KQ0603T KOA | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. PAGE 1 OF 6 Chip Inductors Type KQ 0603 1. Scope of Application This specification applies to chip inductors KQ series produced by KOA corporation. 3. Type Designation Type designation shall be as the following form. KOA SPEER ELECTRONICS, INC. Size ToleranceNominal Inductance

0603 G: ±2%

J: ±5% K: ±10% 10N: 10nH R10: 0.1µH 1R0: 1.0µH

0603 J10N

TE: 7" Embossed Plastic TD: 7" Paper Tape TE Termination Material T: Sn (Other termination styles available, contact factory for options) TKQ Type New Type L h t d W2Magnetic Wire Flat Top Film Ceramic/Ferrite Core Electrode Inner Coating LW 1 W 2 t h d Dimensions inches (mm) .063±.004 (1.6±0.1) .039±.004 (1.0±0.1) .014±.004 (0.35±0.1) .033±.004 (0.85±0.1) .035±.004 (0.9±0.1) .01±.006 (0.25±0.15)0603 Size Code 2. Dimensions and Construction CERTIFIED CERTIFIED

Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. PAGE 2 OF 6 SS-214 R8 KOA SPEER ELECTRONICS, INC. 4. Standard Applications Part Designation L Measuring Frequency DC Resistance Maximum (Ω) Allowable DC Current Maximum (mA) Self Resonant Frequency Minimum (MHz) Q Quality Factor Minimum Q Measuring Frequency (MHz) Marking Nominal Inductance (nH) Inductance Tolerance 200 150 150 100 100 200 400 300 140 280 120 170 100 0.31 0.34 0.49 0.54 0.58 0.61 0.65 0.92 2.2 2.5 2.3 3.0 3.7 1900 1700 1400 1350 1300 1400 1300 1200 900 800 700 100 110 120 150 180 220 270 330 390 KQ0603TTE47N* KQ0603TTE56N* KQ0603TTE68N* KQ0603TTE72N* KQ0603TTE82N* KQ0603TTER10* KQ0603TTER11* KQ0603TTER12* KQ0603TTER15* KQ0603TTER18* KQ0603TTER22* KQ0603TTER27* KQ0603TTER33* KQ0603TTER39* * Add tolerance character (G, J, K) 250 250 700 600 0.03 0.045 0.063 0.08 0.063 0.116 0.11 0.106 0.109 0.13 0.086 0.13 0.17 0.104 0.17 0.19 0.135 0.22 0.144 12500 6900 5900 5800 4800 4800 4000 3300 3100 3000 2650 2800 2250 4600 1.6 1.8 3.6 3.9 4.3 4.7 6.8 7.5 8.7 C E F G H J K L M N KQ0603TTE1N6* KQ0603TTE1N8* KQ0603TTE3N6* KQ0603TTE3N9* KQ0603TTE4N3* KQ0603TTE4N7* KQ0603TTE6N8* KQ0603TTE7N5* KQ0603TTE8N7* KQ0603TTE10N* KQ0603TTE11N* KQ0603TTE12N* KQ0603TTE15N* KQ0603TTE16N* KQ0603TTE18N* KQ0603TTE22N* KQ0603TTE24N* KQ0603TTE27N* KQ0603TTE30N* J: ±5% K: ±10% G: ±2% J: ±5% K: ±10% P Q 2300 0.22 0.25 0.28 2080 2200 2000 KQ0603TTE33N* KQ0603TTE36N* KQ0603TTE39N* KQ0603TTE43N* 3.3XKQ0603TTE3N3* 0.055 5.1YKQ0603TTE5N1* 0.115 8.2AKQ0603TTE8N2* 0.12 9.5BKQ0603TTE9N5* 0.125 23SKQ0603TTE23N* 0.152700 T5 1KQ0603TTE51N* 0.30 U 200KQ0603TTER20* 2.3 130V 210KQ0603TTER21* W 250KQ0603TTER25* 2.41000 5 1901.21640470KQ0603TTER47* 50 506 1302.09560560KQ0603TTER56* J: ±5% K: ±10% NEW

Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. PAGE 3 OF 6 KOA SPEER ELECTRONICS, INC. 6. Test Conditions Unless otherwise specified, the test shall be performed at the temperature of 20 ± 15°C and at a relative humidity of 65 ± 20%. Reverse test conditions shall be performed at the temperature of 20 ± 2°C and at a relative humidity of 65 ± 5%.

5.1 Measurement Method

Nominal Inductance Measuring Range Test Equipment Fixture Setup Frequency 1.6 nH to 1200 nH 4291A RF 16193A E.L = 1.4 cm Listed Impedance analyzer Test fixture OSC = 500 mV Table-1 7. Reliability Tests Item Requirement Test Methods Dielectric withstanding No evidence of flaming, 5 seconds at AC 500 V applied voltage fuming, or breakdown between both terminals and film. Insulation resistance 1000M Ω and over 1 minute at DC 100 V measured between both terminals and film. Flammability IEC 695-2-2 Withstands needle-flame test.

