LBEE5XV2BZ-883

SP-XV2BZ-A MURATA | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 57

Technical content

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. W-LAN+Bluetooth Combo Module Data Sheet Infineon Chipset CYW54590 for 802.11a/b/g/n/ac 2x2 MIMO + Bluetooth 5.2 MP P/N : LBEE5XV2BZ-883 Sample P/N : LBEE5XV2BZ-SMP

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd.

Revision History

Code Date Description Comments - Dec. 15, 2021 First Issue A Jun. 15, 2022 Title Page 4 Page 5 Page 8 Page 50 Adding MP part number Block Diagram Adding specification temperature Revising typo in pin description Revising regulatory certification

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Table of Contents Please be aware that an important notice concerning availability, standard warranty and use in critical applications of Murata products and disclaimers thereto appears at the end of this specification sheet.

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 1. SCOPE This specification is applied to the IEEE802.11a/b/g/n/ac W-LAN 2x2 MIMO + Bluetooth 5.2 combo module. 2. KEY FEATURE - Infineon CYW54590 inside - Compliant with IEEE802.11a/b/g/n/ac, 5G MIMO - Compliant with Bluetooth specification v5.2 - Supports standard SDIO Interface for WLAN - Interface support for Bluetooth is Host Controller Interface (HCI) - Surface mount type 11.4 x 8.9 mm (Typical), H = 1.4 mm(Max.) - Weight: 0.36g - MSL: 3 - RoHS compliant 3. BLOCK DIAGRAM 4. SAMPLE ORDERING INFORMATION Ordering Part Number Description LBEE5XV2BZ-883 MP Part Number LBEE5XV2BZ-SMP In case of sample order LBEE5XV2BZ-EVK Evaluation Kit Type2BZ VDDIO VBAT Ref Clock (32MHz) BPF DIPLEX CYW54590 5GHz Tx Chain 1 5GHz Rx Chain 1 2.4GHz Tx Chain 1 2.4GHz Rx Chain 1 5GHz Tx Chain 0 5GHz Rx Chain 0 2.4GHz Tx Chain 0 2.4GHz Rx Chain 0 Bluetooth Tx/Rx DIPLEX BPF ANT1 ANT0 UART for BT ANT2(Optional) SDIO for WLAN

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 5. ABSOLUTE MAXIMUM RATINGS Parameter Min Max Unit Storage Temperature -40 +85 deg.C Supply Voltage VBAT -0.5 +6.0 V VDDIO -0.5 +3.9 V Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. No damage assuming only one parameter is set at limit at a time with all other parameters is set within operating condition. 6. OPERATING CONDITION Parameter Min Typ max Unit Operating Temperature -40 25 85 deg.C Specification Temperature -10 25 70 deg.C Operating Voltage VBAT 3.0 3.3 4.8 V VDDIO 1.62 1.8 or 3.3 3.63 V Note) Min. voltage of VBAT is sensitive to get RF performance, so please keep min. voltages level at the input of these module terminals, otherwise RF performance significantly goes worse. 7. EXTERNAL LPO_IN SIGNAL REQUIREMENT Parameter External LPO_IN Clock Unit Nominal input frequency 32.768 kHz Frequency accuracy +/-250 ppm Duty cycle 30-70 % Input signal amplitude 200 - 3300 mV, p-p Signal type Square-wave or sine-wave - Input impedance1 > 100k ohm < 5 pF Clock jitter (during initial start-up) <10,000 ppm 1 When power is applied or switch off.

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 8. DIMENSIONS, MARKING AND TERMINAL CONFIGURATIONS Marking Meaning A Module Part Number B Inspection Number C Serial Number D Pin 1 Marking E 2D code F Murata Logo Mark Dimensions Mark Dimensions Mark Dimensions Mark Dimensions m1 0.8 ± 0.1 m2 0.8 ± 0.1 (unit : mm) <Top View> <Side View> b1 a1 e1 c1 e2 b2 c2 e4 m1 e7 e6 e5 c4 e10 <Bottom View> T L W LBEE5XV2BZ SSXXXXXXX A D E C B 123456789 F e11 e12 1 pin mark (φ0.5±0.1 mm)

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 9. MODULE PIN DESCRIPTIONS <TOP VIEW> No. Terminal Name No. Terminal Name No. Terminal Name

1 GND 31 RF_SW_CTRL11 61 SDIO_DATA_3

2 GPIO_17 32 GND 62 SDIO_DATA_2

3 GPIO_18 33 ANT_1 63 SDIO_DATA_1

4 GPIO_19 34 GND 64 GND

5 WL_REG_ON 35 GND 65 VBAT

6 BT_REG_ON 36 BT_UART_RTS_N 66 VBAT

7 GND 37 BT_UART_CTS_N 67-73 GND

8 VDDIO 38 BT_UART_RXD 74 BT_PCM_IN

9 GND 39 BT_UART_TXD 75 BT_PCM_OUT

10 GND 40 GPIO_5 76 BT_PCM_CLK

11 GND 41 GPIO_4 77 BT_PCM_SYNC

12 BT_OUT 42 GPIO_7 78 GND

13 GND 43 GPIO_6 79 RF_SW_CTRL4

14 BT_IN 44 NC 80 GND

15 GND 45 NC 81 RF_SW_CTRL12

16 RF_SW_CTRL5 46 NC 82 BT_GPIO_5

17 GND 47 GND 83 BT_GPIO_4

18 GND 48 NC 84 BT_GPIO_2

19 ANT_0 49 NC 85 BT_GPIO_3

20 GND 50 GND 86 GPIO_3

21 GND 51 NC 87 JTAG_SEL

22 BT_HOST_WAKE 52 NC 88 GPIO_2

23 BT_DEV_WAKE 53 GND 89 GPIO_1

24 CLK_REQ 54 NC 90 GPIO_0

25 LPO_IN 55 NC 91 GPIO_8

26 BT_I2S_DO 56 GND 92 GPIO_9

27 BT_I2S_DI 57 VDDIO 93 GPIO_10

28 BT_I2S_CLK 58 SDIO_CMD 94 GPIO_11

29 BT_I2S_WS 59 SDIO_CLK 95-104 GND

30 GND 60 SDIO_DATA_0

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. No. Pin name Type Connection to IC pin name Description

1 GND - - Ground

2 GPIO_17 I/O GPIO_17 Programmable GPIO Pin

3 GPIO_18 I/O GPIO_18 Programmable GPIO Pin

4 GPIO_19 I/O GPIO_19 Programmable GPIO Pin

5 WL_REG_ON I WL_REG_ON

Used by PMU to power up or power down the internal CYW54590 regulators used by the WLAN section. Also, when deasserted, this pin holds the WLAN section in reset. This pin has an internal 200k ohm pull-down resistor that is enabled by default. It can be disabled through programming.

6 BT_REG_ON I BT_REG_ON

Used by PMU to power up or power down the internal CYW54590 regulators used by the Bluetooth section. Also, when deasserted, this pin holds the Bluetooth section in reset. This pin has an internal 200k ohm pull-down resistor that is enabled by default. It can be disabled through programming.

7 GND - - Ground

8 VDDIO I

SYS_VDDIO WCC_VDDIO BT_VDDO VDDIO IO supply

9 GND - - Ground

10 GND - - Ground

11 GND - - Ground

12 BT_OUT

13 GND - - Ground

14 BT_IN

15 GND - - Ground

16 RF_SW_CTRL5 O O

Programmable RF switch control lines. The control lines are programmable via the driver and NVRAM file.

17 GND - - Ground

18 GND - - Ground

19 ANT_0 - - RF Port for WLAN (2.4GHz & 5GHz) and BT

20 GND - - Ground

21 GND - - Ground

22 BT_HOST_WAKE O BT_HOST_WAKE

Host wake-up: Signal from the module to the host indicating that the module requires attention.

23 BT_DEV_WAKE I BT_DEV_WAKE

Bluetooth device wake-up: Signal from the host to the module indicating that the host requires attention.

