KP0215ANBKG03

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 12

Technical content

Series KP Miniature Audio/Video Pushbuttons D36 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons DIlluminated PBSlides Programmable RockersTouch Tilt Toggles www.nkkswitches.com General Specifications Electrical Capacity (Resistive Load) Low Level: 100mA maximum @ 12V DC Other Ratings Contact Resistance: 200 milliohms maximum Insulation Resistance: 100 megohms minimum @ 250V DC Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum 1,500V AC minimum between contacts & case for 1 minute minimum Mechanical Life: 5,000,000 operations minimum; 1,000,000 operations minimum for custom Rectangular Switch/Cap Assembly (at center of cap) Electrical Life: 5,000,000 operations minimum Nominal Operating Force: KP01: 1.9N maximum for Tactile & Nontactile models (at center of cap) KP02: 1.6N maximum for Tactile, Nontactile & Tactile/Audible models (at center of cap) Materials & Finishes Plunger/Upper Housing: Polyacetal Lower Housing: Glass fiber reinforced PBT (UL94V-0) Movable Contact: Stainless steel with gold plating Stationary Contacts: Gold over copper alloy Switch Terminals: Brass with tin plating Environmental Data Operating Temperature Range: –25°C through +50°C (–13°F through +122°F) Humidity: 90-95% humidity for 240 hours @ 40°C (104°F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours Shock: 51G (500m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Cap Installation Force : 50.0N maximum downward force on actuator PCB Processing Soldering: Wave Soldering. See Profile A in Supplement section. Manual Soldering. See Profile A in Supplement section. Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL94V-0 lower housing The KP Series pushbuttons have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy.

Series KPMiniature Audio/Video Pushbuttons D37 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons D Illuminated PBSlides Programmable TogglesRockersTouch Tilt www.nkkswitches.com Distinctive Characteristics Actual Size KP series offers a complete switch solution for all broadcast panel needs, including home keys and the rectangular switch/cap assembly. Distinct, long total travel of .177” (4.5mm) for KP01 or shorter stroke of .138” (3.5mm) for KP02. Available with super bright red/green or amber/blue bicolor LED or RGB LED. The RGB LED full color spectrum in a switch package provides unlimited color combinations. Unique actuation guide gives positive indication of circuit transfer as well as smooth and silent operation. Choices of tactile, nontactile or tactile/audible actuation. Compact design with height of .906” (23.0mm) from PC board to top of cap. (Same height as programmable SmartSwitch™.) Flat, sculptured or home key square caps in three common sizes for design flexibility in audio/video applications. Twin contacts with gold plating assure high reliability and long life of 5,000,000 operations minimum.

Series KP Miniature Audio/Video Pushbuttons D38 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons DIlluminated PBSlides Programmable RockersTouch Tilt Toggles www.nkkswitches.com N Pole & Circuit 15A SPST OFF (ON) ( ) = Momentary Normally Open Contacts Contacts & Terminals G03 Gold Contacts and Straight PC Terminals; 100mA @ 12V DC 15A B G03K Housing K Black only Plungers A 9.2mm Plunger for 12.0mm Cap B 11.6mm Plunger for 15.0mm & 17.4mm Caps KP 01 ActuationTravel & Force 01 Stroke: 4.5mm (.177”) Actuation Force: 1.9N 02 Stroke: 3.5mm (.138”) Actuation Force: 1.6N C Tactile N Nontactile C Tactile N Nontactile S Tactile/Audible 11.6mm Plunger and 15.0mm Sculptured Cap Clear Lens and White Diffuser SPST OFF-Momentary ON Circuit Normally Open Contacts DESCRIPTION FOR TYPICAL ORDERING EXAMPLE KP0115ANBKG036CF-2SJB Super Bright Red/Green Bicolor LED Black Housing Gold Contacts with 100mA Rating Straight PC Terminals Nontactile Actuation TYPICAL SWITCH ORDERING EXAMPLE

