 to 5.5 0.1 12 MHz 1.8 to 5.5 0.1 4
  • CF2 pin open
  • System clock frequency division ratio=1/2
  • External system clock duty=50±5% 3.0 to 5.5 0.2 24.4 2.0 to 5.5 0.2 8 Oscillation frequency range (Note 2-3) FmCF(1) CF1, CF2 12MHz ceramic oscillation. See Fig. 1. 2.7 to 5.5 12 MHz FmCF(2) CF1, CF2 10MHz ceramic oscillation. See Fig. 1. 2.2 to 5.5 10 FmCF(3) CF1, CF2 4MHz ceramic oscillation. CF oscillation normal amplifier size selected. (CFLAMP=0) See Fig. 1. 1.8 to 5.5 4 4MHz ceramic oscillation. CF oscillation low amplifier size selected. (CFLAMP=1) See Fig. 1. 2.2 to 5.5 4 FmMRC Frequency variable RC oscillation. 1/2 frequency division ration. (RCCTD=0) (Note 2-4) FmSRC Internal low-speed RC oscillation 1.8 to 5.5 50 100 200 kHzFsX’tal XT1, XT2 32.768kHz crystal oscillation Note 2-1: VDD must be held greater than or equal to 2.2V in the flash ROM onboard programming mode. Note 2-2: Relationship between tCYC and oscillation frequency is 3/FmCF at a division ratio of 1/1 and 6/FmCF at a division ratio of 1/2. Note 2-3: See Tables 1 and 2 for the oscillation constants. Note 2-4: When switching the system clock, allow an oscillation stabilization time of 100μs or longer after the multifrequency RC oscillator circuit transmits from the "oscillation stopped" to "oscillation enabled" state.

No.A1028-15/29 Parameter Symbol Pin/Remarks Conditions Specification VDD[V] min typ max unit High level input current IIH(1) Ports 0, 1, 2, P70, RES Output disabled Pull-up resistor off VIN=VDD (Including output Tr's off leakage current) 1.8 to 5.5 1 μA IIH(2) CF1 V IN=VDD 1.8 to 5.5 15 Low level input current IIL(1) Ports 0, 1, 2, P70, RES Output disabled Pull-up resistor off VIN=VSS (Including output Tr's off leakage current) 1.8 to 5.5 -1 IIL(2) CF1 V IN=VSS 1.8 to 5.5 -15 High level output voltage VOH(1) Ports 0, 1, 2 I OH=-1mA 4.5 to 5.5 V DD-1 V VOH(2) I OH=-0.35mA 2.7 to 5.5 V DD-0.4 VOH(3) I OH=-0.15mA 1.8 to 5.5 V DD-0.4 Low level output voltage VOL(1) Ports 0, 1, 2 I OL=10mA 4.5 to 5.5 1.5 VOL(2) I OL=1.4mA 2.7 to 5.5 0.4 VOL(3) I OL=0.8mA 1.8 to 5.5 0.4 VOL(4) P70 I OL=1.4mA 2.7 to 5.5 0.4 VOL(5) I OL=0.8mA 1.8 to 5.5 0.4 VOL(6) P00, P01 I OL=25mA 4.5 to 5.5 1.5 VOL(7) I OL=4mA 2.7 to 5.5 0.4 VOL(8) I OL=2mA 1.8 to 5.5 0.4 Pull-up resistance Rpu(1) Ports 0, 1, 2 P70 VOH=0.9VDD When Port 0 selected low-impedance pull-up. 4.5 to 5.5 15 35 80 kΩ Rpu(2) 1.8 to 4.5 18 50 230 Rpu(3) Port 0 V OH=0.9VDD When Port 0 selected high-impedance pull-up. 1.8 to 5.5 100 210 400 Hysteresis voltage VHYS (1) Ports 1, 2, P70, RES 2.7 to 5.5 0.1VDD V VHYS(2) 1.8 to 2.7 0.07VDD Pin capacitance CP All pins For pins other than that under test: VIN=VSS f=1MHz Ta=25°C 1.8 to 5.5 10 pF