24 CLK_REQ I/O CLK_REQ Reference clock request (shared by BT and

WLAN). If not used, this can be no-connect. 25 LPO_IN I LPO_IN External sleep clock input (32.768 kHz)

26 BT_I2S_DO I/O BT_I2S_DO I 2S data output

27 BT_I2S_DI I/O BT_I2S_DI I 2S data input

28 BT_I2S_CLK I/O BT_I2S_CLK I2S clock, can be master (output) or slave

(input). 29 BT_I2S_WS I/O BT_I2S_WS I 2S WS, can be master (output) or slave (input).

30 GND - - Ground

31 RF_SW_CTRL11 O RF_SW_CTRL11

Programmable RF switch control lines. The control lines are programmable via the driver and NVRAM file.

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd.

32 GND - - Ground

33 ANT_1 RF Port for WLAN (2.4GHz & 5GHz)

34 GND - - Ground

35 GND - - Ground

36 BT_UART_RTS_N O BT_UART_RTS_N

UART request-to-send. Active-low request-to- send signal for the HCI UART interface. BT LED control pin. 37 BT_UART_CTS_N I BT_UART_CTS_N UART clear-to-send. Active-low clear-to-send signal for the HCI UART interface. 38 BT_UART_RXD I BT_UART_RXD UART serial input. Serial data input for the HCI UART interface. 39 BT_UART_TXD O BT_UART_TXD UART serial output. Serial data output for the HCI UART interface.

40 GPIO_5 GPIO_5

Programmable GPIO pins. 41 GPIO_4 GPIO_4

42 GPIO_7 GPIO_7

43 GPIO_6 GPIO_6

44 NC - - No Connect

45 NC - - No Connect

46 NC - - No Connect

47 GND - - Ground

48 NC - - No Connect

49 NC - - No Connect

50 GND - - Ground

51 NC - - No Connect

52 NC - - No Connect

53 GND - - Ground

54 NC - - No Connect

55 NC - - No Connect

56 GND - - Ground

57 VDDIO_SD PWR VDDIO_SD 1.8V–3.3V supply for SDIO pads. 58 SDIO_CMD I/O SDIO_CMD SDIO command line. 59 SDIO_CLK I SDIO_CLK SDIO clock input. 60 SDIO_DATA_0 I/O SDIO_DATA_0 SDIO data line 0. 61 SDIO_DATA_3 I/O SDIO_DATA_3 SDIO data line 3. 62 SDIO_DATA_2 I/O SDIO_DATA_2 SDIO data line 2. 63 SDIO_DATA_1 I/O SDIO_DATA_1 SDIO data line 1.

64 GND - - Ground

65 VBAT PWR SR_VDDBAT5V

LDO_VDDBAT5V VBAT supply 66 67-

73 GND - - Ground

74 BT_PCM_IN I BT_PCM_IN PCM data input. 75 BT_PCM_OUT O BT_PCM_OUT PCM data output.

76 BT_PCM_CLK I/O BT_PCM_CLK PCM clock; can be master (output) or slave

(input).

77 BT_PCM_SYNC I/O BT_PCM_SYNC PCM sync; can be master (output) or slave

(input).

78 GND - - Ground

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd.

79 RF_SW_CTRL4 O RF_SW_CTRL4

Programmable RF switch control lines. The control lines are programmable via the driver and NVRAM file.

80 GND - - Ground

81 RF_SW_CTRL12 O RF_SW_CTRL12

Programmable RF switch control lines. The control lines are programmable via the driver and NVRAM file.

82 BT_GPIO_5 I/O BT_GPIO_5

Bluetooth general-purpose I/O. 83 BT_GPIO_4 I/O BT_GPIO_4

84 BT_GPIO_2 I/O BT_GPIO_2

85 BT_GPIO_3 I/O BT_GPIO_3

86 GPIO_3 I/O GPIO_3 Programmable GPIO pins.

87 JTAG_SEL I/O JTAG_SEL

JTAG select: pull high to select the JTAG interface. If the JTAG interface is not used this pin may be left floating or connected to ground.

88 GPIO_2 I/O GPIO_2

Programmable GPIO pins.

89 GPIO_1 I/O GPIO_1

90 GPIO_0 I/O GPIO_0

91 GPIO_8 I/O GPIO_8

92 GPIO_9 I/O GPIO_9

93 GPIO_10 I/O GPIO_10

94 GPIO_11 I/O GPIO_11

104 GND - - Ground

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 10. REFERENCE PERIPHERAL CIRCUIT

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 11. I/O States The following notations are used in I/O State Table.  I: Input signal  O: Output signal  I/O: Input/Output signal  PU = Pulled up  PD = Pulled down  NoPull = Neither pulled up nor pulled down  Where applicable, the default value is shown in bold brackets (for example, [default value]) I/O State Table Name I/O Keeper Active Mode Low Power State/Sleep (All Power Present) Power-down (BT_REG_ON and WL_REG_ON Held Low) Out-of-Reset; Before SW Download (BT_REG_ON High; WL_REG_ON High) Power-down (WL_REG_ON High and BT_REG_ON=0) and VDDIOs Are Present Power Rail WL_REG_ON BT_REG_ON I N I: PD Pull-down can be disabled I: PD Pull-down can be disabled I: PD (of 200K) I: PD (of 200K) I: PD (of 200K) – GPIO_0 I/O Y I/O: PU, PD, NoPull Programmable [PD] I/O: PU, PD, NoPull Programmable [PD] High-Z, NoPull I: PD I: PD VDDIO GPIO_1 I/O Y I/O: PU, PD, NoPull Programmable [NoPull] I/O: PU, PD, NoPull Programmable [NoPull] High-Z, NoPull I: NoPull I: NoPull VDDIO GPIO_2 I/O Y I/O: PU, PD, NoPull Programmable [NoPull] I/O: PU, PD, NoPull Programmable [NoPull] High-Z, NoPull I: NoPullb I: NoPull VDDIO GPIO_3 I/O Y I/O: PU, PD, NoPull Programmable [NoPull] I/O: PU, PD, NoPull Programmable [NoPull] High-Z, NoPull I: NoPullb I: NoPull VDDIO GPIO_4 I/O Y I/O: PU, PD, NoPull Programmable [NoPull] I/O: PU, PD, NoPull Programmable [NoPull] High-Z, NoPull I: NoPullb I: NoPull VDDIO GPIO_5 I/O Y I/O: PU, PD, NoPull Programmable [NoPull] I/O: PU, PD, NoPull Programmable [NoPull] High-Z, NoPull I: NoPullb I: NoPull VDDIO GPIO_6 I/O Y I/O: PU, PD, NoPull Programmable [NoPull] I/O: PU, PD, NoPull Programmable [NoPull] High-Z, NoPull I: NoPullb I: NoPull VDDIO GPIO_7 I/O Y I/O: PU, PD, NoPull Programmable [NoPull] I/O: PU, PD, NoPull Programmable [NoPull] High-Z, NoPull I: NoPull I: NoPull VDDIO GPIO_8 I/O Y I/O: PU, PD, NoPull Programmable [NoPull] I/O: PU, PD, NoPull Programmable [NoPull] High-Z, NoPull I: NoPull I: NoPull VDDIO GPIO_9 I/O Y I/O: PU, PD, NoPull Programmable [PU] I/O: PU, PD, NoPull Programmable [NoPull] I: PU I: PU I:PU VDDIO

