LC79430KNE ONSEMI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

Features

  • On-chip LCD drive circuit (80 bits)
  • Display duty selection ranging from 1/64 to 1/256
  • On-chip input/output pins support a further increases in bit number
  • Supports externally supplied bias voltage
  • On-chip 80-bit bidirectional shift register (supports 40-bit × 2 division)
  • Supports single mode (80-bit shift register) and dual mode (40-bit × 2 shift register) applications (1) O1 → O80 (2) O80 → O1 (3) O1 → O40 and O41 → O80 (4) O80 → O41 and O40 → O1 All four of the shift direction selection listed above all supported
  • Operating power supply voltage/operating temperature include VDD (Logic section) : 2.7 to 5.5V/-20 to +85°C VDD-VEE (LCD section) : 12 to 32V/-20 to +85°C
  • CMOS process
  • 100-pin flat plastic package (QIP100E) CMOS LSI Dot-Matrix LCD Drivers Single mode Dual mode

No. A2123-2/7 Specifications Absolute Maximum Ratings at Ta = 25±2°C, VSS = 0V Parameter Symbol Conditions Ratings unit Maximum supply voltage (Logic) V DD max -0.3 to +7.0 V Maximum supply voltage (LCD) V DD-VEE max *1 0 to 35 V Maximum input voltage V I max -0.3 to V DD+0.3 V Storage temperature Tstg -40 to +125 °C Note *1 The following relations between elements should be maintained: VDD≥V1>V2>V5>VEE, VDD-V2≤7V, V5-VEE≤7V Allowable Operating Ranges at Ta = -20 to +85°C, VSS = 0V Parameter Symbol Conditions min typ max unit Supply voltage (Logic) VDD 2.7 5.5 V Supply voltage (LCD) VDD-VEE *2, 3 12 32 V Input high level voltage V IH DIO1, DIO80, CP, M, DMIN, MODE, RS/LS, DISPOFF 0.8VDD V Input low level voltage V IL DIO1, DIO80, CP, M, DMIN, MODE, RS/LS, DISPOFF 0.2V DD V CP Shift clock f CP CP 1 MHz CP pulse width t WC CP 63 ns Setup time t SETUP DIO1 → CP, DIO80 → CP, DMIN → CP 100 ns Hold time tHOLD DIO1 → CP, DIO80 → CP, DMIN → CP 100 ns CP rise time t R CP 50 ns CP fall time t F CP 50 ns Note *2 The following relations between elements should be maintained: VDD≥V1>V2>V5>VEE, VDD-V2≤7V, V5-VEE≤7V *3 When the power supply is turned on, power to the LCD driver is turned on after or simultaneously with the turning on of the logic section’s power supply. When the power supply is turned off, the logic power supply is turned off after or at the same time the LCD driver power supply is turned off. Electrical Characteristics at Ta = 25±2°C, VDD = 2.7 to 5.5V Parameter Symbol Conditions min typ max unit Input high level current I IH V IN=VDD, VDD=5.5V, DIO1, DIO80, CP, M, DMIN, MODE, RS/LS, DISPOFF 1 μA Input low level current I IL V IN=VSS, VDD=5.5V, DIO1, DIO80, CP, M, DMIN, MODE, RS/LS, DISPOFF -1 μA Output high level voltage VOH I OH=-0.4mA, DIO1, DIO80 V DD-0.4 V Output low level voltage V OL I OL=0.4mA, DIO1, DIO80 0.4 V RON(1) V DD-VEE=30V, ⎜VDE-VO⎜=0.5V VDD=4.5V, O1 to O80 *4 1.0 k Ω Driver on resistance RON(2) V DD-VEE=20V, ⎜VDE-VO⎜=0.5V VDD=4.5V, O1 to O80 *4 1.0 k Ω Consumable current drain (1) I SS V DD-VEE=30V, CP=14kHz no-load, VDD=5.5V ; VSS 100 μA Consumable current drain (2) IEE V DD-VEE=30V, CP=14kHz no-load, VDD=5.5V ; VEE 100 μA Input capacitance CI f=1MHz ; CP 8 pF Note *4 VDE = V1 or V2 or V5 or VEE, V1 = VDD, V2 = 16/17 (VDD-VEE), V5 = 1/17 (VDD-VEE) Switching Characteristics at Ta = 25±2°C, VSS = 0V, VDD = 2.7 to 5.5V Parameter Symbol Conditions min typ max unit tPLH CL=15pF ; CP → DIO1, CP → DIO80 250 ns Output delay time tPHL CL=15pF ; CP → DIO1, CP → DIO80 250 ns Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Oper ating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.

