LC320DXN LG | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 36
Technical content
Datasheet sections
- 1 GENERAL DESCRIPTION
- 2 ABSOLUTE MAXIMUM RATINGS
- 3 ELECTRICAL SPECIFICATIONS
- 4 OPTICAL SPECIFICATIONS
- 5 MECHANICAL CHARACTERISTICS
- 6 RELIABILITY
- 7 INTERNATIONAL STANDARDS
- 8 PACKING
- 9 PRECAUTIONS
Ver. 1.0 1 / 36 FOR APPROVAL SPECIFICATION Title 32.0” WXGA TFT LCD BUYER MODEL SUPPLIER LG Display Co., Ltd. *MODEL LC320DXN SUFFIX SER1 *When you obtain standard approval, please use the above model name without suffix Final Specification ● Preliminary Specification APPROVED BY SIGNATURE DATE Please return 1 copy for your confirmation with your signature and comments. SIGNATURE DATE J.Y.JEONG / Team Leader S.W. KWAG/ Project Leader D.S.KIM / Engineer TV Product Development Dept. LG Display Co., Ltd REVIEWED BY PREPARED BY APPROVED BY
Ver. 1.0 3 / 36 Revision No. Revision Date Page Description 0.0 Sep. 30, 2011 - Preliminary Specification (First Draft) 0.1 Nov. 07. 2011 7 LED Driver Electrical Characteristics Fixed
17 Color Coordinates Fixed
0.2 Nov. 24. 2011 22,23 Mechanical drawing update 1.0 DEC. 16. 2011 Final Specification RECORD OF REVISIONS
Ver. 1.0 4 / 36 General Features Active Screen Size 31.51 inches(800.4mm) diagonal Outline Dimension 760.0 X 450.0 X 32.5(B) (Typ.) Pixel Pitch 510.75㎛ x 510.75㎛ x R,G,B Pixel Format 1366 horiz. by 768 vert. pixels RGB stripe arrangement Color Depth 8bit(D), 16,7 M colors Luminance, White 300 cd/m2 (Center 1 point) (Typ.) Viewing Angle (CR>10) Viewing angle free ( R/L 178(Min.), U/D 178(Min.)) Power Consumption Total 42.98 Watt (Logic=4.08 W , LED Driver =38.9W @ [ExtVbr_B=100%] ) Weight 4.8kg(Typ) Display Operating Mode Transmissive mode, normally black Surface Treatment Hard coating(3H), Anti-reflection treatment of the front polarizer (Haze 1%) 1. General Description The LC320DXN is a Color Active Matrix Liquid Crystal Display with an integral Light Emitting Diode (LED) backlight system . The matrix employs a-Si Thin Film Transistor as the active element . It is a transmissive display type which is operating in the normally black mode. It has a 31.51 inch diagonally measured active display area with WXGA resolution (768 vertical by 1366 horizontal pixel array) . Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in Horizontal stripes. Gray scale or the luminance of the sub-pixel color is determined with a 8-bit gray scale signal for each dot, thus presenting a palette of more than 16.7M(6bit + A-FRC) colors. It has been designed to apply the 8-bit 1-port LVDS interface. It is intended to support LCD TV, PCTV where high brightness, super wide viewing angle, high color gamut, high color depth and fast response time are important. CN1 (30pin) Power Circuit Block Source Driver Circuit S1 S1366 Mini LVDS(RGB) TFT - LCD Panel (1366 × 768 x RGB pixels) [Gate In Panel] Timing Controller [LVDS Rx] EEPROM SDA SCL LVDS 1Port +12.0V LVDS Select #9 Back light Assembly Ext VBR-B LED Driver +24.0V, GND, On/off Control Signals Power Signals G768
Table 1. ABSOLUTE MAXIMUM RATINGS
- Ambient temperature condition (Ta = 25 2 °C )
- Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be Max 39°C, and no condensation of water.
- Gravity mura can be guaranteed below 40°C condition.
- The maximum operating temperatures is based on the test condition that the surface temperature
of display area is less than or equal to 68°C with LCD module alone in a temperature controlled chamber. improper thermal management in final product design.