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. GPIO_10 I/O Y I/O: PU, PD, NoPull Programmable [NoPull] I/O: PU, PD, NoPull Programmable [NoPull] High-Z, NoPull I: NoPull I: NoPull VDDIO GPIO_11 I/O Y I/O: PU, PD, NoPull Programmable [PU] I/O: PU, PD, NoPull Programmable [PU] I: PU I: PU I:PU VDDIO GPIO_17 I/O Y I/O: PU, PD, NoPull Programmable [NoPull] I/O: PU, PD, NoPull Programmable [NoPull] High-Z, NoPull I: NoPull I: NoPull VDDIO GPIO_18 I/O Y I/O: PU, PD, NoPull Programmable [NoPull] I/O: PU, PD, NoPull Programmable [NoPull] High-Z, NoPull I: NoPull I: NoPull VDDIO GPIO_19 I/O Y I/O: PU, PD, NoPull Programmable [NoPull] I/O: PU, PD, NoPull Programmable [NoPull] High-Z, NoPull I: NoPull I: NoPull VDDIO RF_SW_CTRL_X O N O: NoPull O: NoPull High-Z, NoPull O: NoPull O: NoPull VDDIO_RF CLK_REQ O Y Open drain or push-pull (programmable).Active high. Open drain or push-pull (programmable).Active high. High-Z, NoPull Open drain. Active high Open drain. Active high BT_VDDO BT_HOST_WAKE O Y Input/Output; PU, PD, NoPull (programmable) Input/Output; PU, PD, NoPull (programmable) High-Z, NoPull Input, PU Input, PD BT_VDDO BT_DEV_WAKE I Y Input/Output; PU, PD, NoPull (programmable) Input/Output; PU, PD, NoPull (programmable) High-Z, NoPull Input, PD Input, PD BT_VDDO BT_GPIO_2 BT_GPIO_3 I/O Y Input/Output; PU, PD, NoPull (programmable) Input/Output; PU, PD, NoPull (programmable) High-Z, NoPull Input, PD Input, PD BT_VDDO BT_GPIO_4 BT_GPIO_5 I/O Y Input/Output; PU, PD, NoPull (programmable) Input/Output; PU, PD, NoPull (programmable) High-Z, NoPull Input, PU Input, PU BT_VDDO BT_UART_CTS_N I Y Input, NoPull Input, NoPull High-Z, NoPull Input, PU Input, PU BT_VDDO BT_UART_RTS_N O Y Output, NoPull Output, NoPull High-Z, NoPull Input, PU Input, PU BT_VDDO BT_UART_RXD I Y Input, NoPull Input, NoPull High-Z, NoPull Input, PU Input, PU BT_VDDO BT_UART_TXD O Y Output, NoPull Output, NoPull High-Z, NoPull Input, PU Input, PU BT_VDDO BT_PCM_CLK I/O Y Input, NoPull Input, NoPull High-Z, NoPull Input, PD Input, PD BT_VDDO BT_PCM_IN I/O Y Input, NoPull Input, NoPull High-Z, NoPull Input, PD Input, PD BT_VDDO BT_PCM_OUT I/O Y Input, NoPull Input, NoPull High-Z, NoPull Input, PD Input, PD BT_VDDO BT_PCM_SYNC I/O Y Input, NoPull Input, NoPull High-Z, NoPull Input, PD Input, PD BT_VDDO BT_I2S_CLK I/O Y Input, NoPull Input, NoPull High-Z, NoPull High-Z, NoPull High-Z, NoPull BT_VDDO BT_I2S_DO I/O Y Output, NoPull Output, NoPull High-Z, NoPull Input, PD Input, PD BT_VDDO BT_I2S_DI I/O Y Input, NoPull Input, NoPull High-Z, NoPull Input, PD Input, PD BT_VDDO BT_I2S_WS I/O Y Input, NoPull Input, NoPull High-Z, NoPull High-Z, NoPull High-Z, NoPull BT_VDDO

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 12. POWER SEQUENCE 12.1. POWER ON SEQUENCE - VBAT and VDDIO should not rise 10%-90% faster than 40 microseconds. - VBAT should be up before or at the same time as VDDIO. VDDIO should NOT be present fast or be held high before VBAT is high. - WL_REG_ON and BT_REG_ON should be up after sleep clock oscillation is stabilized. - Please proceed reset by WL_REG_ON and BT_REG_ON until it starts normally if it doesn’t wake from sleep property or it is presented with uncertain status. - Please keep repeats power off sequence and power on sequence several times until it started normally. - The CYW54590 has an internal Power-on reset (POR) circuit. The device will be held in reset for a maximum of 110 ms after internal regulators and VDDIO have passed the POR threshold. Wait at least 150 ms after WL_REG_ON is driven high before initiating SDIO accesses. 12.1.1. Power On Sequence for WLAN = ON and BT = ON 12.1.2. Power On Sequence for WLAN = OFF and BT = OFF 32.768kHz Sleep Clock VBAT VDDIO WL_REG_ON BT_REG_ON 90% of VH ~ 2 Sleep cycle 32.768kHz Sleep Clock VBAT VDDIO WL_REG_ON BT_REG_ON

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 12.1.3. Power On Sequence for WLAN = ON and BT = OFF 12.1.4. Power On Sequence for WLAN = OFF and BT = ON 32.768kHz Sleep Clock VBAT VDDIO WL_REG_ON BT_REG_ON 90% of VH ~ 2 Sleep cycle 32.768kHz Sleep Clock VBAT VDDIO WL_REG_ON BT_REG_ON 90% of VH ~ 2 Sleep cycle

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 12.1.5. Power Off Sequence - VDDIO should be down before or at the same time as VBAT. VBAT should NOT be down earlier than VDDIO low. VDDIO becomes low state is prior to VBAT low. - VBAT and VDDIO should be down after WL_REG_ON and BT_REG_ON are low. Waiting time from REG_ON down to power supply off is not prescribed. 12.1.6. Power Off Sequence for WLAN = ON and BT = ON 12.1.7. Power Off Sequence for WLAN = OFF and BT = OFF 32.768kHz Sleep Clock VBAT VDDIO WL_REG_ON BT_REG_ON After settled VIL 32.768kHz Sleep Clock VBAT VDDIO WL_REG_ON BT_REG_ON

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 12.1.8. Power Off Sequence for WLAN = ON and BT = OFF 12.1.9. Power Off Sequence for WLAN = OFF and BT = ON 32.768kHz Sleep Clock VBAT VDDIO WL_REG_ON BT_REG_ON After settled VIL 32.768kHz Sleep Clock VBAT VDDIO WL_REG_ON BT_REG_ON After settled VIL

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 13. INTERFACE TIMING AND AC CHARACTERISTICS 13.1. Bluetooth UART Timing Reference Description Min Typ Max Unit 1 Delay time, UART_CTS_N low to UART_TXD valid - - 1.5 Bit periods

2 Setup time, UART_CTS_N high before midpoint of

stop bit - - 0.5 Bit periods

3 Delay time, midpoint of stop bit to UART_RTS_N

high - - 0.5 Bit periods BT_UART_CTS_NBT_UART_TXDUART_RXDUART_RTS_N132Midpoint of STOP bitMidpoint of STOP bit

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 13.2. Bluetooth Startup Signaling Sequence Reference Description Min Typ Max Unit T3 Time for the BT device to settle its IOs after BT_REG_ON is asserted. - - 40.0 ms T4 Time for the BT device to drive UART_RTS_N low after the host drives UART_CTS_N low - - 10.0 ms BT_GPIO_1 BT_UART_CTS_N BT_UART_RTS_N Sleep Clock BT_GPIO_0 BT_REG_ON (BT_DEV_WAKE) (BT_HOST_WAKE) BT Device IOs unconfigured BT Device IOs configured Pulled Driven Host drives this low. Indicates completion of initialization

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 13.3. Bluetooth PCM Interface Timing Data Formatting The IC used in the module may be configured to generate and accept several different data formats. For conventional narrowband speech mode, the IC uses 13 of the 16 bits in each PCM frame. The location and order of these 13 bits can be configured to support various data formats on PCM interface. The remaining three bits are ignored on the input and may be filled with 0s, 1s, a sigh bit, or a programmed value on the output. The default format is 13bit 2’s complement data, left justified, and clocked MSB first. Wideband Speech Support When the host encodes wideband speech (WBS) packets in transparent mode, the encoded packets are transferred over the PCM bus for an eSCO voice connection. In this mode, the PCM bus is typically configured in master mode for a 4kHz sync rate with 16-bit samples, resulting in a 64 kbps bit rate. The IC also supports slave transparent mode using a proprietary rate-matching scheme. IN SBC-code mode, linear 16-bit data at 16kHz (256kbps rate) is transferred over the PCM bus. Short Frame Sync, Master Mode Reference Description Min Typ Max Unit 1 PCM bit clock frequency - - 12.0 MHz 2 PCM bit clock High 41.0 - - ns 3 PCM bit clock Low 41.0 - - ns 4 PCM_SYNC delay 0 - 25.0 ns 5 PCM_OUT delay 0 - 25.0 ns

