KP0215ANBKG036G

KP0215ANBKG036B-2SJB NKK | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 5

Technical content

Series KPSingle Color Illuminated Pushbutton www.nkkswitches.com General Specifications Electrical Capacity (Resistive Load) Low Level: 100mA maximum @ 12V DC Other Ratings Contact Resistance: 200 milliohms maximum Insulation Resistance: 100 megohms minimum @ 250V DC Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum 1,500V AC minimum between contacts & case for 1 minute minimum Mechanical Life: 5,000,000 operations minimum Electrical Life: 5,000,000 operations minimum Nominal Operating Force: 1.6N maximum (at center of cap) Materials & Finishes Plunger/Upper Housing: Polyacetal Lower Housing: Glass fiber reinforced PBT (UL94V-0) Movable Contact: Stainless steel with gold plating Stationary Contacts: Gold over copper alloy Switch Terminals: Brass with tin plating Environmental Data Operating Temperature Range: –25°C through +50°C (–13°F through +122°F) Humidity: 90 – 95% humidity for 240 hours @ 40°C (104°F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours Shock: 51G (500m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Cap Installation Force: 50.0N maximum downward force on actuator PCB Processing Soldering: Wave Soldering. Preheat temperature: 110°C @ 40 seconds; Peak temperature: 270°C @ 6 seconds; Cycles: 2 Manual Soldering. 390°C @ 4 seconds; Cycles: 2 Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL94V-0 lower housing The KP Series pushbuttons have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. Distinctive Characteristics KP Series’ latest offering in single color super bright white, yellow or blue LEDs with 2-pin termination. Ideal solution for a variety of control panel compositions. Shorter stroke of .138” (3.5mm). Nontactile actuation underlined with smooth, silent operation. Compact design with height of .906” (23.0mm) from PC board to top of cap (same height as programmable SmartSwitch®). Flat, sculptured or home key square caps in two common sizes for design flexibility in various applications. Twin contacts with gold plating assure high reliability and long life of 5,000,000 operations minimum. Custom legends available. Actual Size 05/02/19

Series KP Single Color Illuminated Pushbutton www.nkkswitches.com N Pole & Circuit 15A SPST OFF (ON) ( ) = Momentary Normally Open Contacts Contacts & Terminals G03 Gold Contacts and Straight PC Terminals; 100mA @ 12V DC 15A B G03K Housing K Black Only KP 02 Travel & Force 02 Stroke: 3.5mm (.138”) Actuation Force: 1.6N Super Bright LEDs 6B White 6E Yellow 6G Blue TYPICAL SWITCH ORDERING EXAMPLE 11.6mm Plunger and 15.0mm Sculptured Cap Clear Lens and White Diffuser SPST OFF-Momentary ON Circuit Normally Open Contacts DESCRIPTION FOR TYPICAL ORDERING EXAMPLE KP0215ANBKG036B-2SJB Black Housing Gold Contacts with 100mA RatingStraight PC Terminals Nontactile Actuation 6BN15A B G03K Plunger B 11.6mm Plunger for 15.0mm & 17.4mm Caps Cap Types F Flat S Sculptured T Home Key KP 02 Cap Sizes 2 15.0mm Square 3 17.4mm Square Cap Color JB Clear Lens & White Diffuser JB Actuation N Nontactile Super Bright White LED with 2 Pins

Series KPSingle Color Illuminated Pushbutton www.nkkswitches.com CAP TYPES & COLORS AT3084 Flat Cap F AT3079 Sculptured Cap S AT3087 Home Key Cap T AT3085 Flat Cap AT3080 Sculptured CapS AT3088 Home Key Cap T 2 15.0mm Square F 3 17.4mm Square (7.0) .276 (15.0) Sq .591 (7.0) .276 (17.4) Sq .685 (7.0) .276 (17.4) Sq .685 (7.0) .276 (15.0) Sq .591 (2.6) Dia .102 (7.0) .276 (17.4) Sq .685 (2.6) Dia .102 (7.0) .276 (15.0) Sq .591 ACTUATION Gold Contacts Straight PC Terminals 100mA @ 12V DC G03Black OnlyK N Nontactile HOUSING CONTACTS, TERMINALS, & RATING Plunger Position ( ) = Momentary Connected Terminals Throw & Switch Schematic Pole Model Normal Down Normal Down Note: Switch terminals “1” & “1a” are actually marked on the switch. SP KP0215A OFF (ON) Normally Open 1-1a SPST POLE & CIRCUIT 1 (COM) PLUNGER 11.6mm Plunger for 15.0mm & 17.4mm Caps B 11.6mm Plunger has a wide neck, easily holding either the 15.0mm or the 17.4mm Caps. (11.6) .457 (6.4) .252 Clear Lens White Diffuser JB Lens & Diffuser Colors Available: Materials & Finishes: Lens - Polycarbonate with glossy finish Diffuser - Polycarbonate with textured finish Optional Protective Guard AT4170 available; contact factory. Clear/White