No.A1028-16/29 Serial I/O Characteristics at Ta = -40°C to +85°C, VSS1 = 0V 1. SIO0 Serial I/O Characteristics (Note 4-1-1) Parameter Symbol Pin/ Remarks Conditions Specification VDD[V] min typ max unit Serial clock Input clock Frequency tSCK(1) SCK0(P12) • See Fig. 5. 1.8 to 5.5 tCYC Low level pulse width tSCKL(1) 1 High level pulse width tSCKH(1) Output clock Frequency tSCK(2) SCK0(P12) • CMOS output selected

  • See Fig. 5. 1.8 to 5.5 Low level pulse width tSCKL(2) tSCK High level pulse width tSCKH(2) 1/2 Serial input Data setup time tsDI(1) SB0(P11), SI0(P11)
  • Must be specified with respect to rising edge of SIOCLK.
  • See Fig. 5. 1.8 to 5.5 0.05 μs Data hold time thDI(1) 0.05 Serial output Input clock Output delay time tdD0(1) SO0(P10), SB0(P11)
  • Continuous data transmission/reception mode (Note 4-1-2) 1.8 to 5.5 (1/3)tCYC +0.08 tdD0(2) • Synchronous 8-bit mode (Note 4-1-2) 1tCYC +0.08 Output clock tdD0(3) (Note 4-1-2) (1/3)tCYC +0.08 Note 4-1-1: These specifications are theoretical values. Add margin depending on its use. Note 4-1-2: Must be specified with respect to falling edge of SIOCLK. Must be specified as the time to the beginning of output state change in open drain output mode. See Fig. 5. 2. SIO1 Serial I/O Characteristics (Note 4-2-1) Parameter Symbol Pin/ Remarks Conditions Specification VDD[V] min typ max unit Serial clock Input clock Frequency tSCK(3) SCK1(P15) See Fig. 5. 1.8 to 5.5 tCYC Low level pulse width tSCKL(3) 1 High level pulse width tSCKH(3) 1 Output clock Frequency tSCK(4) SCK1(P15) • CMOS output selected
  • See Fig. 5. 1.8 to 5.5 Low level pulse width tSCKL(4) 1/2 tSCK High level pulse width tSCKH(4) 1/2 Serial input Data setup time tsDI(2) SB1(P14), SI1(P14)
  • Must be specified with respect to rising edge of SIOCLK.
  • See Fig. 5. 1.8 to 5.5 0.05 μs Data hold time thDI(2) 0.05 Serial output Output delay time tdD0(4) SO1(P13), SB1(P14)
  • Must be specified with respect to falling edge of SIOCLK.
  • Must be specified as the time to the beginning of output state change in open drain output mode.
  • See Fig. 5. 1.8 to 5.5 (1/3)tCYC +0.08 Note 4-2-1: These specifications are theoretical values. Add margin depending on its use.

No.A1028-17/29 Pulse Input Conditions at Ta = -40°C to +85°C, VSS1 = 0V Parameter Symbol Pin/Remarks Conditions Specification VDD[V] min typ max unit High/low level pulse width tPIH(1) tPIL(1) INT0(P70), INT1(P17), INT2(P16), INT4(P20 to P21)

  • Interrupt source flag can be set.
  • Event inputs for timer 0 or 1 are enabled. 1.8 to 5.5 1 tCYC tPIH(2) tPIL(2) INT3(P15) when noise filter time constant is
  • Interrupt source flag can be set.
  • Event inputs for timer 0 are enabled. 1.8 to 5.5 2 tPIH(3) tPIL(3) INT3(P15) when noise filter time constant is
  • Interrupt source flag can be set.
  • Event inputs for timer 0 are nabled. 1.8 to 5.5 64 tPIH(4) tPIL(4) INT3(P15) when noise filter time constant is
  • Interrupt source flag can be set.
  • Event inputs for timer 0 are enabled. 1.8 to 5.5 256 tPIL(5) RES • Resetting is enabled. 1.8 to 5.5 200 μs