6 PCM_IN setup 8 - - ns

7 PCM_IN hold 8 - - ns

8 Delay from rising edge of PCM_BCLK during last bit

period to PCM_OUT becoming high impedance. 0 - 25.0 ns BT_PCM_CLK BT_PCM_SYNC BT_PCM_OUT BT_PCM_IN

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Short Frame Sync, Slave Mode Reference Description Min Typ Max Unit 1 PCM bit clock frequency - - 12.0 MHz 2 PCM bit clock High 41.0 - - ns 3 PCM bit clock Low 41.0 - - ns 4 PCM_SYNC setup 8.0 - - ns 5 PCM_SYNC hold 8.0 - - ns 6 PCM_OUT delay 0 - 25.0 ns 7 PCM_IN setup 8.0 - - ns 8 PCM_IN hold 8.0 - - ns

9 Delay from rising edge of PCM_BCLK during last bit

period to PCM_OUT becoming high impedance. 0 - 25.0 ns Long Frame Sync, Master Mode Reference Description Min Typ Max Unit 1 PCM bit clock frequency - - 12.0 MHz 2 PCM bit clock High 41.0 - - ns 3 PCM bit clock Low 41.0 - - ns 4 PCM_SYNC delay 0 - 25.0 ns 5 PCM_OUT delay 0 - 25.0 ns 6 PCM_IN setup 8.0 - - ns 7 PCM_IN hold 8.0 - - ns period to PCM_OUT becoming high impedance 0 - 25.0 ns BT_PCM_CLK BT_PCM_SYNC BT_PCM_OUT BT_PCM_IN BT_PCM_CLK BT_PCM_SYNC BT_PCM_OUT BT_PCM_IN

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Long Frame Sync, Slave Mode Reference Description Min Typ Max Unit 1 PCM bit clock frequency - - 12.0 MHz 2 PCM bit clock High 41.0 - - ns 3 PCM bit clock Low 41.0 - - ns 4 PCM_SYNC setup 8.0 - - ns 5 PCM_SYNC hold 8.0 - - ns 6 PCM_OUT delay 0 - 25.0 ns 7 PCM_IN setup 8.0 - - ns 8 PCM_IN hold 8.0 - - ns period to PCM_OUT becoming high impedance. 0 - 25.0 ns BT_PCM_CLK BT_PCM_SYNC BT_PCM_OUT BT_PCM_IN

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 13.4. Bluetooth I2S Interface Timing The IC used in the module supports I2S format. The module supports only PCM digital audio ports through I2S format. The I2S signals are:

• I2S clock: l2S SCK (Module pin: BT_PCM_CLK)
• I2S Word Select: l2S WS (Module pin: BT_PCM_SYNC)
• I2S Data Out: l2S SDO (Module pin: BT_PCM_OUT)
• I2S Data In: I2S SDI (Module pin: BT_PCM_IN) l2S SCK and I2S WS become outputs in master mode and inputs in slave mode, while I2S SDO always stays as an output. The channel word length is 16 bits and the data is justified so that the MSB of the let- channel data is aligned with the MSB of the l2S bus, per the I2S specification. The MSB of each data word is transmitted one bit clock cycle after the l2S WS transition, synchronous with the falling edge of bit clock. Left-channel data is transmitted when I2S WS is low, and right-channel data is transmitted when I2S WS is high. Data bits sent by the CYW89335 are synchronized with the falling edge of I2S_SCK and should be sampled by the receiver on the rising edge of l2S_SCK. The clock rate in master mode is either of the following: 48 kHz x 32 bits per frame = 1.536 MHz 48 kHz x 50 bits per frame = 2.400 MHz The master clock is generated from the input reference clock using a N/M clock divider. ln the slave mode, any clock rate is supported to a maximum of 3.072 MHz. Timing for I2S Transmitters and Receivers Transmitter Receiver Lower Limit Upper Limit Lower Limit Upper Limit Clock Period T Ttr - - - T r - - - a Master Mode: Clock generated by transmitter or receiver HIGH tHC 0.35T tr - - - 0.35T tr - - - b LOWLC 0.35T tr - - - 0.35T tr - - - b Slave Mode: Clock accepted by transmitter or receiver HIGH tHC - 0.35T tr - - - 0.35T tr - - c LOWLC - 0.35T tr - - - 0.35T tr - - c Rise time tRC - - 0.15T tr - - - - - d Transmitter Delay tdtr - - - 0.8T - - - - e Hold time thtr 0 - - - - - - - d Receiver Setup time tsr - - - - - 0.2T r - - f Hold time thr - - - - - 0 - - f (a). The system clock period T must be greater than Ttr and Tr because both the transmitter and receiver have to be able to handle the data transfer rate. (b). At all data rates in master mode, the transmitter or receiver generates a clock signal with a fixed mark/space ratio. For this reason, tHC and tLC specified with respect to T. (c). In slave mode, the transmitter and receiver need a clock signal with minimum HIGH and LOW periods so that they can detect the signal. So long as the minimum periods are greater than 0.35Ttr any clock that meets the requirements can be used. (d). Because the delay(tdtr) and the maximum transmitter speed (defined by Ttr) are related, a fast transmitter driven by a slow clock edge can result in tdtr not exceeding tRC which means thtr becomes zero or negative. Therefore, the transmitter has guarantee that thtr is greater than or equal to zero, so long as the clock rise-time tRC is not more than tRC where tRCmax is not less than 0.15Ttr. (e). To allow data to be clocked out on a falling edge, the delay is specified with respect to the rising edge of the clock signal and T, always giving the receiver sufficient setup time. (f). The data setup and hold time must not be less than the specified receiver setup and hold time.

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Note The time periods specified in below figures are defined by the transmitter speed. The receiver specifications must match transmitter performance. I2S Transmitters Timing I2S Receiver Timing

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 13.5. WLAN SDIO Timing 13.5.1. SDIO Default Mode Timing SDIO Bus Timing(a) Parameters (Default Mode) Parameter Symbol Min Typ Max Unit SDIO CLK (All values are referred to minimum VIH and maximum VIL(b) Frequency - Data Transfer Mode fPP 0 - 25 MHz Frequency - Identification Mode fOD 0 - 400 kHz Clock Low Time tWL 10.0 - - ns Clock High Time tWH 10.0 - - ns Clock Rise Time tTLH - - 10.0 ns Clock low Time tTHL - - 10.0 ns Inputs: CMD, DAT (referenced to CLK) Input Setup Time tISU 5.0 - - ns Input Hold Time tIH 5.0 - - ns Outputs: CMD, DAT (referenced to CLK) Output Delay time - Data Transfer Mode tODLY 0 - 14.0 ns Output Delay time - Identification Mode tODLY 0 - 50.0 ns (a). Timing is based on CL < 40pF load on CMD and Data. (b). Min (Vih) = 0.7*VIO and max (Vil) = 0.2*VIO.

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 13.5.2. SDIO High-Speed Mode Timing SDIO Bus Timing(a) Parameters (High-Speed Mode) Parameter Symbol Min Typ Max Unit SDIO CLK (All values are referred to minimum VIH and maximum VIL(b) Frequency - Data Transfer Mode fPP 0 - 50 MHz Frequency - Identification Mode fOD 0 - 400 kHz Clock Low Time tWL 7.0 - - ns Clock High Time tWH 7.0 - - ns Clock Rise Time tTLH - - 3.0 ns Clock low Time tTHL - - 3.0 ns Inputs: CMD, DAT (referenced to CLK) Input Setup Time tISU 6.0 - - ns Input Hold Time tIH 2.0 - - ns Outputs: CMD, DAT (referenced to CLK) Output Delay time - Data Transfer Mode tODLY - - 14.0 ns Output Delay time - Identification Mode tOH 2.5.0 - - ns Total system capacitance (each line) CL - - 40.0 pF (a). Timing is based on CL < 40pF load on CMD and Data. (b). Min (Vih) = 0.7*VIO and max (Vil) = 0.2*VIO.