Table 2. ELECTRICAL CHARACTERISTICS
- Electrical Specifications
backlight and LED Driver circuit.
- The specified current and power consumption are under the VLCD=12.0V, Ta=25 2°C, fV=60Hz
condition, and mosaic pattern(8 x 6) is displayed and fV is the frame frequency.
- The current is specified at the maximum current pattern.
- The duration of rush current is about 2ms and rising time of power input is 0.5ms (min.).
- Ripple voltage level is recommended under ± 5% of typical voltage
Table 3. ELECTRICAL CHARACTERISTICS (Continue)
- Electrical characteristics are determined after the unit has been ‘ON’ and stable for approximately 60
24Vand VBR (ExtVBR-B : 100%), it is total power consumption.
- The life time (MTTF) is determined as the time which luminance of the LED is 50% compared to that of initial
- LGD recommend that the PWM freq. is synchronized with One time harmonic of V_sync signal of system.
Though PWM frequency is over 120Hz (max 252Hz), function of LED Driver is not affected.
- The duration of rush current is about 200ms. This duration is applied to LED on time.
- Even though inrush current is over the specified value, there is no problem if I2T spec of fuse is satisfied.
- ExtVBR-B signal have to input available duty range and sequence.
After Driver ON signal is applied, ExtVBR-B should be sustained from 5% to 100% more than 500ms. For more information, please see 3-6-2. Sequence for LED Driver.
electronics and 14-pin connector is used for the integral backlight system. Table 4. MODULE CONNECTOR(CN1) PIN CONFIGURATION
5 GND Ground
6 GND Ground
7 GND Ground
8 GND Ground
9 LVDS Select ‘H’ =JEIDA , ‘L’ or NC = VESA Appendix V
10 NC No Connection 4
11 GND Ground
12 RA- LVDS Receiver Signal(-)
13 RA+ LVDS Receiver Signal(+)
14 GND Ground
15 RB- LVDS Receiver Signal(-)
16 RB+ LVDS Receiver Signal(+)
17 GND Ground
18 RC- LVDS Receiver Signal(-)
19 RC+ LVDS Receiver Signal(+)
20 GND Ground
21 RCLK- LVDS Receiver Clock Signal(-)
22 RCLK+ LVDS Receiver Clock Signal(+)
23 GND Ground
24 RD- LVDS Receiver Signal(-)
25 RD+ LVDS Receiver Signal(+)
26 GND Ground
27 NC No Connection 4
28 NC No Connection 4
29 NC No Connection 4
30 GND Ground
Notes : 1. All GND (Ground) pins should be connected together to the LCD module’s metal frame.
- All VLCD (power input) pins should be connected together.
- All Input levels of LVDS signals are based on the EIA 644 Standard.
- These pins are used only for LGD (Do not connect)
- Specific pin No. #30 is used for “No signal detection” of system signal interface.
It should be GND for NSB (No Signal Black) while the system interface signal is not. If this pin is “H”, LCD Module displays AGP (Auto Generation Pattern).
6 GND Backlight Ground
7 GND Backlight Ground
8 GND Backlight Ground
9 GND Backlight Ground
10 GND Backlight Ground
11 Status Back Light Status 2
12 VON/OFF Backlight ON/OFF control
13 NC Don’t care
14 EXTVBR-B External PWM
Table 5. LED DRIVER CONNECTOR PIN CONFIGURATION Notes : 1. GND should be connected to the LCD module’s metal frame.
- Normal : Low (under 0.7V) / Abnormal : open
- High : on duty / Low : off duty, Pin#14 can be opened. ( if Pin #14 is open , EXTVBR-B is 100% )
- Each impedance of pin #12 and 14 is over 50 [KΩ] .