No.A1028-18/29 AD Converter Characteristics at VSS1 = 0V <12bits AD Converter Mode/Ta = -40°C to +85°C > Parameter Symbol Pin/Remarks Conditions Specification VDD[V] min typ max unit Resolution N AN0(P00) to AN6(P06) AN8(P70) 2.4 to 5.5 12 bit Absolute accuracy ET (Note 6-1) 3.0 to 5.5 ±16 LSB (Note 6-1)

  • Ta=-10 to +50°C 2.4 to 3.6 ±20 Conversion time TCAD • See Conversion time calculation formulas. (Note 6-2) 4.0 to 5.5 32 115 μs 3.0 to 5.5 64 115
  • See Conversion time calculation formulas. (Note 6-2)
  • Ta=-10 to +50°C 2.4 to 3.6 410 425 Analog input voltage range VAIN 2.4 to 5.5 V SS V DD V Analog port input current IAINH VAIN=V DD 2.4 to 5.5 1 μA IAINL VAIN=V SS 2.4 to 5.5 -1 <8bits AD Converter Mode/Ta = -40°C to +85°C > Parameter Symbol Pin/Remarks Conditions Specification VDD[V] min typ max unit Resolution N AN0(P00) to AN6(P06) AN8(P70) 2.4 to 5.5 8 bit Absolute accuracy ET (Note 6-1) 2.4 to 5.5 ±1.5 LSB Conversion time TCAD • See Conversion time calculation formulas. (Note 6-2) 4.0 to 5.5 20 90 μs 3.0 to 5.5 40 90
  • See Conversion time calculation formulas. (Note 6-2)
  • Ta=-10 to +50°C 2.4 to 3.6 250 265 Analog input voltage range VAIN 2.4 to 5.5 V SS V DD V Analog port input current IAINH VAIN=V DD 2.4 to 5.5 1 μA IAINL VAIN=V SS 2.4 to 5.5 -1 Note 6-1: The quantization error (±1/2LSB) must be excluded from the absolute accuracy. The absolute accuracy must be measured in the microcontroller's state in which no I/O operations occur at the pins adjacent to the analog input channel. Note 6-2: The conversion time refers to the period from the time an instruction for starting a conversion process till the time the conversion results register(s) are loaded with a complete digital conversion value corresponding to the analog input value. The conversion time is 2 times the normal-time conversion time when:
  • The first AD conversion is performed in the 12-bit AD conversion mode after a system reset.
  • The first AD conversion is performed after the AD conversion mode is switched from 8-bit to 12-bit conversion mode. Conversion time calculation formulas: 12bits AD Converter Mode: TCAD(Conversion time) = ((52/(AD division ratio))+2)×(1/3)×tCYC 8bits AD Converter Mode: TCAD(Conversion time) = ((32/(AD division ratio))+2)×(1/3)×tCYC External oscillation (FmCF) Operating supply voltage range (VDD) System division ratio (SYSDIV) Cycle time (tCYC) AD division ratio (ADDIV) AD conversion time (TCAD) 12bit AD 8bit AD CF-12MHz 4.0V to 5.5V 1/1 250ns 1/8 34.8 μs 21.5 μs 3.0V to 5.5V 1/1 250ns 1/16 69.5 μs 42.8 μs CF-10MHz 4.0V to 5.5V 1/1 300ns 1/8 41.8 μs 25.8 μs 3.0V to 5.5V 1/1 300ns 1/16 83.4 μs 51.4 μs CF-4MHz 3.0V to 5.5V 1/1 750ns 1/8 104.5 μs 64.5 μs 2.4V to 3.6V 1/1 750ns 1/32 416.5 μs 256.5 μs