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 13.5.3. SDIO Bus Timing Specifications in SDR Modes Clock Timing SDIO Clock Timing (SDR Modes) SDIO Bus Clock Timing Parameters (SDR Modes) Parameter Symbol Min. Max Unit Comments - t CLK 40.0 - ns SDR12 mode 20.0 - ns SDR25 mode 10.0 - ns SDR50 mode 4.8 - ns SDR104 mode - t CR, tCF - 0.2×tCLK ns tCR, tCF<2.00ns(max)@100MHz, CCARD=10pF tCR, tCF<0.96ns(max)@208MHz, CCARD=10pF Clock duty - 30.0 70.0 % -

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Device Input Timing SDIO Bus Input Timing (SDR Modes) SDIO Bus Input Timing Parameters (SDR Modes) Symbol Min Max Unit Comments SDR104 Mode tIS 1.4 - ns CCARD=10pF, VCT=0.975V tIH 0.8 - ns CCARD=5pF, VCT=0.975V SDR50 Mode tIS 3.0 - ns CCARD=10pF, VCT=0.975V tIH 0.8 - ns CCARD=5pF, VCT=0.975V SDR25 Mode tIS 3.0 - ns CCARD=10pF, VCT=0.975V tIH 0.8 - ns CCARD=5pF, VCT=0.975V SDR12 Mode tIS 3.0 - ns CCARD=10pF, VCT=0.975V tIH 0.8 - ns CCARD=5pF, VCT=0.975V

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Device Output Timing SDR Modes up to 100MHz SDIO Bus Output Timing Parameters (SDR Modes up to 100MHz) Symbol Min Max Unit Comments tODLY 7.5 ns tCLK≧10ns CL=30pF using driver typeB for SDR50 tODLY 14.0 ns tCLK≧20ns CL=40pF using for SDR12, SDR25 tOH 1.5 ns Hold time at the tODLY(min)CL=15pF SDR Modes 100MHz to 208MHz SDIO Bus Output Timing Parameters (SDR Modes 100MHz to 208MHz) Symbol Min Max Unit Comments tOP 0 2 UI Card output phase ΔtOP -350 +1550 Ps Delay variation due to temp change after tuning tODW 0.60 - UI tODW=2.88ns@208MHz ・ΔtOP=+1550ps for junction temperature of ΔtOP=90 degrees during operation. ・ΔtOP=-350ps for junction temperature of ΔtOP=-20 degrees during operation. ・ΔtOP=+2600ps for junction temperature of ΔtOP=-20 to +125 degrees during operation

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd.

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 14. ELECTORICAL CHARACTERISTICS 14.1. DC/RF Characteristics for IEEE802.11b - 2.4G Normal Condition : 25deg.C, VBAT =3.3V. 11Mbps mode unless otherwise specified. Items Contents Specification IEEE802.11b-2.4GHz Mode DSSS / CCK Channel frequency (spacing) 2412 to 2472 MHz (5MHz) Data rate 1, 2, 5.5,11Mbps Current Consumption Min. Typ. Max. Unit (a) Tx mode - 370 470 mA (b) Rx mode - 100 150 mA Transmitter Min. Typ. Max. Unit Power Levels 14.5 17 19.5 dBm Spectrum Mask (a) 1st side lobes - - -30 dBr (b) 2nd side lobes - - -50 dBr Power-on/off ramp - - 2.0 usec RF Carrier Suppression 15 - - dB Modulation Accuracy - - 35 % Frequency tolerance -20 - 20 ppm Spurious Emissions (BW=100kHz) (a) 30Hz≦f<1000MHz - - -36 dBm (b) 1000MHz≦f<12750MHz - - -30 dBm (c) 1800MHz<f≦1900MHz - - -47 dBm (d) 5150MHz<f≦5300MHz - - -47 dBm Receiver Min. Typ. Max. Unit Minimum Input Level (FER< 8%) - - -76 dBm Maximum Input Level (FER < 8%) -10 - - dBm Adjacent Channel Rejection (FER < 8%) 35 - - dB

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 14.2. DC/RF Characteristics for IEEE802.11g - 2.4G Normal Condition : 25deg.C, VBAT =3.3V. 54Mbps mode unless otherwise specified. Items Contents Specification IEEE802.11g-2.4GHz Mode OFDM Channel frequency (spacing) 2412 to 2472 MHz (5MHz) Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps Current Consumption Min. Typ. Max. unit (a) Tx mode - 330 430 mA (b) Rx mode - 100 150 mA Transmitter Min. Typ. Max. unit Power Levels 12.5 15 17.5 dBm Spectrum Mask (a) at fc +/- 11MHz - - -20 dBr (b) at fc +/- 20MHz - - -28 dBr (c) at fc > +/-30MHz - - -40 dBr Constellation Error - - -25 dB Frequency tolerance -20 20 ppm Spurious Emissions (BW=100kHz) (a) 30Hz≦f<1000MHz - - -36 dBm (b) 1000MHz≦f<12750MHz - - -30 dBm (c) 1800MHz<f≦1900MHz - - -47 dBm (d) 5150MHz<f≦5300MHz - - -47 dBm Receiver Min. Typ. Max. unit Minimum Input Level (PER < 10%) - - -65 dBm Maximum Input Level (PER < 10%) -20 - - dBm Adjacent Channel Rejection (PER < 10%) -1 - - dB

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 14.3. DC/RF Characteristics for IEEE802.11n - 2.4GHz Normal Condition : 25deg.C, VBAT =3.3V. 65Mbps (MCS7 – HT 20MHz) mode unless otherwise specified. Items Contents Specification IEEE802.11n-2.4GHz Mode OFDM Channel frequency (spacing) 2412 to 2472 MHz (5MHz) Data rate 6.5, 13, 19.5, 26, 39, 52, 58.5, 65Mbps Current Consumption Min. Typ. Max. unit (a) Tx mode - 330 430 mA (b) Rx mode - 100 150 mA Transmitter Min. Typ. Max. unit Power Levels 12.5 15 17.5 dBm Spectrum Mask (a) at fc +/- 11MHz - - -20 dBr (b) at fc +/- 20MHz - - -28 dBr (c) at fc > +/-30MHz - - -45 dBr Constellation Error (measured at enhanced mode) - - -27 dB Frequency tolerance -20 - 20 ppm Spurious Emissions (BW=100kHz) (a) 30Hz≦f<1000MHz - - -36 dBm (b) 1000MHz≦f<12750MHz - - -30 dBm (c) 1800MHz<f≦1900MHz - - -47 dBm (d) 5150MHz<f≦5300MHz - - -47 dBm Receiver Min. Typ. Max. unit Minimum Input Level (PER < 10%) - - -64 dBm Maximum Input Level (PER < 10%) -20 - - dBm Adjacent Channel Rejection (PER < 10%) -2 - - dB

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 14.4. DC/RF Characteristics for IEEE802.11a - 5GHz Normal Condition : 25deg.C, VBAT =3.3V. 54Mbps mode unless otherwise specified. Items Contents Specification IEEE802.11a-5GHz Mode OFDM Channel frequency (spacing) 5180 - 5825MHz Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps Current Consumption Min. Typ. Max. Unit (a) Tx mode - 400 500 mA (b) Rx mode - 120 170 mA Transmitter Min. Typ. Max. Unit Power Levels 11.5 14 16.5 dBm Spectrum Mask (a) at fc +/- 11MHz - - -20 dBr (b) at fc +/- 20MHz - - -28 dBr (c) at fc > +/-30MHz - - -40 dBr Constellation Error - - -25 dB Frequency tolerance -20 20 ppm Spurious Emissions (BW=100kHz) (a) 30Hz≦f<1000MHz - - -36 dBm (b) 1000MHz≦f<26000MHz - - -30 dBm Receiver Min. Typ. Max. Unit Minimum Input Level (PER < 10%) - - -65 dBm Maximum Input Level (PER < 10%) -30 - - dBm Adjacent Channel Rejection (PER < 10%) -1 dB

