L000151-01 TEC | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 4
Technical content
DATA AND DEVICES / VFP69383B22JN VFP69383B22JN 698-960/1690-3800 MHz and 2400-2500/4900-6000 MHz Assembly and Installation Instructions ELECTRICAL SPECIFICATIONS Antenna Model VFP69383B22JN-518J ANumber of Ports 5 Port Configuration 2x- 3G/4G/ISM/CBRS 2x- Wi-Fi Operating Frequency (MHz) 698-806 824-894 880-960 1690-3800 2400-2500 4900-6000 Isolation (dB)– Gnd. Plane [No Gnd. Plane] LTE1 to LTE2 -11 [-11] LTE1 to WIFI -36 [-30] LTE1 to WIFI 2 -39 [-40] LTE2 to WFI 1 -39 [-40] LTE2 to WIFI 2 -34 [-32] WIFI 1 to WIFI 2 -74 [-70] GNSS to LTE 1 -68 [-68] GNSS to LTE 2 -43 [-43] GNSS to WIFI 1 -65 [-62] GNSS to WIFI 2 -68 [-66] Azimuth Plane 3 dB Beamwidth 360°, Omnidirectional Nominal Impedance (Ohms) 50 Polarization Linear Vertical Max Power-Ambient 25°C (W) 30 (LTE/CELL) /10 (WIFI) Notes: (*) – This parameter is based on a 30cm (1ft) cable length. For the ground plane measurement, a 30cm (1ft) ground plane was used (**) – This parameter is based on a 518cm (17ft) cable length. For the ground plane measurement, a 30cm (1ft) ground plane was used. Antenna specifications are subject to change according to the ground plane size
DATA AND DEVICES / VFP69383B22JN MECHANICAL SPECIFICATIONS Dimensions – LxWxH – mm (in.) 179 x 63 x 48 (7.04 x 2.48 x 1.69) Weight – kg (lbs.) 0.63 (1.4) Cable Type LMR 100, Black Mounting P-Mount Radome Material PC, UL94-V0 Baseplate Material Aluminum ENVIRONMENTAL SPECIFICATIONS Operating Environment Outdoor Vehicle Operating Temperature – °C (°F) -30 to +70°C (-22 to +158°F) Storage Temperature – °C (°F) -40 to +85°C (-40 to +185°F) Ingress Protection Rating IP67 Material Substance Compliance RoHS GNSS ANTENNA SPECIFICATIONS Frequency of Operation (MHz) 1559 - 1606 Band BEIDOU GPS GLONASS LNA Gain, Typ. @ room temp. (dBi) 26 27 26 Noise Figure @ room temp., Max (dB) 3.0 2.5 2.8 Max VSWR @ room temp. 2:1 2:1 2:1 Polarization RHCP Nominal Impedance (Ohms) 50 DC Voltage (Vdc) 3.3 Operating Supply Voltage (Vdc) 2.5 - 7.0 Current Consumption, Max @ room temp mA) 20 Out-of-band Signal Rejection Min @ room temp (dBc) 60 (@1-1525 MHz) 60 (@1675-2000 MHz) 50 (@2000-3000 MHz) Input Max Power (dBm) -30 Cable Type RG174 SAFETY The VFP69383B22JN and all associated equipment should be installed in accordance with all applicable local and national electrical code guidelines to ensure safe operation. APPLICATION The VFP69383B22JN antenna provides an excellent solution for Public Safety, Transportation and After Market Fleet applications with an integration of wide range of frequencies within one aerodynamic housing. This 5-port antenna is configured for 2x MIMO operation over 3G/4G/ISM/CBRS frequencies, 2x MIMO operation over both Low/High Band WiFi and 1x port that provides an active antenna for enabling GNSS global navigational services. LOCATION The antenna should be mounted on the desired location before connecting the cable. This is to ensure that the cable is not twisted or damage during the mounting of the antenna.
DATA AND DEVICES / VFP69383B22JN MOUNTING
- The mounting area should be clean of any debris, clear from obstructions and as flat as possible
- Punch or drill a 21 mm in the roof of the vehicle noting that a 300 mm clearance radius around the antenna is recommended
- The recommended orientation is facing the front of the vehicle with cables facing the rear: see illustration below
- Feed the cables from the bottom of the antenna through the topside of the 21 mm hole. Peel the adhesive covering on the bottom side of the antenna’s gasket. Place the threads of the antenna through the hole so that the gasket of the antenna is flat on the vehicle surface. Slide the lock-nut and washer around the 5 cables and finger- tighten to the stud of the antenna. Tighten the nut with a wrench using 30 Nm of torque
- Use a short service loop (slack) with tie-downs to secure the antenna cables such that any force or movement will not be transmitted to the antenna connectors or the apparatus. Minimum bending radius for the cable exiting the bottom of the antenna is 10 mm
te.com TE Connectivity, TE Connectivity (logo) and Every Connection Counts are trademarks. All other logos, products and/or company names referred to herein might be trademarks of their respective owners. The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application. TE warrants to the original end user customer of its products that its products are free from defects in material and workmanship. Subject to conditions and limitations TE will, at its option, either repair or replace any part of its products that prove defective because of improper workmanship or materials. This limited warranty is in force for the useful lifetime of the original end product into which the TE product is installed. Useful lifetime of the original end product may vary but is not to exceed five (5) years from the original date of the end product purchase. ©2021 TE Connectivity. All Rights Reserved. 12/21 Original USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico: +52 (0) 55-1106-0800 Latin/S. America: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 TE TECHNICAL SUPPORT CENTER External antenna is now part of DATA AND DEVICES / VFP69383B22JN