Series KPMiniature Audio/Video Pushbuttons D39 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons D Illuminated PBSlides Programmable TogglesRockersTouch Tilt www.nkkswitches.com 6CF JBS2 Cap Types F Flat S Sculptured T Home Key LEDs 6CF Super Bright Red/Green Bicolor 6DG Super Bright Amber/Blue Bicolor RGB Red/Green/Blue * See Note Cap Sizes 1 12.0mm Square 2 15.0mm Square 3 17.4mm Square ** See Note Cap Colors JB Clear Lens & White Diffuser Bicolor Alternating Legend Caps JCF Red/Green JDG Amber/Blue Notes * RGB LED Page D44 ** Rectangular Cap Page D45 Alternating Legends

11 ON (pos) OFF (pos)

12 ON (neg) OFF (neg)

13 START STOP

14 OPEN CLOSE

Contact factory for custom options. Part Numbers for Alternating Legends Color Cap Size Flat Cap Sculptured Cap Home Key Cap Part Number Part Number Part Number Red/Green 12mm Square AT3093JCF11 ~ AT3093JCF14 AT3090JCF11 ~ AT3090JCF14 AT3096JCF11 ~ AT3096JCF14 15mm Square AT3094JCF11 ~ AT3094JCF14 AT3091JCF11 ~ AT3091JCF14 AT3097JCF11 ~ AT3097JCF14 17.4mm Square AT3095JCF11 ~ AT3095JCF14 AT3092JCF11 ~ AT3092JCF14 AT3098JCF11 ~ AT3098JCF14 Amber/Blue 12mm Square AT3093JDG11 ~ AT3093JDG14 AT3090JDG11 ~ AT3090JDG14 AT3096JDG11 ~ AT3096JDG14 15mm Square AT3094JDG11 ~ AT3094JDG14 AT3091JDG11 ~ AT3091JDG14 AT3097JDG11 ~ AT3097JDG14 17.4mm Square AT3095JDG11 ~ AT3095JDG14 AT3092JDG11 ~ AT3092JDG14 AT3098JDG11 ~ AT3098JDG14 Refer to Ordering Table for Alternating Legend that corresponds with last 2 digits of part number. TYPICAL SWITCH ORDERING EXAMPLE

Series KP Miniature Audio/Video Pushbuttons D40 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons DIlluminated PBSlides Programmable RockersTouch Tilt Toggles www.nkkswitches.com ACTUATION C Tactile KP01 or KP02 Gold Contacts Straight PC Terminals 100mA @ 12V DCG03 Black onlyKN Nontactile KP01 or KP02 HOUSING CONTACTS, TERMINALS, & RATING Tactile/Audible KP02 only S Plunger Position ( ) = Momentary Connected Terminals Throw & Switch Schematic Pole Model Normal Down Normal Down Note: Switch terminals “1” & “1a” are actually marked on the switch. SP KP0115A KP0215A OFF (ON) Normally Open 1-1a SPST POLE & CIRCUIT SUPER BRIGHT BICOLOR LED SPECIFICATIONS Amber can be achieved by simultaneous illumination of Red & Green. Purple can be achieved by simultaneous illumination of Amber & Blue. Red Green Amber Blue Unit Minimum Luminous Intensity IV 230 220 204 113 mcd Standard Luminous Intensity IV 290 270 340 188 mcd Maximum Forward Current IFM 25 for Amber 22 for Amber 30 25 mA Typical Forward Current IF 15 5 20 20 mA Forward Voltage VF 2.0 3.1 2.1 3.2 V Power Peak Dissipation PD 72 88 75 100 mW Maximum Reverse Voltage VRM 5 7 4 4 V Wavelength at Peak Emission λ 620 ~ 630 528 ~ 538 583 ~ 595 464 ~ 476 nm Current Reduction Rate Above 25°C ∆IF 0.40 0.36 0.40 0.33 mA/°C Ambient Temperature Range –25 ~ +50 –25 ~ +50 °C Colors LEDs are an integral part of the switch and are not available separately. LED circuit is isolated and requires an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. ATTENTION ELECTROSTATIC SENSITIVE DEVICES 6CF 6DG The electrical specifications shown are determined at a basic temperature of 25°C. (+) COM Green or Blue Red or Amber (–) L1 (–) L2 1 (COM)