No.A1028-19/29 Power-on Reset (POR) Characteristics at Ta = -40°C to +85°C, VSS1 = 0V Parameter Symbol Pin/Remarks Conditions Specification Option selected voltage min typ max unit POR release voltage PORRL • Select from option. (Note 7-1) 1.67V 1.55 1.67 1.79 V 1.97V 1.85 1.97 2.09 2.07V 1.95 2.07 2.19 2.37V 2.25 2.37 2.49 2.57V 2.45 2.57 2.69 2.87V 2.75 2.87 2.99 3.86V 3.73 3.86 3.99 4.35V 4.21 4.35 4.49 Detection voltage unknown state POUKS • See Fig. 7. Power supply rise time PORIS • Power supply rise time from 0V to 1.6V. 100 ms Note7-1: The POR release level can be selected out of 8 levels only when the LVD reset function is disabled. Note7-2: POR is in an unknown state before transistors start operation. Low Voltage Detection Reset (LVD) Characteristics at Ta = -40°C to +85°C, VSS1=0V Parameter Symbol Pin/Remarks Conditions Specification Option selected voltage min typ max unit LVD reset voltage (Note 8-2) LVDET • Select from option. (Note 8-1) (Note 8-3)

  • See Fig. 8. 1.91V 1.81 1.91 2.01 V 2.01V 1.91 2.01 2.11 2.31V 2.21 2.31 2.41 2.51V 2.41 2.51 2.61 2.81V 2.71 2.81 2.91 3.79V 3.69 3.79 3.89 4.28V 4.18 4.28 4.38 LVD hysteresys width LVHYS 1.91V 55 mV 2.01V 55 2.31V 55 2.51V 55 2.81V 60 3.79V 65 4.28V 65 Detection voltage unknown state LVUKS • See Fig. 8. (Note 8-4) 0.7 0.95 V Low voltage detection minimum width (Reply sensitivity) TLVDW • LVDET-0.5V
  • See Fig. 9. 0.2 ms Note8-1: The LVD reset level can be selected out of 7 levels only when the LVD reset function is enabled. Note8-2: LVD reset voltage specification values do not include hysteresis voltage. Note8-3: LVD reset voltage may exceed its specification values when port output state changes and/or when a large current flows through port. Note8-4: LVD is in an unknown state before transistors start operation.

No.A1028-20/29 Consumption Current Characteristics at Ta = -40°C to +85°C, VSS1 = 0V Parameter Symbol Pin/ Remarks Conditions Specification VDD[V] min typ max unit Normal mode consumption current (Note 9-1) (Note 9-2) IDDOP(1) V DD1 • FmCF=12MHz ceramic oscillation mode

  • System clock set to 12MHz side
  • Internal low speed and medium speed RC oscillation stopped.
  • Frequency variable RC oscillation stopped.
  • 1/1 frequency division ratio 2.7 to 5.5 7.4 13.0 mA 2.7 to 3.6 4.4 8.1 IDDOP(2) • CF1=24MHz external clock
  • System clock set to CF1 side
  • Internal low speed and medium speed RC oscillation stopped.
  • Frequency variable RC oscillation stopped.
  • 1/2 frequency division ratio 3.0 to 5.5 9.7 16.2 3.0 to 3.6 5.3 8.7 IDDOP(3) • FmCF=10MHz ceramic oscillation mode
  • System clock set to 10MHz side
  • Internal low speed and medium speed RC oscillation stopped.
  • Frequency variable RC oscillation stopped.
  • 1/1 frequency division ratio 2.2 to 5.5 6.6 11.9 2.2 to 3.6 4.0 7.4 IDDOP(4) • FmCF=4MHz ceramic oscillation mode
  • System clock set to 4MHz side
  • Internal low speed and medium speed RC oscillation stopped.
  • Frequency variable RC oscillation stopped.
  • 1/1 frequency division ratio 1.8 to 5.5 2.9 6.5 1.8 to 3.6 2.2 4.2 IDDOP(5) • CF oscillation low amplifier size selected. (CFLAMP=1)
  • FmCF=4MHz ceramic oscillation mode
  • System clock set to 4MHz side
  • Internal low speed and medium speed RC oscillation stopped.
  • Frequency variable RC oscillation stopped.
  • 1/4 frequency division ratio 2.2 to 5.5 1.1 2.5 2.2 to 3.6 0.6 1.3 IDDOP(6) • FsX’tal=32.768kHz crystal oscillation mode
  • Internal low speed RC oscillation stopped.
  • System clock set to internal medium speed RC oscillation.
  • Frequency variable RC oscillation stopped.
  • 1/2 frequency division ratio 1.8 to 5.5 0.6 1.7 1.8 to 3.6 0.3 0.9 IDDOP(7) • FsX’tal=32.768kHz crystal oscillation mode
  • Internal low speed and medium speed RC oscillation stopped.
  • System clock set to 8MHz with frequency variable RC oscillation
  • 1/1 frequency division ratio 2.7 to 5.5 5.0 9.1 2.7 to 3.6 3.6 5.8 IDDOP(8) • External FsX’tal and FmCF oscillation stopped.
  • System clock set to internal low speed RC oscillation.
  • Internal medium speed RC oscillation sopped.
  • Frequency variable RC oscillation stopped.
  • 1/1 frequency division ratio 1.8 to 5.5 75 370 μA 1.8 to 3.6 46 192 IDDOP(9) • External FsX’tal and FmCF oscillation stopped.
  • System clock set to internal low speed RC oscillation.
  • Internal medium speed RC oscillation stopped.
  • Frequency variable RC oscillation stopped.
  • 1/1 frequency division ratio
  • Ta=-10 to +50°C 5.0 75 176 3.3 46 115 2.5 35 85 Note9-1: Values of the consumption current do not include current that flows into the output transistors and internal pull-up resistors. Note9-2: The consumption current values do not include operational current of LVD function if not specified. Continued on next page.

