KPEG110 ETC2 | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

志豐電子股份有限公司KINGSTATE ELECTRONICS CORP 2/5 KPEG110 A.SCOPE 範疇 This specification applies piezo audio transducer, KPEG110 此規格書適用於壓電式蜂鳴器KPEG110 B. SPECIFICATION 規格 No. Item Unit Specification Condition 1 Operating Volt. 操作電壓 Vp-p MAX 30

2 Current consumption

消耗電流 mA MAX 12 at 10Vp-p, square wave,4.1KHz.

3 Sound pressure level

輸出音壓 dB MIN 90 at 10cm/10Vp-p,square wave,4.1KHz.

4 Electrostatic capacity

靜電容量 pF 25,000±30% - at 1KHz/1V 5 Operating temp. 操作溫度 ºC -30 ~ +85 6 Storage temp. 儲存溫度 ºC -40 ~ +95

7 Dimension

尺寸 mm ψ24.0x H5.0 See appearance drawing 請參照外觀尺寸圖

8 Weight (MAX)

重量 gram 2.2

9 Material

材質 ABS UL-94 1/16” HB HIGH HEAT （BLACK）

10 Terminal

端子 Wire type See appearance drawing 請參照外觀尺寸圖 Environmental Protection Regulation 環保法規 ROHS C. APPEARANCE DRAWING 外觀尺寸圖 Black Red KPEG110 KINGSTATE UL1571LF 30AWG Tol : ± 0.5 Unit : mm

志豐電子股份有限公司KINGSTATE ELECTRONICS CORP 3/5 KPEG110 D. TYPICAL FREQUENCY RESPONSE CURVE 頻率響應曲線 E. MEASURING METHOD 測量方法 S.P.L. Measuring Circuit 音壓測試接線圖 Input Signal: 10Vp-p,4.1kHz, Square Wave 輸入信號: 10Vp-p,4.1kHz,方波 Mic : RION S.P .L meter UC30 or equivalent Mic : RION噪音計 UC30 或同等品 S.G : Hewlett Packard 33120A Function Generator or equivalent S.G : Hewlett Packard 33120A 函數信號產生器 或同等品

志豐電子股份有限公司KINGSTATE ELECTRONICS CORP 4/5 KPEG110 F. MECHANICAL CHARACTERISTICS 機械特性 No Item Test Condition Evaluation standard

1 Solderability

焊鍚附著性 Stripped wires of lead wires are immersed in rosin for 5 seconds and then immersed in solder bath of +230 ±5 ℃ for 3 ±0.5 seconds. 裸線部份浸入松香溶液5 秒後,再浸入+230 ±5 ℃溶融焊鍚槽中3 ±0.5 90% min. stripped wires shall be wet with solder.(Except the edge of terminal) 浸入裸線部份附著焊鍚90%以 上.(末端斷面不算) Soldering Heat Resistance 焊鍚耐熱性 Stripped wires are immersed up to 1.5mm from insulation in solder bath of +300 ±5 ℃ for 3 ±0.5 seconds or +260 ±5 ℃ for 10 ±1 seconds, and then sounder shall be measured after being placed in natural condition for 4 hours. 距絕緣體1.5mm的位置,浸入+300 ±5 ℃ 的焊鍚槽 3 ±0.5 秒,或+260± 5 ℃ 的焊鍚槽 10 ±1 秒. No interference in operation 操作上無任何不良 Lead Wire Pull Strength 線材拉力 The pull force shall be applied to lead wire : Horizontal 3.0N Vertical 2.0N 線材垂直方向施以3.0N的力量, 水平方向施以2.0N的力量. No damage and cutting off. 線材不鬆動,不脫落.