Ver. 1.0 10 / 36 3-3. Signal Timing Specifications Table 6 shows the signal timing required at the input of the LVDS transmitter. All of the interface signal timings should be satisfied with the following specification for normal operation. Note: 1. The input of HSYNC & VSYNC signal does not have an effect on normal operation (DE Only Mode). If you use spread spectrum of EMI, add some additional clock to minimum value for clock margin. 2. The performance of the electro-optical characteristics may be influenced by variance of the vertical refresh rate and the horizontal frequency ※ Timing should be set based on clock frequency. Table 6-1. TIMING TABLE (DE Only Mode) ITEM Symbol Min Typ Max Unit Note Horizontal Display Period tHV - 1366 - tclk Blank tHB 90 162 410 tclk Total tHP 1456 1528 1776 tclk Vertical Display Period tVV - 768 - tHP Blank tVB (126) (180) 240 (295) tHP 1 Total tVP 788 (894) 790 (948) 1008 (1063) tHP ITEM Symbol Min Typ Max Unit Note Frequency DCLK fCLK 63.0 72.4 80.0 MHz Horizontal fH 45 47.4 55 KHz 2 Vertical fV (47) (50) (53) Hz NTSC : 57~63Hz (PAL : 47~53Hz)
Ver. 1.0 11 / 36 0.7VDD 0.3VDD DE, Data 3-4. Signal Timing Waveforms tCLK Invalid data Valid data Invalid data DE(Data Enable)
0.5 Vcc
DE(Data Enable) DCLK tHT tHV 1366 tVV tVT 1 768 768 1366 3-4-1. LVDS Input Signal Timing Diagram
Ver. 1.0 12 / 36 1) DC Specification 2) AC Specification Description Symbol Min Max Unit Note LVDS Common mode Voltage VCM 1.0 1.5 V - LVDS Input Voltage Range VIN 0.7 1.8 V - Change in common mode Voltage ΔVCM - 250 mV - LVDS 1’st Clock Tclk LVDS 2nd / 3rd / 4th Clock tSKEW_min tSKEW_max 20% 80% A tRF LVDS Data tSKEW LVDS Clock T clk ( F clk = 1 / T clk ) tSKEW A 1. All Input levels of LVDS signals are based on the EIA 644 Standard. 2. If tRF isn’t enough, teff should be meet the range. 3. LVDS Differential Voltage is defined within teff Description Symbol Min Max Unit Note LVDS Differential Voltage VTH 100 300 mV VTL -300 -100 mV LVDS Clock to Data Skew tSKEW - |(0.20*Tclk)/7| ps - LVDS Clock/DATA Rising/Falling time tRF 260 |(0.3*Tclk)/7| ps 2 Effective time of LVDS teff |± 360| - ps - LVDS Clock to Clock Skew (Even to Odd) tSKEW_EO - |1/7* Tclk| ps - LVDS + LVDS - 0 V V CM # V CM = { ( LVDS +) + ( LVDS - ) } / 2 V IN _ MAX V IN _ MIN High Threshold Low Threshold Note 3-4-2. LVDS Input Signal Characteristics
Ver. 1.0 13 / 36 data data Vcm tui 0.5tui 360ps 360ps tui : Unit Interval teff clk clk Vcm VTH VTL
The brightness of each primary color (Red, Green, Blue) is based on the 8-bit gray scale data input for the color. The higher binary input, the brighter the color. Table 7 provides a reference for color versus data input. Table 7. COLOR DATA REFERENCE
Table 8. POWER SEQUENCE
- Even though T1 is over the specified value, there is no problem if I2T spec of fuse is satisfied.
- If T2 is satisfied with specification after removing LVDS Cable, there is no problem.
- The T3 / T4 is recommended value, the case when failed to meet a minimum specification,
abnormal display would be shown. There is no reliability problem.
- T5 should be measured after the Module has been fully discharged between power off and on period.
- If the on time of signals (Interface signal and user control signals) precedes the on time of Power (VLCD),
it will be happened abnormal display. When T6 is NC status, T6 doesn’t need to be measured.
- If there is no abnormal display, no problem.
- It is recommendation specification that T8 has to be 100ms as a minimum value.
※ Please avoid floating state of interface signal at invalid period. ※ When the power supply for LCD (VLCD) is off, be sure to pull down the valid and invalid data to 0V.
Table 9. Power Sequence for LED Driver Notes : 1. T1 describes rising time of 0V to 24V and this parameter does not applied at restarting time. Even though T1 is over the specified value, there is no problem if I2T spec of fuse is satisfied.
- In T6 section, ExtVBR-B should be sustained from 5% to 100% .