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 14.5. DC/RF Characteristics for IEEE802.11n(HT 20MHz) - 5GHz Normal Condition : 25deg.C, VBAT =3.3V. 65Mbps (MCS7 – HT 20MHz) mode unless otherwise specified. Items Contents Specification IEEE802.11n-5GHz Mode OFDM Channel frequency (spacing) 5180 - 5825MHz Data rate 6.5, 13, 19.5, 26, 39, 52, 58.5, 65Mbps Current Consumption Min. Typ. Max. Unit (a) Tx mode - 380 480 mA (b) Rx mode - 120 170 mA Transmitter Min. Typ. Max. Unit Power Levels 10.5 13 15.5 dBm Spectrum Mask (a) at fc +/- 11MHz - - -20 dBr (b) at fc +/- 20MHz - - -28 dBr (c) at fc > +/-30MHz - - -40 dBr Constellation Error (measured at enhanced mode) - - -27 dB Frequency tolerance -20 20 ppm Spurious Emissions (BW=100kHz) (a) 30Hz≦f<1000MHz - - -36 dBm (b) 1000MHz≦f<26000MHz - - -30 dBm Receiver Min. Typ. Max. Unit Minimum Input Level (PER < 10%) - - -64 dBm Maximum Input Level (PER < 10%) -30 - - dBm Adjacent Channel Rejection (PER < 10%) 16 - - dB

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 14.6. DC/RF Characteristics for IEEE802.11n(HT 40MHz) - 5GHz Normal Condition : 25deg.C, VBAT =3.3V. 135Mbps (MCS7 – HT 40MHz) mode unless otherwise specified. Items Contents Specification IEEE802.11n-5GHz Mode OFDM Channel frequency (spacing) 5180 - 5825MHz Data rate 13.5,27,40.5,54,81,108,121.5,135Mbps Current Consumption Min. Typ. Max. Unit (a) Tx mode - 410 510 mA (b) Rx mode - 140 190 mA Transmitter Min. Typ. Max. Unit Power Levels 9.5 12 14.5 dBm Spectrum Mask (a) at fc +/- 21MHz - - -20 dBr (b) at fc +/- 40MHz - - -28 dBr (c) at fc > +/-60MHz - - -40 dBr Constellation Error (measured at enhanced mode) - - -27 dB Frequency tolerance -20 20 ppm Spurious Emissions (BW=100kHz) (a) 30Hz≦f<1000MHz - - -36 dBm (b)1000MHz≦f<26000MHz - - -30 dBm Receiver Min. Typ. Max. Unit Minimum Input Level (PER < 10%) - - -61 dBm Maximum Input Level (PER < 10%) -30 - - dBm Adjacent Channel Rejection (PER < 10%) -2 dB

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 14.7. DC/RF Characteristics for IEEE802.11ac(HT 40MHz) - 5GHz Normal Condition : 25deg.C, VBAT =3.3V. 180Mbps (MCS9 – HT 40MHz) mode unless otherwise specified. Items Contents Specification IEEE802.11ac-5GHz Mode OFDM Channel frequency (spacing) 5190 - 5795MHz Data rate 13.5,27,40.5,54,81,108,121.5,135,162,180Mbps Current Consumption Min. Typ. Max. Unit (a) Tx mode - 420 520 mA (b) Rx mode - 140 200 mA Transmitter Min. Typ. Max. Unit Power Levels 7.5 10 12.5 dBm Spectrum Mask (a) at fc +/- 21MHz - - -20 dBr (b) at fc +/- 40MHz - - -28 dBr (c) at fc > +/-60MHz - - -40 dBr Constellation Error (measured at enhanced mode) - - -32 dB Frequency tolerance -20 20 ppm Spurious Emissions (BW=100kHz) (a) 30Hz≦f<1000MHz - - -36 dBm (b) 1000MHz≦f<26000MHz - - -30 dBm Receiver Min. Typ. Max. Unit Minimum Input Level (PER < 10%) - - -54 dBm Maximum Input Level (PER < 10%) -30 - - dBm

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 14.8. DC/RF Characteristics for IEEE802.11ac(HT 80MHz) - 5GHz Normal Condition : 25deg.C, VBAT =3.3V. 390Mbps (MCS9 – HT 80MHz) mode unless otherwise specified. Items Contents Specification IEEE802.11ac-5GHz Mode OFDM Channel frequency (spacing) 5210 - 5775MHz Mbps Current Consumption Min. Typ. Max. Unit (a) Tx mode - 440 540 mA (b) Rx mode - 180 250 mA Transmitter Min. Typ. Max. Unit Power Levels 7.5 10 12.5 dBm Spectrum Mask (a) at fc +/- 41MHz - - -20 dBr (b) at fc +/- 80MHz - - -28 dBr (c) at fc > +/-120MHz - - -40 dBr Constellation Error (measured at enhanced mode) - - -32 dB Spurious Emissions (BW=100kHz) (a) 30Hz≦f<1000MHz - - -36 dBm (b)1000MHz≦f<26000MHz - - -30 dBm Receiver Min. Typ. Max. Unit Minimum Input Level (PER < 10%) - - -51 dBm Maximum Input Level (PER < 10%) -30 - - dBm Adjacent Channel Rejection (PER < 10%) -9 dB

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 14.9. DC/RF Characteristics for Bluetooth Normal conditions : 25 deg.C, VBAT = 3.3V Items Contents Bluetooth specification (power class) Version 5.2 (Class2) Channel frequency (spacing) 2402 to 2480 MHz (1MHz) Current Consumption Min. Typ. Max. unit (a) DH5 Packet 50% Rx/Tx slot duty cycle - 50 65 mA (b) 2DH5 Packet 50% Rx/Tx slot duty cycle - 40 55 mA (c) 3DH5 Packet 50% Rx/Tx slot duty cycle - 40 45 mA Transmitter Min. Typ. Max. Unit Output Power (at 1DH5) 7.5 11 14.5 dBm Frequency range 2400 - 2483.5 MHz 20dB bandwidth - 1 MHz Adjacent Channel Power *1 (a) [M-N] =2 - - -20 dBm (b) [M-N] ≥3 - - -40 dBm Modulation characteristics (a) Modulation Δf1avg 140 - 175 kHz (b) Modulation Δf2max 115 - kHz (c) Modulation Δf2avg / Δf1avg 0.8 - - Carrier Frequency Drift (a) 1slot -25 - +25 kHz (b) 3slot / 5slot -40 - +40 kHz (c) Maximum drift rate -20 - +20 kHz/5 0us EDR Relative Power -4 - +1 dB EDR Carrier Frequency Stability and Modulation Accuracy (a) ωi -75 - +75 kHz (b) ωi+ωo -75 - +75 kHz (c) ωo -10 - +10 kHz (d) RMS DEVM (DQPSK) - - 20 % (e) Peak DEVM (DQPSK) - - 35 % (f) 99% DEVM (DQPSK) - - 30 % (g) RMS DEVM (8DPSK) - - 13 % (h) Peak DEVM (8DPSK) - - 25 % (i) 99% DEVM (8DPSK) - - 20 % Spurious Emissions (BW=100kHz) (a) 30Hz≦f<1000MHz - - -36 dBm (b)1000MHz≦f<12750MHz - - -30 dBm (c) 1800MHz<f≦1900MHz - - -47 dBm (d) 5150MHz<f≦5300MHz - - -47 dBm Receiver Min. Typ. Max. unit Sensitivity (BER<0.1%) - - -80 dBm Maximum Input Level (BER<0.1%) -20 - - dBm EDR Sensitivity (BER<0.007%) (a) 8DPSK - - -70 dBm *1: Up to three spurious responses within Bluetooth limits are allowed.