Series KPMiniature Audio/Video Pushbuttons D41 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons D Illuminated PBSlides Programmable TogglesRockersTouch Tilt www.nkkswitches.com

1 Used on A Plunger

CAP TYPES & COLORS S AT3086 Home Key CapT AT3084 Flat Cap F AT3079 Sculptured Cap S AT3087 Home Key Cap T 12.0mm Square AT3078 Sculptured Cap AT3085 Flat Cap AT3080 Sculptured CapS AT3088 Home Key Cap T 2 15.0mm Square F 3 17.4mm Square Used on B Plunger Used on B Plunger (6.5) .256 (12.0) Sq .472 (7.0) .276 (15.0) Sq .591 (7.0) .276 (17.4) Sq .685 (7.0) .276 (17.4) Sq .685 (6.5) .256 (12.0) Sq .472 (2.6) Dia .102 (7.0) .276 (15.0) Sq .591 (2.6) Dia .102 (7.0) .276 (17.4) Sq .685 (2.6) Dia .102 (6.5) .256 (12.0) Sq .472 (7.0) .276 (15.0) Sq .591 Caps for Bicolor and RGB PLUNGERS A 9.2mm Plunger for 12.0mm Cap 9.2mm Plunger is designed with a narrower neck to hold the 12.0mm Cap. 11.6mm Plunger for 15.0mm & 17.4mm Caps B 11.6mm Plunger is designed with a wider neck to hold both the 15.0mm and 17.4mm Caps. (9.2) .362 (6.4) .252 (11.6) .457 (6.4) .252

Series KP Miniature Audio/Video Pushbuttons D42 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons DIlluminated PBSlides Programmable RockersTouch Tilt Toggles www.nkkswitches.com Clear Lens White Diffuser JB Lens & Diffuser Colors Available: Clear/White Materials & Finishes: Lens - Polycarbonate with glossy finish Diffuser - Polycarbonate with textured finish Optional Protective Guard AT4170 available; contact factory. Cap illumination is alternating Green/Red or Blue/Amber; legend text is black. Contact factory for other Alternating Legends. Legend illustrations are approximate representations of the actual characters on the filters. 11 12 13ON OFF ON OFF START STOP Standard Alternating Legend Pairs Green/Red or Blue/Amber Green/Red or Blue/Amber Green/Red or Blue/Amber Green/Red or Blue/Amber Caps for Alternating Legends AT3093 Flat Cap F S AT3096 Home Key CapT AT3094 Flat Cap F AT3091 Sculptured Cap S AT3097 Home Key Cap T 12.0mm Square AT3090 Sculptured Cap AT3095 Flat Cap AT3092 Sculptured CapS AT3098 Home Key Cap T 2 15.0mm Square F 3 17.4mm Square Used on B Plunger Used on B Plunger (6.5) .256 (12.0) Sq .472 ON (6.5) .256 (12.0) Sq .472 ON (6.5) .256 (12.0) Sq .472 (2.6) Dia .102 ON (7.0) .276 (15.0) Sq .591 ON (7.0) .276 (15.0) Sq .591 ON ON (7.0) .276 (15.0) Sq .591 (2.6) Dia .102 (7.0) .276 (17.4) Sq .685 (2.6) Dia .102 ON(7.0) .276 (17.4) Sq .685 ON (7.0) .276 (17.4) Sq .685 ON