Table 10. OPTICAL CHARACTERISTICS Optical characteristics are determined after the unit has been ‘ON’ and stable in a dark environment at 25± 2°C. The values are specified at distance 50cm from the LCD surface at a viewing angle of and equal to 0 °. FIG. 1 shows additional information concerning the measurement equipment and method.
Table 11. GRAY SCALE SPECIFICATION It is measured at center 1-point.
- Surface luminance are determined after the unit has been ‘ON’ and 1 Hour after lighting the
1-point across the LCD surface 50cm from the surface with all pixels displaying white. Where Lon1 to Lon5 are the luminance with all pixels displaying white at 5 locations . For more information, see the FIG. 2.
- Response time is the time required for the display to transit from any gray to white (Rise Time, TrR)
and from any gray to black (Decay time, TrD). For additional information see the FIG. 3. ※ G to GBW Spec stands for average value of all measured points.
- G to G σ is Variation of Gray to Gray response time composing a picture
- Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are
is normal to the LCD module surface. For more information, see the FIG. 4. Gamma Value is approximately 2.2. For more information, see the Table 11.
Ver. 1.0 19 / 36 Measuring point for surface luminance & measuring point for luminance variation. FIG. 2 5 Points for Luminance Measure H A V B ③ ② ⑤ ④ A : H / 4 mm B : V / 4 mm @ H,V : Active Area FIG. 3 Response Time Response time is defined as the following figure and shall be measured by switching the input signal for “Gray(N)” and “Black or White”. White Gray(N) Tr Tf 100 Optical Response N = 0(Black)~255(White) Gray(N) Black
Ver. 1.0 20 / 36 FIG. 4 Viewing Angle Dimension of viewing angle range Normal Y E = 0, Right = 180, Lef t = 270, Down = 90, Up
Table 12 provides general mechanical characteristics.
- Mechanical Characteristics
Table 12. MECHANICAL CHARACTERISTICS Note : 1.Please refer to a mechanical drawing in terms of tolerance at the next page.
Ver. 1.0 22 / 36 <FRONT VIEW>
Ver. 1.0 23 / 36 <REAR VIEW> <REAR VIEW>
Table 13. ENVIRONMENT TEST CONDITION Note : Before and after Reliability test, LCM should be operated with normal function.
1 High temperature storage test Ta= 60°C, 240h
2 Low temperature storage test Ta= -20°C, 240h
3 High temperature operation test Ta= 50°C, 50%RH, 240h
4 Low temperature operation test Ta= 0°C, 240h
5 Vibration test
6 Shock test
7 Humidity condition Operation Ta= 40 °C, 90%RH
8 Altitude operating
Ver. 1.0 25 / 36 7. International Standards 7-1. Safety 7-3. Environment a) RoHS, Directive 2002/95/EC of the European Parliament and of the council of 27 January 2003 7-2. EMC a) ANSI C63.4 “American National Standard for Methods of Measurement of Radio -Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz.” American National Standards Institute (ANSI), 2003. b) CISPR 22 “Information technology equipment – Radio disturbance characteristics – Limit and methods of measurement." International Special Committee on Radio Interference (CISPR), 2005. c) CISPR 13 “Sound and television broadcast receivers and associated equipment – Radio disturbance characteristics – Limits and method of measurement." International Special Committee on Radio Interference (CISPR), 2006. a) UL 60065, Underwriters Laboratories Inc. Audio, Video and Similar Electronic Apparatus - Safety Requirements. b) CAN/CSA C22.2 No.60065:03, Canadian Standards Association. Audio, Video and Similar Electronic Apparatus - Safety Requirements. c) EN 60065, European Committee for Electrotechnical Standardization (CENELEC). Audio, Video and Similar Electronic Apparatus - Safety Requirements. Class 1M LED Product IEC60825-1 : 2001 Embedded LED Power (Class1M) Notes 1. Laser (LED Backlight) Information 2. Caution : LED inside. Class 1M laser (LEDs) radiation when open. Do not open while operating. d) IEC 60065, The International Electrotechnical Commission (IEC). Audio, Video and Similar Electronic Apparatus - Safety Requirements. (Including report of IEC60825-1:2001 clause 8 and clause 9)