4 Vibration

振動試驗 Buzzer shall be measured after being applied vibration of amplitude of 1.5mm with 10 to 55hz band of vibration frequency to each of 3 per-pendicular directions for 2 hours. 振動週波數10～55HZ、全振幅 1.5mm於 X.Y.Z 3個方向,各2 小時

5 Drop test

落下測試 The part only shall be dropped from a height of 75cm onto a 40mm thick wooden board 3 times in 3 axes (X.Y.Z). (a total of 9 times). 單體從75公分高處, X.Y.Z.3個方向,各3 回,落於40mm厚木板上. The value of oscillation frequency/ current consumption should be in ±10% compared with initial ones .The SPL should be in ±10dB compared with initial one. 諧振頻率與消耗電流變化量須在 ±10%內. 輸出音壓變化量須在± 10dB內. G. ENVIRONMENT TEST 環境測試 No Item Test Condition Evaluation standard 1 High temp. test 高溫測試 After being placed in a chamber at +95 ℃ for 240 hours 置於+95 ℃環境中240小時 2 Low temp. test 低溫測試 After being placed in a chamber with –40 ℃ for 240 hours 置於-40 ℃ 環境中240小時

3 Humidity test

相對濕度測試 After being placed in a chamber at +40 ℃ and 90±5% relative humidity for 240 hours 置於+40 ℃, 相對濕度 90±5% 環境中240小時 4 Temp. cycle test 溫度循環試驗 The part shall be subjected to 5 cycles. One cycle shall be consist of:: 單體承受溫度循環測試5 次,其循環內容如圖示: + 9 5 ℃ + ２５℃ + ２５℃ - 4 0 ℃ 3hours Being placed for 4 hours at +25 ℃, buzzer shall be measured. The value of oscillation frequency/ current consumption should be in ±10% compared with initial ones .The SPL should be in ±10dB compared with initial one. 經測試後, 靜置於+２５℃（室 溫）環境中4 小時後 ,諧振頻率與 消耗電流變化量須在±10%內. 輸出音壓變化量須在±10dB內.

志豐電子股份有限公司KINGSTATE ELECTRONICS CORP 5/5 KPEG110 H. RELIABILITY TEST 信賴性測試 No. Item Test condition Evaluation standard Operating life test 壽命測試 1.Continuous life test高溫壽命測試(連續) 48 hours continuous operation at +70 ℃ with rated voltage applied. 在+70 ℃環境下,以額定電壓連續操作48小時 2.Intermittent life test 室溫壽命測試(間歇) A duty cycle of 1 minute on, 1 minutes off, a minimum of 5000 times at room temp.( +25 ±2℃)and rated voltage applied 在室溫下(+25 ±2℃), 以額定電壓操作, 通電1 分鐘/斷電1 分鐘,測試 5000次循環. Being placed for 4 hours at +25 ℃ , buzzer shall be measured. The value of oscillation frequency/ current consumption should be in ±10% compared with initial ones .The SPL should be in ±10dB compared with initial one. 經測試後, 靜置於+２５℃（室 溫）環境中4 小時後,諧振頻率 與消耗電流變化量須在±10% 內. 輸出音壓變化量須在± 10dB內. TEST CONDITION. Standard Test Condition : a) Temperature : +5 ~ +35ºC b) Humidity : 45-85% c) Pressure : 860-1060mpa 一般測試條件 : a) 溫度 : +5 ~ +35ºC b) 濕度 : 45-85% c) 氣壓 : 860-1060mpa Judgement Test Condition : a) Temperature : +25 ± 2ºC b) Humidity : 60-70% c) Pressure : 860-1060mpa. 爭議時測試條件 : a ) 溫度 : +25 ± 2ºC b) 濕度 : 60-70% c) 氣壓 : 860-1060mpa I. PACKING STANDARD 包裝規格 330mm 10x50PCS=500PCS 500PCSX10=5,000PCS Out Box Carton Box 310mmx248mmx49mm 550mmx330mmx290mm 550mm 290mm (10PCS Out Box) Carton Box Out Box Out Box 10x50PCS=500PCS