Series KPMiniature Audio/Video Pushbuttons D43 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons D Illuminated PBSlides Programmable TogglesRockersTouch Tilt www.nkkswitches.com TYPICAL SWITCH DIMENSIONS 12.0mm Square Cap 15.0mm Square Cap KP0115ACAKG036CF-1SJB KP0115ANBKG036CF-2SJB 17.4mm Square Cap KP0115ANBKG036CF-3SJB (0.9) Dia Typ .035 (0.6) Dia Typ .024 (1.3) Dia Typ .051 (7.62) .300 (4.5) .177 (12.7) .500 (2.54) Typ .100 (12.7) .500 L2L1 1 1a C (0.9) Dia Typ .035 (0.6) Dia Typ .024 (1.3) Dia Typ .051 (7.62) .300 (4.5) .177 (12.7) .500 (2.54) Typ .100 (12.7) .500 L2L1 1 1a C (0.9) Dia Typ .035 (0.6) Dia Typ .024 (1.3) Dia Typ .051 (7.62) .300 (4.5) .177 (12.7) .500 (2.54) Typ .100 (12.7) .500 L2L1 1 1a C (12.0) Sq .472 (6.5) .256 (3.6) .142 (0.3) .012 (4.5) .177 (12.7) .500 (0.25) .010 (11.5) .453 (1.1) .043 (6.0) .236 (23.0) .906 (5.0) .197 (6.4) .252 (7.62) .300 (0.6) Typ .024 (12.7) .500 (15.0) Sq .591 L1L2 COM (5.08) .200 – + 0.5 (0.37) Typ .015 (15.0) Sq .591 (7.0) .276 (3.6) .142 (11.5) .453 (4.5) .177 (23.0) .906 (6.0) .236 (1.1) .043 (6.4) .252 (0.3) .012 (4.5) .177 (12.7) .500 (0.25) .010 (7.62) .300 (0.6) Typ .024 (12.7) .500 (15.0) Sq .591 L1L2 COM (5.08) .200 – + 0.5 (0.37) Typ .015 (17.4) Sq .685 (7.62) .300 (0.6) Typ .024 (12.7) .500 (15.0) Sq .591 L1L2 COM (5.08) .200 – + 0.5 (0.37) Typ .015 (11.5) .453 (1.1) .043 (6.0) .236 (23.0) .906 (4.5) .177 (7.0) .276 (3.6) .142 (6.4) .252 (0.3) .012 (4.5) .177 (12.7) .500 (0.25) .010 KP0115ANBKG036DG-2SJDG Bicolor Alternating Legend • 15.0mm Square Cap (15.0) Sq .591 (7.0) .276 (3.6) .142 (11.5) .453 (4.5) .177 (23.0) .906 (6.0) .236 (1.1) .043 (6.4) .252 (0.3) .012 (4.5) .177 (12.7) .500 (0.25) .010 (7.62) .300 (0.6) Typ .024 (12.7) .500 (15.0) Sq .591 L1L2 COM (5.08) .200 – + 0.5 (0.37) Typ .015 (0.9) Dia Typ .035 (0.6) Dia Typ .024 (1.3) Dia Typ .051 (7.62) .300 (4.5) .177 (12.7) .500 (2.54) Typ .100 (12.7) .500 L2L1 1 1a C