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 14.10. DC/RF Characteristics for Bluetooth (LE) Conditions : 25deg.C, VBAT=3.3V Items Contents Bluetooth specification (power class) Version 5.2(LE) Channel frequency (spacing) 2402 to 2480 MHz (2MHz) Number of RF Channel 40 Current Consumption Min. Typ. Max. Unit (a) Tx mode - 30 45 mA (b) Rx mode - 15 25 mA Item / Condition Min. Typ. Max. Unit Center Frequency 2402 - 2480 MHz Channel Spacing - 2 - MHz Number of RF channel - 40 - - Output power 0 3 7.5 dBm Modulation Characteristics 1) Δf1avg 225 - 275 kHz 2) Δf2max (at 99.9%) 185 - - kHz 3) Δf2avg / Δf1avg 0.8 - - - Carrier frequency offset and drift 1) Frequency offset - - 150 kHz 2) Frequency drift - - 50 kHz 3) Drift rate - - 20 kHz Receiver sensitivity (PER < 30.8%) - - -70 dBm Maximum input signal level (PER < 30.8%) -10 - - dBm PER Report Integrity (-30dBm input) 50 - 65.4 %

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 15. Land Pattern Top View. Unit : mm 0.3 0.55 0.475 0.25 0.25 1.05 0.55 0.9 0.8 0.6 0.6 0.8 0.25 1.475 1.65 0.55

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 16. TAPE AND REEL PACKING (1) Dimensions of Tape (Plastic tape) (2) Dimensions of Reel 2.0±0.1 1.75±0.10 0.30±0.05 1.55 ±0.05 16.0±0.1 11.5±0.1  1.5+0.1/-0.0 24.0+0.3/-0.1 feeding direction 4.0±0.1 7.6±0.05 2.0+0.1/-0.0 10.5±0.05 13.0±0.2 2.0±0.5 25.4±1.0 30.4 max. 100330

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. (3) Taping Diagrams [1] Feeding Hole : As specified in (1) [2] Hole for chip : As specified in (1) [3] Cover tape : 62 um in thickness [4] Base tape : As specified in (1) (4) Leader and Tail tape Feeding Hole Chip Feeding Direction Pin 1 Marking Tail tape (No components) 40 to 200mm Components No components 150mm min. Leader tape (Cover tape alone) 250mm min. Feeding direction [2] [3] [4] [3] [1]

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. (5) The tape for chips are wound clockwise, the feeding holes to the right side as the tape is pulled toward the user. (6) The cover tape and base tape are not adhered at no components area for 250mm min. (7) Tear off strength against pulling of cover tape: 5N min. (8) Packaging unit : 1000pcs./ reel (9) material - Base tape : Plastic Reel : Plastic Cover tape, cavity tape and reel are made the anti-static processing. (10) Peeling of force: 1.1N max. in the direction of peeling as shown below. (11) PACKAGE (Humidity proof packing) Tape and reel must be sealed with the anti-humidity plastic bag. The bag contains the desiccant and the humidity indicator. 湿度インジケ－タ 乾燥剤 表示ラべル 防湿梱包袋 表示ラベルLabel Label Desiccant Humidity Indicator Anti-humidity Plastic Bag 165 to 180 ° 1.1 N max. Base tape Cover tape

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 17. NOTICE 17.1. Storage Conditions: Please use this product within 6month after receipt. - The product shall be stored without opening the packing under the ambient temperature from 5 to 35deg.C and humidity from 20 to 70%RH. (Packing materials, in particular, may be deformed at the temperature over 40deg.C.) - The product left more than 6months after reception, it needs to be confirmed the solderability before used. - The product shall be stored in non corrosive gas (Cl2, NH3, SO2, Nox, etc.). - Any excess mechanical shock including, but not limited to, sticking the packing materials by sharp object and dropping the product, shall not be applied in order not to damage the packing materials. This product is applicable to MSL3 (Based on JEDEC Standard J-STD-020) - After the packing opened, the product shall be stored at <30deg.C / <60%RH and the product shall be used within 168hours. - When the color of the indicator in the packing changed, the product shall be baked before soldering. Baking condition: 125+5/-0deg.C, 24hours, 1time The products shall be baked on the heat-resistant tray because the materials (Base Tape, Reel Tape and Cover Tape) are not heat-resistant. 17.2. Handling Conditions: Be careful in handling or transporting products because excessive stress or mechanical shock may break products. Handle with care if products may have cracks or damages on their terminals, the characteristics of products may change. Do not touch products with bear hands that may result in poor solder ability and destroy by static electrical charge. 17.3. Standard PCB Design (Land Pattern and Dimensions): All the ground terminals should be connected to the ground patterns. Furthermore, the ground pattern should be provided between IN and OUT terminals. Please refer to the specifications for the standard land dimensions. The recommended land pattern and dimensions is as Murata's standard. The characteristics of products may vary depending on the pattern drawing method, grounding method, land dimensions, land forming method of the NC terminals and the PCB material and thickness. Therefore, be sure to verify the characteristics in the actual set. When using non-standard lands, contact Murata beforehand. 17.4. Notice for Chip Placer: When placing products on the PCB, products may be stressed and broken by uneven forces from a worn- out chucking locating claw or a suction nozzle. To prevent products from damages, be sure to follow the specifications for the maintenance of the chip placer being used. For the positioning of products on the PCB, be aware that mechanical chucking may damage products.

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 17.5. Soldering Conditions: The recommendation conditions of soldering are as in the following figure. Soldering must be carried out by the above mentioned conditions to prevent products from damage. Set up the highest temperature of reflow within 260 °C. Contact Murata before use if concerning other soldering conditions. Reflow soldering standard conditions (Example) Please use the reflow within 2 times. Use rosin type flux or weakly active flux with a chlorine content of 0.2 wt % or less. 17.6. Cleaning: Since this Product is Moisture Sensitive, any cleaning is not recommended. If any cleaning process is done the customer is responsible for any issues or failures caused by the cleaning process. 17.7. Operational Environment Conditions: Products are designed to work for electronic products under normal environmental conditions (ambient temperature, humidity and pressure). Therefore, products have no problems to be used under the similar conditions to the above-mentioned. However, if products are used under the following circumstances, it may damage products and leakage of electricity and abnormal temperature may occur. - In an atmosphere containing corrosive gas (Cl2, NH3, SOx, NOx, etc.). - In an atmosphere containing combustible and volatile gases. - Dusty place. - Direct sunlight place. - Water splashing place. - Humid place where water condenses. - Freezing place. If there are possibilities for products to be used under the preceding clause, consult with Murata before actual use. As it might be a cause of degradation or destruction to apply static electricity to products, do not apply static electricity or excessive voltage while assembling and measuring. Within 120s Pre-heating time(s) 220 deg.C Within 60s Cooling down Slowly 180 deg.C 150 deg.C 250 deg.C Within 10s Tpeak-5deg.C

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 17.8. Input Power Capacity: Products shall be used in the input power capacity as specified in this specification. Inform Murata beforehand, in case that the components are used beyond such input power capacity range.

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 18. PRECONDITION TO USE OUR PRODUCTS PLEASE READ THIS NOTICE BEFORE USING OUR PRODUCTS. Please make sure that your product has been evaluated and confirmed from the aspect of the fitness for the specifications of our product when our product is mounted to your product. All the items and parameters in this product specification/datasheet/catalog have been prescribed on the premise that our product is used for the purpose, under the condition and in the environment specified in this specification. You are requested not to use our product deviating from the condition and the environment specified in this specification. Please note that the only warranty that we provide regarding the products is its conformance to the specifications provided herein. Accordingly, we shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this specification. WE HEREBY DISCLAIMS ALL OTHER WARRANTIES REGARDING THE PRODUCTS, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, THAT THEY ARE DEFECT-FREE, OR AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. The product shall not be used in any application listed below which requires especially high reliability for the prevention of such defect as may directly cause damage to the third party's life, body or property. You acknowledge and agree that, if you use our products in such applications, we will not be responsible for any failure to meet such requirements. Furthermore, YOU AGREE TO INDEMNIFY AND DEFEND US AND OUR AFFILIATES AGAINST ALL CLAIMS, DAMAGES, COSTS, AND EXPENSES THAT MAY BE INCURRED, INCLUDING WITHOUT LIMITATION, ATTORNEY FEES AND COSTS, DUE TO THE USE OF OUR PRODUCTS IN SUCH APPLICATIONS. - Aircraft equipment. - Aerospace equipment - Undersea equipment. - Power plant control equipment - Medical equipment. - Traffic signal equipment. - Burning / explosion control equipment - Disaster prevention / crime prevention equipment. - Transportation equipment (vehicles, trains, ships, elevator, etc.). - Application of similar complexity and/ or reliability requirements to the applications listed in the above. We expressly prohibit you from analyzing, breaking, reverse-engineering, remodeling altering, and reproducing our product. Our product cannot be used for the product which is prohibited from being manufactured, used, and sold by the regulations and laws in the world. We do not warrant or represent that any license, either express or implied, is granted under any our patent right, copyright, mask work right, or our other intellectual property right relating to any combination, machine, or process in which our products or services are used. Information provided by us regarding third-party products or services does not constitute a license from us to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from us under our patents or other intellectual property. Please do not use our products, our technical information and other data provided by us for the purpose of developing of mass-destruction weapons and the purpose of military use. Moreover, you must comply with "foreign exchange and foreign trade law", the "U.S. export administration regulations", etc. Please note that we may discontinue the manufacture of our products, due to reasons such as end of supply of materials and/or components from our suppliers. By signing on specification sheet or approval sheet, you acknowledge that you are the legal representative for your company and that you understand and accept the validity of the contents herein. When you are not able to return the signed version of specification sheet or approval sheet within 30 days from receiving date of specification sheet or approval sheet, it shall be deemed to be your consent on the content of specification sheet or approval sheet. Customer acknowledges that engineering samples may deviate from specifications and may contain defects due to their development status. We reject any liability or product warranty for engineering samples. In particular we disclaim liability for damages caused by - the use of the engineering sample other than for evaluation purposes, particularly the installation or integration in the product to be sold by you, -deviation or lapse in function of engineering sample, -improper use of engineering samples. We disclaim any liability for consequential and incidental damages. If you can’t agree the above contents, you should inquire our sales.