Series KP Single Color Illuminated Pushbutton www.nkkswitches.com SUPER BRIGHT LED SPECIFICATIONS 15.0mm Square Cap with Yellow LED 17.4mm Square Cap with Blue LED KP0215ANBKG036E-2SJB KP0215ANBKG036G-3SJB The electrical specifications shown are determined at a basic temperature of 25°C. LEDs are an integral part of the switch and not available separately. LED circuit is isolated and requires an external power source. TYPICAL SWITCH DIMENSIONS ATTENTION ELECTROSTATIC SENSITIVE DEVICES (+) (-) (15.0) Sq .591 Part No. This Side (7.0) .276 (3.6) .142 (11.5) .453 (4.5) .177 (23.0) .906 (6.0) .236 (1.1) .043 (6.4) .252 (0.3) .012 (4.5) .177 (12.7) .500 (0.5) Sq Typ .020 (7.62) .300 (0.6) Typ .024 (12.7) .500 (15.0) Sq .591 L1L2 (2.54) .100 – + 0.5 (12.7) .500 (0.9) Dia Typ .035 (0.8) Dia Typ .031 (1.3) Dia Typ .051 (7.62) .300 (4.5) .177 (12.7) .500 (1.27) Typ .050 (12.7) .500 L2L1 1 1a (17.4) Sq .685 Part No. This Side (7.0) .276 (3.6) .142 (11.5) .453 (4.5) .177 (23.0) .906 (6.0) .236 (1.1) .043 (6.4) .252 (0.3) .012 (4.5) .177 (12.7) .500 (0.5) Sq Typ .020 (7.62) .300 (0.6) Typ .024 (12.7) .500 (15.0) Sq .591 L1L2 (2.54) .100 – + 0.5 (12.7) .500 (0.9) Dia Typ .035 (0.8) Dia Typ .031 (1.3) Dia Typ .051 (7.62) .300 (4.5) .177 (12.7) .500 (1.27) Typ .050 (12.7) .500 L2L1 1 1a White Yellow Blue If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula shown here. Maximum Forward Current IFM 30mA 30mA 30mA Typical Forward Current IF 20mA 20mA 20mA Forward Voltage VF 3.2V 3.2V 3.2V Maximum Reverse Voltage VRM 5V 5V 5V Current Reduction Rate Above 30°C ∆IF 0.45mA/°C .045mA/°C .045mA/°C Ambient Temperature Range –25 ~ +50°C –25 ~ +50°C –25 ~ +50°C 6E6B 6G R = E – VF IF Where: R E VF IF = Resistor Value (Ohms) = Source Voltage (V) = Forward Voltage (V) = Forward Current (A) VF I FR + E Anode Cathode

Series KPSingle Color Illuminated Pushbutton www.nkkswitches.com LEGENDS Lens Film Insert Diffuser STOP (13.0) Dia .512 (11.48) Dia .452 (0.76) Typ .030 (15.3) Dia .602 (0.76) Typ .030 (13.77) Dia .542 (12.8) Sq .504 (11.28) Dia .444 (0.76) Typ .030 (0.5) R .020 Sculptured Cap Lens Sculptured Cap Film Inserts Flat Cap Lens Flat Cap Film Inserts (12.8) Sq .504 (11.28) Sq .444 (0.76) Typ .030 (0.5) R .020 (13.4) Sq .528 (11.88) Dia .468 (0.76) Typ .030 (0.5) R .020 (15.0) Sq .591 (12.8) Sq .504 (17.4) Sq .685 (13.4) Sq .528 Printing on Diffuser is not advisable. Recommended Methods: Laser Etch on clear lens, Screen Print, or Pad Print on lens. Laser Print on film insert. Epoxy based ink is recommended. Film Insert Material and Thickness: Clear Polyester; 4 mil (100µ) maximum thickness (13.4) Sq .528 (11.88) Dia .468 (0.76) Typ .030 (0.5) R .020 NKK Switches can provide custom legends for caps. Contact factory for more information. Suggested Printable Areas for KP Lens Shaded areas are suggested printable areas for Film Insert. Suggested Printable Areas for KP Film Insert Shaded areas are suggested printable areas for Lens. ASSEMBLY INSTRUCTIONS FOR SQUARE CAPS As shown in the accompanying illustration, the cap and plunger are designed with tabs and notches to assure proper orientation of the cap on the switch. Holding the switch tightly, pull the cap off the switch. Once the cap assembly is released from the plunger, the lens and diffuser can be separated. Pry up the lens with fingernail or flat tip screwdriver inserted at the step on the diffuser. After aligning notches with tabs, join the lens and diffuser. Hold the switch tightly without touching the terminals. Firmly press the cap onto the plunger by applying pressure from one side to the other until both are snapped together. Cap Orientation Notch Tab Step Plunger Notches Cap Assembly Plunger Switch ATTENTION ELECTROSTATIC SENSITIVE DEVICES Removal of Cap Assembly & Separation of Lens & Diffuser Installation or Replacement of Cap