7.1 Electrical Characteristics

L Measuring Frequency DC Resistance Maximum (Ω) Allowable DC Current Maximum (mA) Self Resonant Frequency Minimum (MHz) Q Quality Factor Minimum Q Measuring Frequency (MHz) Marking Nominal Inductance (nH) Inductance Tolerance 7 1401.97540680KQ0603TTER68* 50 50 8 1103.09490820KQ0603TTER82* J: ±5% K: ±10% 309 905.134401000KQ0603TTE1R0* 0 805.454001200KQ0603TTE1R2* NEW 4. Standard Applications (continued) Item Specification Storage temperature range -40°C ~ +100°C Operating temperature range -40°C ~ +125°C 5. Rating

Item Requirement Test Methods Low temperature No evidence of damage Store at -40 ± 2°C, for 1000 hours storage ∆L/L within ± 5% ∆Q/Q within ± 10% High temperature No evidence of damage Store at +125 ± 2°C, for 1000 hours storage ∆L/L within ± 5% ∆Q/Q within ± 10% Moisture endurance No evidence of damage Store at 40 ± 2°C, 90 ~ 95% RH ∆L/L within ± 5% for 1000 hours ∆Q/Q within ± 10% Load life No evidence of damage Biased to full rated current at ∆L/L within ± 5% +125°C for 1000 hours ∆Q/Q within ± 10%

7.3 Environmental Characteristics

Unless otherwise specified, measurements shall be performed within 2 hours after leaving test samples for more than one hour at the normal temperature and at the normal humidity. Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. PAGE 4 OF 6 SS-214 R8

7.2 Mechanical Characteristics

KOA SPEER ELECTRONICS, INC. Item Requirement Test Methods Terminal pull strength No evidence of damage Terminals shall withstand a pull of 5 N in a horizontal direction. Terminal bending No evidence of breakdown Specimen shall be soldered on bend strength test board and force applied to the opposite side to cause a 3 mm deflection Vibration ∆L/L within ± 5% 2 hours in each direction of X, Y , Z, ∆Q/Q within ± 10% on PCB at a frequency range of 10-55-10Hz with 1.5 mm amplitude Dropping No evidence of damage Dropping 1 m on the ground of ∆L/L within ± 5% concrete 1 time ∆Q/Q within ± 10% Resistance to No evidence of outer damage Immerse in the solder at 260 ± 5°C soldering heat ∆L/L within ± 5% for 10±1 seconds ∆Q/Q within ± 10% Solderability 95% of the terminal should Immerse in the solder at 230 ± 5°C be covered with new solder for 3 ± 0.5 seconds Resistance to No damage and marking Accordance with MIL-STD-202F solvent must remain legible Method 215

Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. PAGE 5 OF 6 8. Packaging

8.1 Taping

The tapes for taping shall be embossed carrier tapes of .315" (8 mm) width and .157" (4 mm) pitches. The standard quantity per reel shall be 2,000 pieces. KOA SPEER ELECTRONICS, INC. .059 (1.5 ± )0.1 Dimensions in inches (mm) * 10 Pitches accumulation of feeding holes shall be 1.57" (40 ± 0.2 mm). Top tape peeling strength: 0.1 N ~ 0.7N Feeding hole* Chip inductor Chip pocket Tape running direction .010 (0.25 ± 0.05) .047 (1.2 ± 0.1) .043 (1.1 ± 0.05) .079 (2.0 ± 0.05) .157 (4.0 ± 0.1) .157 (4.0 ± 0.1) .069 (1.75 ± 0.1) .024 (0.6 ± 0.05) .069 (1.75 ± 0.1) .138 (3.5 ± 0.05) .315 (8.0 ± 0.1) (1) Dimensions of Carrier Tape (2) Taped Configurations (conforming to EIA-481 standard) Dimensions in inches (mm) Drawing out direction End Beginning Leader spaceEmpty spaceChip mounting spaceEmpty space Item Requirement Test Methods High temperature No evidence of damage Biased to 10% rated current at High humidity ∆L/L within ± 5% +85°C, 85% RH for 1000 hours ∆Q/Q within ± 10% Thermal shock No evidence of damage 100 cycles between ∆L/L within ± 5% -40°C/hour and +125°C/hour ∆Q/Q within ± 10% Temperature ∆L/L within ± 5% ∆L/L to be measured at the characteristics temperature of between -40°C and +125°C as based on the inductance at 20°C

7.3 Environmental Characteristics (continued)

Unless otherwise specified, measurements shall be performed within 2 hours after leaving test samples for more than one hour at the normal temperature and at the normal humidity.

  1. General Information (1) Storage Chip inductors shall not be stored under high temperature and high humidity conditions. Especially, do not store taping where they are exposed to heat or direct sunlight. Otherwise, the packing material may be deformed, causing problems during mounting. (2) Mounting Placement force should not be excessive. (3) Soldering Flow soldering should be done at 260°C for less than 10 seconds. Reflow soldering should be done at 240°C for less than 30 seconds. When using a soldering iron, temperature shall not exceed 350°C and within 3 seconds. Soldering iron time of each electrode shall be allowed only one time. After soldering, chip inductors shall not be stressed excessively. (4) Cleaning It is no problem to use organic solvents. Since this chip inductor is a coil of ultra-fine wire, it is susceptible to vibration. If an ultra-sonic cleaning unit is used for cleaning, check for any possibility of problem generation before practical use since such cleaning units considerably differ in vibration level and mode. Although the conditions differ depending on the printed board size, ultrasonic cleaning is generally used in the conditions described below as examples. Power: Within 20 W/L Cleaning times: Within 5 minutes (5) Pattern design The land pattern is recommended as follows. Dimensions in inches (mm) .076 (1.92) Inductor position.040 (1.02) .025 (0.64) .006 (0.16) Solder resist SS-214 R8 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. PAGE 6 OF 6 (3) Reel Dimensions and Indication The following items shall be indicated on the reel.
  • Type (KQ 0603 TE)
  • Nominal inductance and tolerance
  • Quantity
  • Production lot number
  • Manufacturer’s name or trade mark Dimensions in inches (mm) 7.08 (180 )+0-3 .354 (9.0 ± 0.3) Indicate position 2.36 (60 ± 1.0) .448 (11.4 ± 1.0) .079 (2.0 ± 0.5) .511 (13 ± 0.2) .826 (21 ± 0.8) KOA SPEER ELECTRONICS, INC.