No.A1028-21/29 Continued from preceding page. Parameter Symbol Pin/ Remarks Conditions Specification VDD[V] min typ max unit Normal mode consumption current (Note 9-1) (Note 9-2) IDDOP(10) V DD1 • FsX’tal=32.768kHz crystal oscillation mode

  • System clock set to 32.768kHz side
  • Internal low speed and medium speed RC oscillation stopped.
  • Frequency variable RC oscillation stopped.
  • 1/2 frequency division ratio 1.8 to 5.5 38 139 μA 1.8 to 3.6 15 66 IDDOP(11) • FsX’tal=32.768kHz crystal oscillation mode
  • System clock set to 32.768kHz side
  • Internal low speed and medium speed RC oscillation stopped.
  • Frequency variable RC oscillation stopped.
  • 1/2 frequency division ratio
  • Ta=-10 to +50°C 5.0 38 101 3.3 15 46 2.5 9.0 28 HALT mode consumption current (Note 9-1) (Note 9-2) IDDHALT(1) • HALT mode
  • FmCF=12MHz ceramic oscillation mode
  • System clock set to 12MHz side
  • Internal low speed and medium speed RC oscillation stopped.
  • Frequency variable RC oscillation stopped.
  • 1/1 frequency division ratio 2.7 to 5.5 3.1 5.6 mA 2.7 to 3.6 1.6 2.9 IDDHALT(2) • HALT mode
  • CF1=24MHz external clock
  • System clock set to CF1 side
  • Internal low speed and medium speed RC oscillation stopped.
  • Frequency variable RC oscillation stopped.
  • 1/2 frequency division ratio 3.0 to 5.5 4.9 8.6 3.0 to 3.6 2.3 3.8 IDDHALT(3) • HALT mode
  • FmCF=10MHz ceramic oscillation mode
  • System clock set to 10MHz side
  • Internal low speed and medium speed RC oscillation stopped.
  • Frequency variable RC oscillation stopped.
  • 1/1 frequency division ratio 2.2 to 5.5 2.7 5.3 2.2 to 3.6 1.4 2.6 IDDHALT(4) • HALT mode
  • FmCF=4MHz ceramic oscillation mode
  • System clock set to 4MHz side
  • Internal low speed and medium speed RC oscillation stopped.
  • Frequency variable RC oscillation stopped.
  • 1/1 frequency division ratio 1.8 to 5.5 1.4 3.5 1.8 to 3.6 0.7 1.3 IDDHALT(5) • HALT mode
  • CF oscillation low amplifier size selected. (CFLAMP=1)
  • FmCF=4MHz ceramic oscillation mode
  • System clock set to 4MHz side
  • Internal low speed and medium speed RC oscillation stopped.
  • Frequency variable RC oscillation stopped.
  • 1/4 frequency division ratio 2.2 to 5.5 0.7 1.8 2.2 to 3.6 0.3 0.7 IDDHALT(6) • HALT mode
  • FsX’tal=32.768kHz crystal oscillation mode
  • Internal low speed RC oscillation stopped.
  • System clock set to internal medium speed RC oscillation
  • Frequency variable RC oscillation stopped.
  • 1/2 frequency division ratio 1.8 to 5.5 0.4 1.1 1.8 to 3.6 0.2 0.5 Note9-1: Values of the consumption current do not include current that flows into the output transistors and internal pull-up resistors. Note9-2: The consumption current values do not include operational current of LVD function if not specified. Continued on next page.