Series KP Miniature Audio/Video Pushbuttons D44 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons DIlluminated PBSlides Programmable RockersTouch Tilt Toggles www.nkkswitches.com 12.0mm Square Cap with RGB LED 15.0mm & 17.4mm Square Caps with RGB LED Terminal Detail (12.7) .500 Dia .500 (12.7) (4.5) .028 Typ Typ .035 (0.7) Dia (0.9) Dia .177 .300 (7.62) .051 (1.3) Typ .150 (3.81) Typ .060 (1.52) G(-)R(-) B(-) (+) (12.0) Sq .472 (15.0) Sq .591 (17.4) Sq .685 Sq(15.0) .591 (12.7) .500 Typ(1.52) .060 (7.62) .300 1 (4.5) .177 Typ .024 (0.6) See Terminal Detail (12.7) .500 Dia .500 (12.7) (4.5) .028 Typ Typ .035 (0.7) Dia (0.9) Dia .177 .300 (7.62) .051 (1.3) Typ .150 (3.81) Typ .060 (1.52) G(-)R(-) B(-) (+) Terminal Detail KP0115ACAKG03RGB-1SJB KP0115ANBKG03RGB-3SJB 17.4mm Cap KP0115ANBKG03RGB-2SJB RGB The electrical specifications shown are determined at a basic temperature of 25°C. LEDs are an integral part of the switch and are not available separately. LED circuit is isolated and requires an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement Section. Note: For applications that require white illumination, contact factory. Red Green Blue Unit Maximum Forward Current IFM 30 30 30 mA Typical Forward Current IF 20 14 9 mA Forward Voltage VF 2.0 2.9 2.9 V Power Peak Dissipation PD 60 80 80 mW Maximum Reverse Voltage VRM 5 5 5 V Dominant Wavelength λd 621.5 522.5 472.5 nm Current Reduction Rate Above 25°C ∆IF 0.50 0.50 0.50 mA/°C Ambient Temperature Range –25 ~ +50 °C Red Green Blue Common Anode (+) RGB Color 15.0mm Cap LED SPECIFICATIONS TYPICAL SWITCH DIMENSIONS ATTENTION ELECTROSTATIC SENSITIVE DEVICES .500 (5.0) .197.256 (6.5) (1.1) .043 (4.0)(23.0) .906 .157 (11.5) .453 .008 (0.2) .150 (3.81) (6.4) .252 .142 (3.6) (12.7) (0.3) .012 (3.81) (4.5) .177 (1.1) (7.0) .276 .043 (4.0)(23.0) .906 .157 (11.5) .453 (0.2) .008 .150 (6.4) .252 .142 (3.6) (12.7) .500 .012 (0.3) G(-) R(-) B(-) Common Anode (+) (0.5) Typ .020 G(-) R(-) B(-) Common Anode (+) (0.5) Typ .020 (4.5) .177 Sq .591 (15.0) (12.7) .500 .060 (1.52) Typ (7.62) .300 Typ(0.6) .024 See Terminal Detail

Series KPMiniature Audio/Video Pushbuttons D45 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons D Illuminated PBSlides Programmable TogglesRockersTouch Tilt www.nkkswitches.com RECTANGULAR CAP ASSEMBLY LED Holder The electrical specifications shown are determined at a basic temperature of 25°C. Center LED is an integral part of the switch. LEDs are not sold separately. LED circuits are isolated and require an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by us- ing the formula in the Supplement Section. Red Unit Maximum Forward Current IFM 30 mA Typical Forward Current IF 20 mA Forward Voltage VF 2.0 V Maximum Reverse Voltage VRM 4 V Dominant Wavelength λd 623 nm Current Reduction Rate Above 25°C ∆IF 0.32 mA/°C Ambient Temperature Range –25 ~ +50 °C Color LED Switch/Rectangular Cap assembly has 3 LEDs to achieve bright and even illumination. One LED (in center of switch bottom) is an integral part of the switch; the other 2 LEDs and 2 LED Holders are packaged separately. ASSEMBLY & INSTALLATION INSTRUCTIONS (12.7) .500 (3.1) .122 Dia (2.54) .100Cathode (4.8) .189 (5.9) .232 (10.4) .409 (6.7) .264 (+) (-) KP0115ACBKG03CJB for Tactile KP0115ANBKG03CJB for Nontactile Install LED into LED Holder (quantity 2). Solder LEDs and LED Holders into PCB. Solder switch into PCB making sure that the two outer LEDs and LED Holders clear the bot- tom side opening of the cap. (17.4) .685 (34.8) 1.370 PCB LED HolderLED Switch .500 (12.7) (4.5) .177 .300 (7.62) (22.86) .900(2.54) .100 (2.54) .100 .500 (12.7) (1.3) Dia Typ .051 (0.8) Dia Typ .031 (0.9) Dia Typ .035 Footprint Typ .018 (0.45) Sq(0.6) .024 Sq(15.0) .591 (12.7) .500 (4.5) .177 (7.62) .300 (0.3) .012 L–.500 .276 (7.0) (23.0) .906 (6.0) .236 .100 (2.54) (12.7) (3.6) .142 See below for complete assembly of switch, LEDs and LED holders. Contact factory for other LED colors. LED SPECIFICATIONS CAP ASSEMBLY DIMENSIONS Switch/Rectangular Cap Assembly

