KQ0805T KOA | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 7
Technical content
Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. PAGE 1 OF 7 Chip Inductors Type KQ 0805 1. Scope of Application This specification shall be applied to chip inductors KQ series produced by KOA Corporation. KOA SPEER ELECTRONICS, INC. 3. Type Designation Type designation shall be as the following form. Size ToleranceNominal Inductance
0805 G: ±2%
J: ±5% K: ±10% M: ±20% 10N: 10nH R10: 0.1µH 1R0: 1.0µH
0805 J10N
TE: 7" Embossed Plastic TD: 7" Paper Tape TE Termination Material T: Sn (Other termination styles available, contact factory for options) TKQ Type New Type CERTIFIED CERTIFIED L h t d W2Magnetic Wire Flat Top Film Ceramic/ Ferrite Core Electrode Inner Coating LW 1 W 2 t h d Dimensions inches (mm) .079±.008 (2.0±0.2) .059±.008 (1.5±0.2) .018±.004 (0.45±0.1) .053±.004 (1.35±0.1) .051±.008 (1.3±0.2) .016±.006 (0.40±0.15)KQ0805 Size Code 2. Dimensions and Construction
5.1 Measurement Method
Inductance Range Test Equipment Fixture Setup Frequency 3.3 nH to 820 nH 4291A RF Impedance 16193A E.L = 1.4 cm Listed analyzer (H.P) Test fixture OSC = 500 mV Table-1 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. PAGE 2 OF 7 SS-193 R7 KOA SPEER ELECTRONICS, INC. 4. Standard Applications Part Designation L Measuring Frequency DC Resistance Maximum (Ω) Allowable DC Current Maximum (mA) Self Resonant Frequency Minimum (MHz) Q Quality Factor Minimum Q Measuring Frequency (MHz) Marking Nominal Inductance (nH) Inductance Tolerance 4 250 200 150 100 500 250 100 500 400 0.15 0.17 0.20 0.22 0.25 0.27 0.29 0.31 0.34 0.38 0.42 0.46 0.51 0.56 0.64 0.70 1.0 1.4 1.5 1.76 1.9 4000 3400 3300 2600 2500 2050 2000 1650 1450 1200 1100 870 920 850 650 600 560 375 340 2.2188 2.35215 1300 100 120 150 180 220 270 330 390 470 560 KQ0805TTE12N* KQ0805TTE15N* KQ0805TTE18N* KQ0805TTE22N* KQ0805TTE27N* KQ0805TTE33N* KQ0805TTE39N* KQ0805TTE47N* KQ0805TTE56N* KQ0805TTE68N* KQ0805TTE82N* KQ0805TTER10* KQ0805TTER12* KQ0805TTER15* KQ0805TTER18* KQ0805TTER22* KQ0805TTER27* KQ0805TTER33* KQ0805TTER39* KQ0805TTER47* KQ0805TTER56* 6804KQ0805TTER68* 8205KQ0805TTER82* 350 310 290 250 230 190 180 G:±2% J: ±5% K: ±10% M:±20% G:±2% J: ±5% K: ±10% J: ±5% K: ±10% 1550 1500 1000 50 600 0.08 0.11 0.12 6000 5500 4700 3.3 6.8 8.2 KQ0805TTE3N3* KQ0805TTE6N8* KQ0805TTE8N2* J: ±5% K: ±10% M:±20% * Add tolerance character (G, J, K, M) No. Item Specification
1 Storage temperature range -40°C ~ +100°C
2 Operating temperature range -40°C ~ +125°C
- Rating
Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. PAGE 3 OF 7 KOA SPEER ELECTRONICS, INC. 6. Test Conditions Unless otherwise specified, the test shall be performed at the temperature of 20±15°C and at a relative humidity of 65±20%. Reverse for the test conditions shall be performed at the temperature of 20±2°C and at a relative humidity of 65±5%. 7. Reliability Tests Item Requirement Test Methods Dielectric withstanding No evidence of flaming, 5 seconds at AC 500 V applied voltage fuming, or breakdown between both terminals and film. Insulation resistance 1000M Ω and over 1 minute at DC 100 V measured between both terminals and film. Flammability IEC 695-2-2 Withstands needle-flame test. Item Requirement Test Methods Terminal pull strength No evidence of damage Terminals shall withstand a pull of 10 N in a horizontal direction. Terminal bending No evidence of breakdown Specimen shall be soldered on bend strength test board and force applied to the opposite side to cause a 10 mm deflection Vibration ∆L/L within ±5% 2 hours in each direction of X, Y , Z, ∆Q/Q within ±10% on PCB at a frequency range of 10-55-10Hz with 1.5 mm amplitude Dropping No evidence of damage Dropping 1 m on the ground of ∆L/L within ±5% concrete 1 time ∆Q/Q within ±10% Resistance to No evidence of outer damage Immerse in the solder at 260±5°C soldering heat ∆L/L within ±5% for 10±1 seconds ∆Q/Q within ±10% Solderability 95% of the terminal should Immerse in the solder at 230±5°C be covered with new solder for 3±0.5 seconds Resistance to No damage and marking Accordance with MIL-STD-202F solvent must remain legible Method 215 7-2 Mechanical Characteristics
Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. PAGE 4 OF 7 SS-193 R7 Item Requirement Test Methods Low temperature No evidence of damage Store at -40±2°C, for 1000 hours storage ∆L/L within ±5% ∆Q/Q within ±10% High temperature No evidence of damage Store at +125±2°C, for 1000 hours storage ∆L/L within ±5% ∆Q/Q within ±10% Moisture endurance No evidence of damage Store at 40±2°C, 90~95% RH for ∆L/L within ±5% 1000 hours ∆Q/Q within ±10% Load life No evidence of damage Biased to full rated current at ∆L/L within ±5% +125°C for 1000 hours ∆Q/Q within ±10% High temperature No evidence of damage Biased to 10% rated current at High Humidity ∆L/L within ±5% +85°C, 85% RH for 1000 hours ∆Q/Q within ±10% Thermal shock No evidence of damage 100 cycles between ∆L/L within ±5% -40°C/hour and +125°C/hour ∆Q/Q within ±10% Temperature ∆L/L within ±5% ∆L/L to be measured at the characteristics temperature of between -40°C and +125°C as based on the inductance at 20°C 7-3 Environmental Characteristics Unless otherwise specified, measurements shall be performed within 2 hours after leaving test samples for more than one hour at the normal temperature and at the normal humidity. KOA SPEER ELECTRONICS, INC.
Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. PAGE 5 OF 7 (1) Dimensions of Carrier Tape 8. Packaging 8-1 Taping The tapes for taping shall be embossed carrier tapes of 8 mm width and 4 mm pitches. The standard quantity per reel shall be 2,000 pieces. KOA SPEER ELECTRONICS, INC. Feeding hole* øD0 AT2 T1 Chip inductor øD1 B P1 E F W Tape running direction Chip pocket Series A B W E F T1 3N3~R39 0.062 ± 0.003 0.087 ± 0.003 0.059 ± 0.003 (1.5 ± 0.1) Dimensions in inches (mm) Series T2 P0 P1 P2 øD0 øD1 3N3~R39 R47~R82 0.1 0.003 Dimensions in inches (mm) 0.2 0.007 * 20 Pitches accumulation of feeding holes shall be 80 ± 0.15 mm. Top tape peeling strength: 0.1N ~ 0.7N
Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. PAGE 6 OF 7 (2) Taped Configurations (conforming to EIA-481 standard) Dimensions in inches (mm) Drawing out direction End Beginning Leader spaceEmpty spaceChip mounting spaceEmpty space (3) Reel Dimensions and Indication The following items shall be indicated on the reel.
- Type (KQ 0805 TE)
- Nominal inductance and tolerance
- Quantity
- Production lot number
- Manufacturer’s name or trade mark Dimensions in inches (mm) 7.08 (180 ± )03 .354 (9.0 ± 0.3) Indicate position 2.36 (60 ± 1.0) .448 (11.4 ± 1.0) .079 (2.0 ± 0.5) .511 (13 ± 0.2) .826 (21 ± 0.8) KOA SPEER ELECTRONICS, INC.
Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. PAGE 7 OF 7 9. General Information (1) Storage Chip inductors shall not be stored under high temperature and high humidity conditions. Especially, do not store taping where they are exposed to heat or direct sunlight. Otherwise, the packing material may be deformed, causing problems during mounting. (2) Mounting Placement force should not be excessive. (3) Soldering Flow soldering should be done at 260°C for less than 10 seconds. Reflow soldering should be done at 240°C for less than 30 seconds. When using a soldering iron, temperature shall not exceed 350°C and within 3 seconds. Soldering iron time of each electrode shall be allowed only one time. After soldering, chip inductors shall not be stressed excessively. (4) Cleaning There is no problem using organic solvents. Since this chip inductor is a coil of ultra-fine wire, it is susceptible to vibration. If an ultrasonic cleaning unit is used for cleaning, check for any possibility of problem generation before practical use since such cleaning units considerably differ in vibration level and mode. Although the conditions differ depending on the printed board size, ultrasonic cleaning is generally used in the conditions described below as examples. Power: Within 20 W/L Cleaning times: Within 5 minutes (5) Pattern design The land pattern is recommended as follows. Dimensions in inches (mm) .110 (2.80) Inductor position.07 (1.78) .03 (0.76) .016 (0.40) Solder resist KOA SPEER ELECTRONICS, INC.