No.A1028-22/29 Continued from preceding page. Parameter Symbol Pin/ remarks Conditions Specification VDD[V] min typ max unit HALT mode consumption current (Note 9-1) (Note 9-2) IDDHALT(7) V DD1 • HALT mode

  • FsX’tal=32.768kHz crystal oscillation mode
  • Internal low speed and medium speed RC oscillation stopped.
  • System clock set to 8MHz with frequency variable RC oscillation
  • 1/1 frequency division ratio 2.7 to 5.5 1.8 3.5 mA 2.7 to 3.6 1.1 2.0 IDDHALT(8) • HALT mode
  • External FsX’tal and FmCF oscillation stopped.
  • System clock set to internal low speed RC oscillation.
  • Internal medium speed RC oscillation stopped.
  • Frequency variable RC oscillation stopped.
  • 1/1 frequency division ratio 1.8 to 5.5 23 260 μA 1.8 to 3.6 13 119 IDDHALT(9) • HALT mode
  • External FsX’tal and FmCF oscillation stopped.
  • System clock set to internal low speed RC oscillation.
  • Internal medium speed RC oscillation stopped.
  • Frequency variable RC oscillation stopped.
  • 1/1 frequency division ratio
  • Ta=-10 to +50°C 5.0 23 65 3.3 13 35 2.5 9.2 25 IDDHALT(10) • HALT mode
  • FsX’tal=32.768kHz crystal oscillation mode
  • System clock set to 32.768kHz side
  • Internal low speed and medium speed RC oscillation stopped.
  • Frequency variable RC oscillation stopped.
  • 1/2 frequency division ratio 1.8 to 5.5 25 112 1.8 to 3.6 8.5 56 IDDHALT(11) • HALT mode
  • FsX’tal=32.768kHz crystal oscillation mode
  • System clock set to 32.768kHz side
  • Internal low speed and medium speed RC oscillation stopped.
  • Frequency variable RC oscillation stopped.
  • 1/2 frequency division ratio
  • Ta=-10 to +50°C 5.0 25 69 3.3 8.5 29 2.5 4.2 15 HOLD mode consumption current (Note 9-1) (Note 9-2) IDDHOLD(1) HOLD mode
  • CF1=VDD or open (External clock mode) 1.8 to 5.5 0.04 30 1.8 to 3.6 0.02 21 IDDHOLD(2) HOLD mode
  • CF1=VDD or open (External clock mode)
  • Ta=-10 to +50°C 5.0 0.04 2.3 3.3 0.02 1.5 2.5 0.017 1.2 IDDHOLD(3) HOLD mode
  • CF1=VDD or open (External clock mode)
  • LVD option selected 1.8 to 5.5 3.2 35 1.8 to 3.6 2.7 24 IDDHOLD(4) HOLD mode
  • CF1=VDD or open (External clock mode)
  • Ta=-10 to +50°C
  • LVD option selected 5.0 3.2 6.5 3.3 2.7 4.5 2.5 2.5 4.2 Timer HOLD mode consumption current (Note 9-1) (Note 9-2) IDDHOLD(5) Timer HOLD mode
  • FsX’tal=32.768 kHz crystal oscillation mode 1.8 to 5.5 22 106 1.8 to 3.6 7.5 45 IDDHOLD(6) Timer HOLD mode
  • FsX’tal=32.768kHz crystal oscillation mode
  • Ta=-10 to +50°C 5.0 22 62 3.3 7.5 23 2.5 2.9 12 Note9-1: Values of the consumption current do not include current that flows into the output transistors and internal pull-up resistors. Note9-2: The consumption current values do not include operational current of LVD function if not specified.