Ver. 1.0 26 / 36 Note 1. YEAR 2. MONTH B Nov Mark Month A Oct Jun Jul Aug Sep Apr May C 3 2 1 Dec Mar Feb Jan b) Location of Lot Mark Serial No. is printed on the label. The label is attached to the backside of the LCD module. This is subject to change without prior notice. 8. Packing 8-2. Packing Form 8-1. Information of LCM Label a) Lot Mark A B C D E F G H I J K L M A,B,C : SIZE(INCH) D : YEAR E : MONTH F ~ M : SERIAL NO. a) Package quantity in one Pallet : 30 pcs b) Pallet Size : 1140 mm X 870 mm X 1161 mm. Mark Year K 2020 F 2016 G 2017 H 2018 J 2019 D 2014 E 2015 C B A 2013 2012 2011
Ver. 1.0 27 / 36 Please pay attention to the followings when you use this TFT LCD module. 9-1. Mounting Precautions (1)You must mount a module using specified mounting holes (Details refer to the drawings) . (2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the module. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module. (3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer. Transparent protective plate should have sufficient strength in order to the resist external force. (4) You should adopt radiation structure to satisfy the temperature specification. (5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break by electro-chemical reaction. (6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB pencil lead. And please do not rub with dust clothes with chemical treatment. Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental to the polarizer.) (7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like chamois soaks with petroleum benzine. Normal-hexane is recommended for cleaning the adhesives used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. * There is no problem of Panel crack under 5kgf / φ10mm (8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes deformations and color fading. (9) Do not open the case because inside circuits do not have sufficient strength. 9-2. Operating Precautions (1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage : V=± 200mV(Over and under shoot voltage) (2) Response time depends on the temperature.(In lower temperature, it becomes longer.) (3) Brightness depends on the temperature. (In lower temperature, it becomes lower.) And in lower temperature, response time(required time that brightness is stable after turned on) becomes longer. (4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur. (5) When fixed patterns are displayed for a long time, remnant image is likely to occur. (6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be done by system manufacturers. Grounding and shielding methods may be important to minimized the interference. (7) Please do not give any mechanical and/or acoustical impact to LCM. Otherwise, LCM can’t be operated its full characteristics perfectly. (8) A screw which is fastened up the steels should be a machine screw. (if not, it causes metallic foreign material and deal LCM a fatal blow) (9) Please do not set LCD on its edge. (10) The conductive material and signal cables are kept away from LED driver inductor to prevent abnormal display, sound noise and temperature rising. 9. Precautions
Ver. 1.0 28 / 36 Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly. 9-3. Electrostatic Discharge Control Strong light exposure causes degradation of polarizer and color filter. 9-4. Precautions for Strong Light Exposure When storing modules as spares for a long time, the following precautions are necessary. (1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature between 5°C and 35°C at normal humidity. (2) The polarizer surface should not come in contact with any other object. It is recommended that they be stored in the container in which they were shipped. (3) Storage condition is guaranteed under packing conditions. (4) The phase transition of Liquid Crystal in the condition of the low or high storage temperature will be recovered when the LCD module returns to the normal condition 9-5. Storage 9-6. Handling Precautions for Protection Film (1) The protection film is attached to the bezel with a small masking tape. When the protection film is peeled off, static electricity is generated between the film and polarizer. This should be peeled off slowly and carefully by people who are electrically grounded and with well ion- blown equipment or in such a condition, etc. (2) When the module with protection film attached is stored for a long time, sometimes there remains a very small amount of glue still on the bezel after the protection film is peeled off. (3) You can remove the glue easily. When the glue remains on the bezel surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal- hexane.