Series KP Miniature Audio/Video Pushbuttons D46 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons DIlluminated PBSlides Programmable RockersTouch Tilt Toggles www.nkkswitches.com ASSEMBLY INSTRUCTIONS FOR SQUARE CAPS As shown in the accompanying illustration, the cap and plunger are designed with tabs and notches to assure proper orientation of the cap on the switch. Holding the switch tightly, pull the cap off the switch. Once the cap assembly is released from the plunger, the lens and diffuser can be separated. Pry up the lens with fingernail or flat tip screwdriver inserted at the step on the diffuser. After aligning notches with tabs, join the lens and diffuser. Hold the switch tightly without touching the terminals. Firmly press the cap onto the plunger by applying pressure from one side to the other until both are snapped together. Cap Orientation Notch Tab Step Plunger Notches Cap Assembly Plunger Switch ATTENTION ELECTROSTATIC SENSITIVE DEVICES Removal of Cap Assembly & Separation of Lens & Diffuser Installation or Replacement of Cap

Series KPMiniature Audio/Video Pushbuttons D47 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons D Illuminated PBSlides Programmable TogglesRockersTouch Tilt www.nkkswitches.com LEGENDS Lens Film Insert Diffuser STOP (10.5) Dia .413 (8.97) Dia .353 (0.76) Typ .030 (13.0) Dia .512 (11.48) Dia .452 (0.76) Typ .030 (15.3) Dia .602 (0.76) Typ .030 (13.77) Dia .542 (9.8) Sq .386 (8.28)Dia .326 (0.76) Typ .030 (0.5) R .020 (12.8) Sq .504 (11.28) Dia .444 (0.76) Typ .030 (0.5) R .020 Sculptured Cap Lens Sculptured or Home Key Cap Film Inserts Flat Cap Lens Flat Cap Film Inserts (9.8) Sq .386 (8.28) Sq .326 (0.76) Typ .030 (0.5) R .020 (12.8) Sq .504 (11.28) Sq .444 (0.76) Typ .030 (0.5) R .020 (13.4) Sq .528 (11.88) Dia .468 (0.76) Typ .030 (0.5) R .020 (12.0) Sq .472 (9.8) Sq .386 (15.0) Sq .591 (12.8) Sq .504 (17.4) Sq .685 (13.4) Sq .528 Printing on Diffuser is not advisable. Recommended Methods: Laser Etch on clear lens, Screen Print, or Pad Print on lens. Laser Print on film insert. Epoxy based ink is recommended. Rectangular Cap Lens Rectangular Film Insert (13.77) .542 (0.91) Typ .036 (15.6) .614 (33.0) 1.299 (28.75) 1.132 (0.5) R .020 (2.125) Typ .084 Film Insert Material and Thickness: Clear Polyester; 4 mil (100µ) maximum thickness (13.4) Sq .528 (11.88) Dia .468 (0.76) Typ .030 (0.5) R .020 (13.77) .542 (0.76) Typ .030 (15.3) .602 (30.28) 1.192 (28.75) 1.132 NKK Switches can provide custom legends for caps. Contact factory for more information. Suggested Printable Areas for KP Lens Shaded areas are suggested printable areas for Film Insert. Suggested Printable Areas for KP Film Insert Shaded areas are suggested printable areas for Lens.