No.A1028-23/29 F-ROM Programming Characteristics at Ta = +10°C to +55°C, VSS1 = 0V Parameter Symbol Pin/Remarks Conditions Specification VDD[V] min typ max unit Onboard programming current IDDFW(1) V DD1 • Only current of the Flash block. 2.2 to 5.5 5 10 mA Programming time tFW(1) • Erasing time 2.2 to 5.5 20 30 ms tFW(2) • Programming time 40 60 µs UART (Full Duplex) Operating Conditions at Ta = -40°C to +85°C, VSS1 = 0V Parameter Symbol Pin/Remarks Conditions Specification VDD[V] min typ max unit Transfer rate UBR UTX(P20) URX(P21) 1.8 to 5.5 16/3 8192/3 tCYC Data length: 7/8/9 bits (LSB first) Stop bits : 1 bit (2-bit in continuous data transmission) Parity bits: None Example of Continuous 8-bit Data Transmission Mode Processing (First Transmit Data=55H) Example of Continuous 8-bit Data Reception Mode Processing (First Receive Data=55H) Transmit data (LSB first) Start of transmission End of transmission UBR Start bit Stop bit Receive data (LSB first) UBR Start of reception End of reception Stop bit Start bit

No.A1028-24/29 Characteristics of a Sample Main System Clock Oscillation Circuit Given below are the characteristics of a sample main system clock oscillation circuit that are measured using a Our designated oscillation characteristics evaluation board and external components with circuit constant values with which the oscillator vendor confirmed normal and stable oscillation. Table 1 Characteristics of a Sample Main System Clock Oscillator Circuit with a Ceramic Oscillator

  • CF oscillation normal amplifier size selected (CFLAMP=0) MURATA Nominal Frequency Type Oscillator Name Circuit Constant Operating Voltage Range [V] Oscillation Stabilization Time Remarks [pF] [pF] Rf [Ω] Rd [Ω] typ [ms] max [ms] Internal C1, C2 10MHz SMD CSTCE10M0G52-R0 (10) (10) Open 680 2.2 to 3.6 0.1 0.5 8MHz LEAD CSTLS8M00G53-B0 (15) (15) 6MHz 4MHz SMD CSTCR4M00G53-R0 (15) (15)
  • CF oscillation low amplifier size selected (CFLAMP=1) MURATA Nominal Frequency Type Oscillator Name Circuit Constant Operating Voltage Range [V] Oscillation Stabilization Time Remarks [pF] [pF] Rf [Ω] Rd [Ω] typ [ms] max [ms] 4MHz SMD CSTCR4M00G53-R0 (15) (15) Internal C1,C2 LEAD CSTLS4M00G53-B0 (15) (15) The oscillation stabilization time refers to the time interval that is required for the oscillation to get stabilized after VDD goes above the operating voltage lower limit (see Figure 3).

No.A1028-26/29 HOLD Reset Signal and Oscillation Stabilization Time Note: External oscillation circuit is selected. Figure 3 Oscillation Stabilization Times Reset Time and Oscillation Stabilization Time Power supply RES Internal medium speed RC oscillation CF1, CF2 Operating mode Reset time Unpredictable Reset Instruction execution VDD Operating VDD lower limit tmsCF/tmsX’tal Internal medium speed RC oscillation or low speed RC oscillation CF1, CF2 (Note) HOLD reset signal HOLD reset signal absent tmsCF/tmsX’tal HOLD HALT HOLD reset signal valid State

No.A1028-29/29 Figure 9 Low voltage detection minimum width (Example of momentary power loss/Voltage variation waveform) PS VDD LVD reset voltage TLVDW VSS LVD release voltage LVDET-0.5V ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequentia l or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s techn ical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC productsfor any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, anddistributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture oft h e part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.