Ver. 1.0 29 / 36 # APPENDIX- I ■ Pallet Ass’y NO. DESCRIPTION MATERIAL
1 PACKING ASS’Y
2 PALLET Plywood
3 BAND PP
4 CLIP, BAND STEEL
5 Angle Cover PAPER
6 WRAP LDPE
7 LABEL ART 100X70
Ver. 1.0 30 / 36 ■ Packing Ass’y NO. DESCRIPTION MATERIAL
1 LCD Module
2 BAG AL
3 TAPE MASKING 20MMX50M
4 Packing,Bottom EPS
5 Packing,Top EPS
6 BOX PAPER_DW3
7 TAPE OPP 70MMX300M
8 Label ART 100X70
Ver. 1.0 31 / 36 # APPENDIX- II-1 ■ LCM Label Model UL, TUV Mark LGD Logo Origin LC320DXN (SE)(R1) X X X X X X X X X X X X X X X X X MADE IN KOREA RoHS Verified Serial No.
Ver. 1.0 32 / 36 # APPENDIX- II-2 ■ Box Label LC320DXN SER1
5 PCS 001/01-01
MADE IN KOREA RoHS Verified XXXXXXXXXXXXX XXX ■ Pallet Label LC320DXN SER1
30 PCS 001/01-01
MADE IN KOREA RoHS Verified XXXXXXXXXXXXX XXX
Ver. 1.0 33 / 36 # APPENDIX-III-1 ■ Required signal assignment for Flat Link Transmitter(Pin9=“L” or NC) RED0 RED1 RED2 RED3 RED4 RED5 RED6 RED7 GREEN0 GREEN1 GREEN2 GREEN3 GREEN4 GREEN5 GREEN6 GREEN7 BLUE0 BLUE1 BLUE2 BLUE3 BLUE4 BLUE5 BLUE6 BLUE7 Hsync Vsync Data Enable CLOCK Host System
24 Bit
100Ω 100Ω 100Ω 100Ω 100Ω KDF71G-30S-1H Timing Controller LCD Module GND Notes: 1. The LCD module uses a 100 Ohm(Ω) resistor between positive and negative lines of each receiver input. 2. Refer to LVDS transmitter data sheet for detail descriptions. (DS90C385 or Compatible) 3. ‘7’ means MSB and ‘0’ means LSB at R,G,B pixel data.
Ver. 1.0 34 / 36 # APPENDIX-III-2 ■ Required signal assignment for Flat Link Transmitter(Pin9=“H”) RED0 RED1 RED2 RED3 RED4 RED5 RED6 RED7 GREEN0 GREEN1 GREEN2 GREEN3 GREEN4 GREEN5 GREEN6 GREEN7 BLUE0 BLUE1 BLUE2 BLUE3 BLUE4 BLUE5 BLUE6 BLUE7 Hsync Vsync Data Enable CLOCK Host System 100Ω 100Ω 100Ω 100Ω 100Ω LCD Module Vcc KDF71G-30S-1H Timing Controller Notes: 1. The LCD module uses a 100 Ohm(Ω) resistor between positive and negative lines of each receiver input. 2. Refer to LVDS transmitter data sheet for detail descriptions. (DS90C385 or Compatible) 3. ‘7’ means MSB and ‘0’ means LSB at R,G,B pixel data.
Ver. 1.0 35 / 36 ■ LVDS Select : “H” Data-Mapping (JEIDA format) ■ LVDS Select : “L” Data-Mapping (VESA format) R17 R16 R15 R14 G12 R13 R12’ R12 R13’ G12” B12 G17 G16 G15 B13 G14 G13’ G13 G14’ B13” VSYNC HSYNC B17 B16 DE B15 B14’ B14 B15’ DE” B11 B10 G11 G10 X R11 R10’ R10 R11’ X” RCLKP RCLKM RAP RBP RCP RDP R15 R14 R13 R12 G10 R11 R10’ R10 R11’ G10” B10 G15 G14 G13 B11 G12 G11’ G11 G12’ B15” VSYNC HSYNC B15 B14 DE B13 B12’ B12 B13’ DE” B17 B16 G17 G16 X R17 R16’ R16 R17’ X” RCLKP RCLKM RAP RBP RCP RDP LVDS Data-Mapping info. (8bit) # APPENDIX- IV
Ver. 1.0 36 / 36 # APPENDIX- V Circuit Block Diagram of LVDS Format Selection pin ASIC (TCON) System Side LCM Side LVDS Select (Pin 9) Selector 1KΩ Option Pin Circuit Block Diagram 50KΩ