KPA-3010F3C KINGBRIGHT | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 5
Technical content
Features
z 3.0mmx2.0mmx1.0mm right angle SMD LED, 1.0mm thickness. z Mechanically and spectrally matched to phototransistor. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. z Tinned pads for improved solderability. z RoHS compliant. Kingbright
SPEC NO: DSAA1131 REV NO: V.17A DATE: JUL/02/2016 PAGE: 2 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: F.Zhang ERP: 1203000562 Selection Guide Absolute Maximum Ratings at TA=25°C Electrical / Optical Characteristics at TA=25°C Part No. Emitting Color (Material) Lens Type Po (mW/sr) [2] @ 20mA Viewing Angle [1] Min. Typ. 2 θ1/2 Infrared (GaAs) Water Clear 1.2 3 160° *0.8 *2 KPA-3010F3C Parameter P/N Symbol Typ. Max. Units Test Conditions Forward Voltage [1] F3 V F 1.2 1.6 V I F=20mA Reverse Current F3 I R 10 uA V R = 5V Capacitance F3 C 90 pF V F=0V;f=1MHz Peak Spectral Wavelength F3 λP 940 nm I F=20mA Spectral Bandwidth F3 Δλ1/2 50 nm I F=20mA Parameter Symbol Values Units Power dissipation P D 80 mW DC Forward Current I F 50 mA Peak Forward Current [1] i FS 1.2 A Reverse Voltage V R 5 V Operating Temperature T A -40 To +85 °C Storage Temperature T STG -40 To +85 °C Notes: 1. 1/100 Duty Cycle, 10μs Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. Notes: 1.Forward Voltage: +/-0.1V. 2.Wavelength value is traceable to CIE127-2007 standards. 3.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Radiant Intensity / luminous flux: +/-15%. * Radiant intensity value is traceable to CIE127-2007 standards. Kingbright
SPEC NO: DSAA1131 REV NO: V.17A DATE: JUL/02/2016 PAGE: 3 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: F.Zhang ERP: 1203000562 KPA-3010F3C Kingbright
SPEC NO: DSAA1131 REV NO: V.17A DATE: JUL/02/2016 PAGE: 4 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: F.Zhang ERP: 1203000562 KPA-3010F3C Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Specifications (Units : mm) Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Kingbright
SPEC NO: DSAA1131 REV NO: V.17A DATE: JUL/02/2016 PAGE: 5 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: F.Zhang ERP: 1203000562 Terms and conditions for the usage of this document 1. The information included in this docum ent reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the dat asheet. If customer usage exceeds the spec ified limits, Kingbright will not be respon sible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applicati ons. If customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.kingbright.com/application_notes PACKING & LABEL SPECIFICATIONS KPA-3010F3C Kingbright