KPC6N135 COSMO | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
J cosmo KPC6N135 Features Outside Dimension:Unit (mm 1. High speed response t , ten. pun (MAX.1.5us at Ri=4.1k 2) qf h oe 2. High common mode reiection voltage q P ata Code (CM:TYP.1kV/us) ; b Ox 3. Standard dual-in-line package ve Applications =| Col 1. Computers,measuring instruments,control equipment. 2. High speed line receivers high speed logic. ie |\\ moat | te 3. Telephone sets. ne a Tolerance:s0.2 mm 4. Signal transmission between circuits of different potentials and impedances. . . Schematic:Top View e768 5 a cL 3. Cathode a.NC 5. GND 8.Vo To 8. Vee 723 4 Absolute Maximum Ratings (re-25%) [_Forwardcurent | te | Tm [Peak forward curent | te fm [Peak transient forwardcurent | tw | A [Reverse votage || SSCSSC‘C*d | Suppyvoiage SSSSSCSCS*dSCC CI [Ouputvotage——SSSCSCSCS~S~—SCSCi‘iNOS SSO | Ennerteereesewhaandvege nsw?) | veo [Ss SSSSSCSCSSCSC‘NCSC* [Average outputcurent |S )SSSCBTSSTS~SSSS mA | Peak outputcurent | top || mA Base current (Pin7) es | Powerdissipation | Po | tm [Isolation voltage Tminute [iso | 2500 | Vm [___*Soldering temperature | Tso =| | "1 50% duty cycle, Pulse width : 1mS. Decreases at the rate of 1.6mA/'C if the external temperature is 70°C or more. *2 Pulse width<=1uS,300pulse/sec *3 40 to 60% RH,AC for 1 minute *4 For 10 seconds A115 © 2005-2006 COSMO ELECTRONICS CORPORATION hhttpy/Avww.cosmo-ic.com
Electro-optical Characteristics (Ta=0 to +70°C unless otherwise specified ) [Parameter | Symbol | Conditions | MIN, | TYP. [ MAX. | Unit | cre | TH 250. Ir=16mA 7 ** Current transfer ratio Vo = 0.4V,, Voc = 4.5V IF=16mA Logic (0) output volage [Vou fPVoc = 4.5V,1_F=16mA | = | ot [oa | Ta=25C, |F=0 Vo = Voo = 5.5V Logic (1) output current lone Ta'=25C, |F=0 On) | Vo=Voo= 15V | Ton@) | Vec=Vo=tevir=o | = | TA IF=16mA [| acer vesntn || ee |e | Logic (1) supply current w= open, Vee = 18 eer | inputforward voltage |e Tae abc, Ir=tmA | Tt | 98 | Input forward vo! [| Tnputreverse voltage | BAR| Ta=25,_In=10UA [so fT \\VF=0 , f=1MHz a 7 | eak current(input-output) Ta=25C , 45% RH Vi0=3kVDC , t= 5s.
7 Capacitance(input-output) IMR, a
‘Transistor current = = ee ee
3 Current transfer rao is the ratio of input current and output current expressed in %
*6lo=1.4 *7 Measured as 2-pin element (Short 1,2,3,4 and 5,6,7,8) Switching Characteristics (Ta=25%GVoo=5V,1 =H6mA) [Parameter | Symbol | Conditions| MIN, | Typ. | MAX. | Unit | Propagation delay time = ° t = 4, Output (1}->(0) ra | Rerana “3 Propagation delay time 3 eon Se F° Instantaneous common mode rejection voltage 1F=0,V c=MIOV pp vius “Output (1)" {19 Instantaneous common mode rejection voltage cM. 1 F=16MA,VoM=10Vp-p_ -1000 ViuS “Output (0)" a "8 Re4.1kQ is equivalent to one LSTTL and 6.1kQ pull-up resistor. *10 Instantaneous common mode rejection voltage “output(1)" represents a. common mode voltage variation that can hold the output above (1) level (Vo > 2.0V) Instantaneous common mode rejection voltage “output(0)" represents a. common mode voltage variation that can hold the output above (0) level (Vo < 0.8V) "12 Bandwidth represents a point where AC input gose down by 34. © 2005-2006 COSMO ELECTRONICS CORPORATION A116 http:/Avww.cosmo-ic.com
*9 Tset Circuit Propagation Delay Time Pulse input Duty ratio ~e : jf _— el © Veo 0 ay a ol | ~ ow | Irmonitor o- ig Ch Ter 1v 1 1000: ten teu “11 Tset Circuit for Instantaneous Common Mode Rejection Voltage 1 — — — Faa% 10% ia {a} © Veosv H «_| a ws a4 Re ~ a ¥| tet . A (pom rn Or - om, A on ve a@ NOT et6mA A117 © 2005-2006 COSMO ELECTRONICS CORPORATION http:/www.cosmo-lc.com