No. A2123-3/7 Package Dimensions unit:mm (typ) 3151A Pin Assignment Top view SANYO : QIP100E(14X20) 20.0 23.2 14.0 17.2 0.15 0.8 (2.7) 3.0max 0.1 0.30.65 (0.58) 13 0 80 51 100 LC79430KNE O50 O49 O48 O47 O46 O45 O44 O43 O42 O41 O40 O39 O38 O37 O36 O35 O34 O33 O32 O31 O10 O11 O12 O13 O14 O15 O16 O17 O18 O19 O20 O21 O22 O23 O24 O25 O26 O27 O28 O29 O30 1 2 3 45 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 O80 O79 O78 O77 O76 O75 O74 O73 O72 O71 O70 O69 O68 O67 O66 O65 O64 O61 O60 O59 O58 O57 O56 O55 O54 O53 O52 O51 O62 O63 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 100 81 NC DIO80 NC VEE NC DISPOFF VDD RS/LS VSS NC M MODE CP DMIN DIO1 NC NC

No. A2123-4/7 Equivalent Circuit Block Diagram

4 Level LCD Drive Circuit

(80 bits) Level Shifter (80bits) Bidirectional Shift Register (80 bits) I/O I/O O1 O2 O3 O79 O80 VDD VSS VEE M DISPOFF DIO1 CP DIO80 RS/LS MODE DMIN

No. A2123-5/7 Pin Function Pin No Symbol I/O Function

90 V DD

92 V SS

84 V EE

Supply VDD-VSS : Logic power supply VDD-VEE : LCD drive circuit power supply 87 V1 86 V2 85 V5 Supply LCD drive level power supply V1, VEE : Selected level V2, V5 : Unselected level

96 CP I Bidirectional shift register shift clock (falling edge trigger)

I I I MODE RS/LS Data Transfer Direction DIO1 DIO80 DMIN L (Shift right) O1 → O80 IN OUT * L (Single) H (Shift left) O80 → O1 OUT IN * O1 → O40 L (Shift right) O41 → O80 IN OUT IN O80 → O41 H (Dual) H (Shift left) O40 → O1 OUT IN IN * Don’t care (May be set to either “H” or “L”)

94 M I LCD drive output alternation signal

89 DISPOFF I O1 to O80 output controlling input pins. O80 O LCD drive outputs The output levels are determined by the combination of the output the data, The M signal, and the DISPOFF pin as shown in the table. M Data DISPOFF Output L L H V2 L H H V EE H L H V5 H H H V1 * * L V1 * Don’t care (May be set to either “H” or “L”) 100 NC - Must be left open.

No. A2123-6/7 R/L Seg318 Seg319 Seg320 Seg1 DIO1 DIO80 VDD VSS VEE Seg2 Seg3Com240 Com239 Com238 Com3 LCD PANEL 240×320 1/240 duty Power supply circuit Case of 1/n bias Com2 Com1LC79430KNE M RS/LS CP MODE DMIN DISPOFF DI1 to DI4 O1 to O80 O1 to O80 O1 to O80 O1 to O80O1 to O80 LC79401KNE LC79401KNE LC79401KNE M LOAD CP VEE VSS VDD CDI VEE VSS VDD CDI VEE VSS VDD CDI CDOCDOCDO R/L DISPOFF DI1 to DI4 M LOAD CP Controller FLM M LOAD GND VDD VEE R R CP DI1 to DI4 DISPOFF DISPOFF DIO1 DIO80 VDD VSS VEE LC79430KNE M RS/LS CP MODE DMIN DISPOFF R/L DISPOFF DI1 to DI4 M LOAD CP R (n-4)R R

No. A2123-7/7 Switching Characteristics Diagram PS tWC CP DIO1 (DIO80) (DMIN) DIO80 (DIO1) tR tF tSETUP tHOLD tPLH, tPHL 0.2VDD 0.8VDD ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequentia l or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s techn ical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC productsfor any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, anddistributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture oft h e part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.