LB1843V

LB1843V ONSEMI | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 10

Technical content

22814NK B8-7154 / O3096HA(II) No.4385-1/10 Semiconductor Components Industries, LLC, 2014 February, 2014 http://onsemi.com

ORDERING INFORMATION

See detailed ordering and shipping information on page 10 of this data sheet. LB1843V Overview The LB1843V is a low-saturation bidirectional motor driver with output current limitation and detection functions. This design is ideal for controlling the loading motor in a video camera. Function

• Output current limiter and detector built in.
• Low-saturation voltage bidirectional bridge circuit built in: VOsat = 0.40 V typ. at 400 mA.
• Practically no current drain (0.1 μA or less) in standby mode.
• Input-linked reference voltage built in .
• Thermal shutdown circuit built in.
• Requires little space, since few external components are needed and the IC is contained in a small SSOP-20 package Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Symbol Conditions Ratings Unit Maximum supply voltage V CC max 10.5 V Maximum output current Im max 800 mA Applied Input voltage V IN -0.3 to +10 V Allowable power dissipation Pd max With board (50x35x1.6mm) 800 mW Operating temperature Topr -20 to +80 °C Storage temperature Tstg -40 to +150 °C Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time. Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current, high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details. Recommended Operating Conditions at Ta = 25°C Parameter Symbol Conditions Ratings Unit min typ max Supply voltage V CC 3.0 9.0 V VM voltage V M 2.2 V CC V High-level input voltage V IH 3.0 9.0 V Low-level input voltage V IL -0.3 +0.7 V LIR input voltage V LIR 0.5 V CC-1.0 V Output current limitation I limit 50 350 mA Monolithic Linear IC Low-saturation, current-controlled bidirectional motor driver Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. SSOP20 (225mil) Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recomme nded Operating Ranges limits mayaffect device reliability.

No.4385-2/10 Electrical Characteristics at Ta = 25°C, VCC = 7.2V Parameter Symbol Conditions Ratings Unit min typ max Supply current I CC0 During standby 0.1 10 μA ICC1 During bidirectional operation, no load 9 13 mA ICC2 During braking 12 18 mA Output saturation voltage (upper side + lower side) Vsat1 I OUT = 200mA (upper side + lower side) 0.20 0.30 V Vsat2 I OUT = 400mA (upper side + lower side) 0.40 0.60 V Reference voltage V ref I Vref = 1mA 1.85 2.0 2.15 V Set output current I limit Resistance between V CC and VM = 1Ω, when LIR = 2V 165 185 205 mA Input current I IN V IN = 5V 90 150 μA RD saturation voltage V RDsat I o = 1mA 0.3 V Output current limit is determined by the following equation (Rf is the sensing resistance between VCC and VM): I limit = VLIR / 10Rf (A) The input range for VLIR is 0.5 to VCC – 1.0(V) Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product per formance may not be indicated by the Electrical Characteristics if operated under different conditions.

No.4385-3/10 Package Dimensions SSOP20 (225mil) CASE 565AN ISSUE A XXXXXXXXXX YMDDD XXXXX = Specific Device Code Y = Year M = Month DDD = Additional Traceability Data GENERIC MARKING DIAGRAM* *This information is generic. Please refer to device data sheet for actual part marking. SOLDERING FOOTPRINT* NOTE: The measurements are not to guarantee but for reference only. (Unit: mm) *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. 1.0 5.80 0.32 0.65

No.4385-4/10 Block Diagram and Sample Application Circuit Pin Assignment

No.4385-5/10 Pin Functions Pin No. Pin name Pin Function Equivalent Circuit IN1 IN2 Control signal input pin Control signal input pin 50K 80K VCC S-GND

15 DEL Control signal input pin

4,5 2,3 18,19 VM OUT1 OUT2 Output current detect pin Out pin Out pin Continued on next page.

No.4385-6/10 Continued from preceding page.