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Appendix

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. User Manual For FCC Model Name: LBEE5XV2BZ FCC ID: VPYLBEE5XV1XA Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification (installation procedure) The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the end user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as shown in User manual.

• The following information must be indicated on the host device of this module. Contains Transmitter Module FCC ID:VPYLBEE5XV1XA or Contains FCC ID: VPYLBEE5XV1XA This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. *If it is difficult to describe this statement on the host product due to the size, please describe in the User's manual. please describe in the user's manual and also either describe on the device packaging or on a removable label attached to the device.
• The following statements must be described on the user manual of the host device of this module; FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. When installing it in a mobile equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body. When installing it in a portable equipment. It is necessary to take a SAR test with your set mounting this module. Class II permissive change application is necessary using the SAR report. Please contact Murata. Note) Portable equipment: Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment: Equipment used at position in which the spaces between human body and antenna exceeded 20cm. Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. Frequency Tolerance: ±20 ppm

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. For ISED Model Name: “LBEE5XV2BZ_SANT”, “LBEE5XV2BZ_DANT” IC Number: 772C-LBEE5XV1XA Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification (installation procedure). The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the end user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as shown in User manual.

• The following information must be indicated on the host device of this module. Contains IC: 772C-LBEE5XV1XA
• In case of the final product which can be carried around to outdoor. The following indication is necessary to the final product. ・When the STA function is used in channel 52, 54, 58 At the time of the channel 52 or 54 or 58 setting, please indicate “for indoor use only channel”. During connecting, please show the channel number which connects. And please indicate that the end user may find out "for indoor use only channel".
• If the final product use the following frequency, please note that there is a limit. for indoor use only (5150-5250MHz band) Pour usage intérieur seulement (5150-5250MHz band)
• The following statements must be described on the user manual of the host device of this module; This device complies with Industry Canada’s applicable license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) l’appareil ne doit pas produire de brouillage; 2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
• When installing it in a mobile equipment. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body. Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain.

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd.

• When installing it in a portable equipment. It is necessary to take a SAR test with your set mounting this module. Class 4 permissive change application is necessary using the SAR report. Please contact Murata. Note) Portable equipment: Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment: Equipment used at position in which the spaces between human body and antenna exceeded 20cm. Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. La transmission des données est toujours initiée par le logiciel, puis les données sont transmises par l'intermédiaire du MAC, par la bande de base numérique et analogique et, enfin, à la puce RF. Plusieurs paquets spéciaux sont initiés par le MAC. Ce sont les seuls moyens pour qu'une partie de la bande de base numérique active l'émetteur RF, puis désactive celui-ci à la fin du paquet. En conséquence, l'émetteur reste uniquement activé lors de la transmission d'un des paquets susmentionnés. En d'autres termes, ce dispositif interrompt automatiquement toute transmission en cas d'absence d'information à transmettre ou de défaillance. This radio transmitter (IC Number: 772C-LBEE5XV1XA) has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Le présent émetteur radio (IC Number: 772C-LBEE5XV1XA) a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd.

• RF Power Please ask Murata
• Operation mode and frequency band WLAN STA 2.4GHz 11b/g/n/ac HT20 1ch-11ch 5GHz 11a HT20 W52/53/56/58 with ch144/142/138 DFS (Device without Radar detection capability) No TPC 11n HT20/40 11ac VHT20/40/80 AP 2.4GHz 11b/g/n/ac HT20 1ch-11ch 5GHz 11a HT20 W52/58 with ch144/142/138 No TPC 11n HT20/40 11ac VHT20/40/80 BT BR / EDR / LE (1/2Mbps)

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd.

• Theory of Operation-Channel List Frequency of operation Scan Ad-hoc mode 2.4GHz 11b/g/n (HT20) 2412-2462MHz Active Yes BT 2402-2480MHz N/A N/A BLE 2402-2480MHz N/A N/A W52 11a/n/ac ((V)HT20) 5180-5240MHz Active Yes 11n/ac ((V)HT40) 5190-5230MHz Active Yes 11ac (VHT80) 5210MHz Active Yes W53 11a/n/ac ((V)HT20) 5260-5320MHz Passive No 11n/ac ((V)HT40) 5270-5310MHz Passive No 11ac (VHT80) 5290MHz Passive No W56 11a/n/ac ((V)HT20) 5500-5720MHz * Passive No 11n/ac ((V)HT40) 5510-5710MHz * Passive No 11ac (VHT80) 5530-5690MHz * Passive No W58 11a/n/ac ((V)HT20) 5745-5825MHz Active Yes 11n/ac ((V)HT40) 5755-5795MHz Active Yes 11ac (VHT80) 5775MHz Active Yes * The frequency band 5600MHz-5640MHz (11a/n/ac 20M band), 5590MHz-5630MHz (11n/ac 40M band) and 5610MHz (11ac 80M band) is restricted in ISED. Notes: End users cannot modify the software because F/W & driver are installed in device.

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd.

• Antenna ■Certified Antenna information P/N Form factor Type Gain (dBi) 2.4Ghz 5Ghz 1 Molex 146153 u.FL/flexible dipole 3.2 4.25 2 Molex 146187 u.FL/flexible dipole 3.4 4.75 ■Please perform the antenna design that followed the specifications of the antenna. ■About the signal line between an antenna and a module It is a 50-ohm line design. Fine tuning of return loss etc. can be performed using a matching network. However, it is required to check "Class1 change" and "Class2 change" which the authorities define then. The concrete contents of a check are the following three points. 1) It is the same type as the antenna type of antenna specifications. 2) An antenna gain is lower than a gain given in antenna specifications. 3) The emission level is not getting worse. The following is the design of the EVB used for the test. ANT0

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. ANT1 ANT2

Specification Number: SP-XV2BZ-A < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. For Japan Certification Number: 007-AJ0192 This module is a product that has been authorized construction design certification based on the following Certificate of Construction Type. [(Warning) In the 5 GHz frequency band, three types of 5.2 GHz / 5.3 GHz / 5.6 GHz bands (W52 / W53 / W56) can be used. Outdoor use of the 5.2 GHz / 5.3 GHz band wireless LAN (W52 / W53) is prohibited by the Certificate of Construction Type.] W53 / W56 for STA function only.

• It is recommended to describe the following contents in the end product or user manual. ・[This product has built-in specified radio equipment which received construction design certification (certification number: 007-AJ0192) based on the Certificate of Construction.] ・[The W52 / W53 in the 5 GHz band is prohibited from outdoor use under the Japanese Certificate of Construction Type.] R 007-AJ0192 W52/53 is for indoor use only