9 Vref Reference voltage output pin

12 RD Lock detect signal output pin

17 LIR Output current setting pin

6 V CC Power supply voltage pin

11 S-GND Signal ground pin

1,20 P-GND Power ground pin 7,8,10,16 NC No connect

No.4385-7/10 Truth Table Input Output Mode IN1 IN2 OUT1 OUT2 L L Off Off Standby H L H L Forward L H L H Reverse H H L L Brake Output Current Limitation and Detector Output DEL OUT output RD H Limit L Non-limit Off L Saturated Off Sample Application Timing Chart Sample application timing chart 1) Connect a DC motor (RL = R) between OUT1 and OUT2, and with the RD pin pulled up, input a forward rotation signal (IN1 = high, IN2 = low). Because the output is used in the saturated state at startup, set the DEL input to low. 2) The DC motor starts up, and the startup current (IST = VM/R) flows to the motor. 3) The DC motor rotates in the normal state. At this point, set the DEL input to high. 4) If the DC motor locks, the motor current IM increases to the point of Ilimit (= VLIR/(10Rf)), the output current limiter operates to limit the output current. At the same time, RD is output low from the set current detection circuit.

No.4385-8/10 Reference voltage (Vref) The Vref output is linked to the input; if either IN1 or IN2 is high, the reference voltage is output. Output current limiter The schematic for the output current limiter is shown below. The output set current is set according to the reference voltage VLIR applied to the LIR pin. When VLIR is applied, 1/10 of that voltage is generated at both ends of RS in the diagram; this voltage is input on the positive (+) side of the current setting amplifier. The motor current IM generates voltage equal to (IM ´ Rf) at both ends of the external resistor Rf. This voltage is input to the negative (–) side of the same amplifier, and the differential amplifier functions and the output transistors are driven so that these inputs become equal. The set current value in this instance is determined by the following equation: Ilimit = VLIR/(10Rf) [A] Set current detector (1) When DEL = high If the motor current IM has not reached the set current Il imit, the input voltage on th e negative (–) side of the amplifier is greater than the input voltage on the positive (+) side. As a result, the drive current increases and the output PNP transistors reach the saturation state. If this state is detected, the detection signal is sent to the set current detector, and the RD output goes high. If the motor current IM reaches the set current Ilimit, the output PNP transistor enters the controlled state, and the RD output goes low. (2) When DEL = low Because the operation of the current se tting amplifier is cancelled when a low si gnal is input to the DEL pin, the output PNP transistors reach the saturation state and the RD output goes high, just as in the case described above. The following table summarizes the states described above. DEL OUT output RD H Limit L Non-limit Off L Saturated Off Output Current Limiter and Set Current Detector Block Diagram

No.4385-9/10 ILB00874 861 0 1 224 7 59 1 1130 ICC -- VCC Current drain, ICC -- mA Supply voltage, VCC -- V ILB00875 IIN -- VIN Input current, IIN -- mA Input voltage, VIN -- V 120 160 240 200 9678 1 0 1 1123450 VCC=6.0VVIN=3V LIR=Vref Rf=0.5W, no load Brake DEL=L DEL=H ILB00876 Ilimit -- VLIR Set output current, Ilimit -- mA VLIR -- V 200 100 300 600 400 500 VCC=6.0V RL=10W Rf=0.5W 1.0W ILB00877 Ilimit -- VCC Set output current, Ilimit -- mA Supply voltage, VCC -- V 200 100 300 400 567 1 1 89 1 012340 Ilimit=300mA 200mA 100mA ILB00878 VO(sat) -- IO Output saturation voltage, VO(sat) -- V Output current, IO -- mA 0.2 0.1 0.3 0.5 0.4 0.6 300200 400 500 600 700 8001000 VCC=6.0V VIN=3.0V LIR=Vref DEL=L ILB00879 VO(sat) -- Ta Output saturation voltage, VO(sat) -- V 0.2 0.1 0.3 0.4 200 160 14040 60 80 100 120--20--40 VCC=6.0V VIN=3.0V LIR=Vref DEL=L IO=400mA 200mA Bidirectional

PS No.4385-10/10 Device Package Shipping (Qty / Packing) LB1843V-MPB-E SSOP20 (225mil) (Pb-Free / Halogen Free) 70 / Fan-Fold LB1843V-TLM-E SSOP20 (225mil) (Pb-Free / Halogen Free) 2000 / Tape & Reel ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequentia l or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use a s components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and dis tributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personali n j u r yo r death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture oft h e part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.