KP0215ACAKG03

KP0115ACAKG03 NKK | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 8

Technical content

Series KP Miniature Audio/Video 4-Pin RGB Pushbuttons www.nkkswitches.com General Specifications Electrical Capacity (Resistive Load) Low Level: 100mA maximum @ 12V DC Other Ratings Contact Resistance: 200 milliohms maximum Insulation Resistance: 100 megohms minimum @ 250V DC Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum 1,500V AC minimum between contacts & case for 1 minute minimum Mechanical Life: 5,000,000 operations minimum; Electrical Life: 5,000,000 operations minimum Nominal Operating Force: KP01: 1.9N maximum for Tactile & Nontactile models (at center of cap) KP02: 1.6N maximum for Tactile, Nontactile & Tactile/Audible models (at center of cap) Materials & Finishes Plunger/Upper Housing: Polyacetal Lower Housing: Glass fiber reinforced PBT (UL94V-0) Movable Contact: Stainless steel with gold plating Stationary Contacts: Gold over copper alloy Switch Terminals: Brass with tin plating Environmental Data Operating Temperature Range: –25°C through +50°C (–13°F through +122°F) Humidity: 90 - 95% humidity for 240 hours @ 40°C (104°F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours Shock: 51G (500m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Cap Installation Force : 50.0N maximum downward force on actuator PCB Processing Soldering: Wave Soldering. Preheat Temperature: 140°C @ 60 seconds; Peak Temperature: 270°C @ 11 seconds; Thickness of PCB: 1.6mm; Cycles: 2 Manual Soldering. 410°C @ 4 seconds for 2 cycles Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL94V-0 lower housing The KP Series pushbuttons have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy.

Series KPMiniature Audio/Video 4-Pin RGB Pushbuttons www.nkkswitches.com Distinctive Characteristics Actual Size KP series offers a complete switch solution for all broadcast panel needs, including the newest line of RGB LED options with four terminals. Distinct, long total travel of .177” (4.5mm) for KP01 or shorter stroke of .138” (3.5mm) for KP02. The super bright RGB LED provides vibrant full color spectrum in unlimited color combinations. Unique actuation guide gives positive indication of circuit transfer as well as smooth and silent operation. Choices of tactile, nontactile or tactile/audible actuation. Compact design with height of .906” (23.0mm) from PC board to top of cap. (Same height as programmable SmartSwitch™.) Flat, sculptured or home key square caps in three common sizes for design flexibility in audio/video applications. Twin contacts with gold plating assure high reliability and long life of 5,000,000 operations minimum. Improved profile for soldering specifications. Custom legends are available.

Series KP Miniature Audio/Video 4-Pin RGB Pushbuttons www.nkkswitches.com N Pole & Circuit 15A SPST OFF (ON) ( ) = Momentary Normally Open Contacts Contacts & Terminals G03 Gold Contacts and Straight PC Terminals; 100mA @ 12V DC 15A B G03K Housing K Black only Plungers A 9.2mm Plunger for 12.0mm Cap B 11.6mm Plunger for 15.0mm & 17.4mm Caps KP 01 ActuationTravel & Force 01 Stroke: 4.5mm (.177”) Actuation Force: 1.9N 02 Stroke: 3.5mm (.138”) Actuation Force: 1.6N C Tactile N Nontactile C Tactile N Nontactile S Tactile/Audible 11.6mm Plunger and 15.0mm Sculptured Cap Clear Lens and White Diffuser SPST OFF-Momentary ON Circuit Normally Open Contacts DESCRIPTION FOR TYPICAL ORDERING EXAMPLE KP0115ANBKG03RGBP-2SJB Super Bright RGB LED Black Housing Gold Contacts with 100mA Rating Straight PC Terminals Nontactile Actuation TYPICAL SWITCH ORDERING EXAMPLE

Series KPMiniature Audio/Video 4-Pin RGB Pushbuttons www.nkkswitches.com RGBP JBS2 Cap Types F Flat S Sculptured T Home Key LED RGBP Red/Green/Blue Cap Sizes 1 12.0mm Square 2 15.0mm Square 3 17.4mm Square Cap Colors JB Clear Lens & White Diffuser TYPICAL SWITCH ORDERING EXAMPLE ACTUATION C Tactile KP01 or KP02 Gold Contacts Straight PC Terminals 100mA @ 12V DCG03 Black onlyKN Nontactile KP01 or KP02 HOUSING CONTACTS, TERMINALS, & RATING Tactile/Audible KP02 only S Plunger Position ( ) = Momentary Connected Terminals Throw & Switch Schematic Pole Model Normal Down Normal Down Note: Switch terminals “1” & “1a” are actually marked on the switch. SP KP0115A KP0215A OFF (ON) Normally Open 1-1a SPST POLE & CIRCUIT 1 (COM) PLUNGERS A 9.2mm Plunger for 12.0mm Cap 9.2mm Plunger is designed with a narrower neck to hold the 12.0mm Cap. 11.6mm Plunger for 15.0mm & 17.4mm Caps B 11.6mm Plunger is designed with a wider neck to hold both the 15.0mm and 17.4mm Caps. (9.2) .362 (6.4) .252 (11.6) .457 (6.4) .252

Series KP Miniature Audio/Video 4-Pin RGB Pushbuttons www.nkkswitches.com

1 Used on A Plunger

CAP TYPES & COLORS S AT3086 Home Key CapT AT3084 Flat Cap F AT3079 Sculptured Cap S AT3087 Home Key Cap T 12.0mm Square AT3078 Sculptured Cap AT3085 Flat Cap AT3080 Sculptured CapS AT3088 Home Key Cap T 2 15.0mm Square F 3 17.4mm Square Used on B Plunger Used on B Plunger (6.5) .256 (12.0) Sq .472 (7.0) .276 (15.0) Sq .591 (7.0) .276 (17.4) Sq .685 (7.0) .276 (17.4) Sq .685 (6.5) .256 (12.0) Sq .472 (2.6) Dia .102 (7.0) .276 (15.0) Sq .591 (2.6) Dia .102 (7.0) .276 (17.4) Sq .685 (2.6) Dia .102 (6.5) .256 (12.0) Sq .472 (7.0) .276 (15.0) Sq .591 Clear Lens White Diffuser JB Lens & Diffuser Colors Available: Clear/White Materials & Finishes: Lens - Polycarbonate with glossy finish Diffuser - Polycarbonate with textured finish Optional Protective Guard AT4170 available; contact factory. RGB LED SPECIFICATIONS Red Green Blue Unit Note: For applications that require white illumination, contact factory. Maximum Forward Current IFM 50 30 30 mA Typical Forward Current IF 15 16 10 mA *Forward Voltage VF 2.0 2.9 2.9 V Power Peak Dissipation PD 100 80 80 mW Maximum Reverse Voltage VRM 5 5 5 V Dominant Wavelength λd 620 525 467 nm Current Reduction Rate Above 45°C ∆IF 0.75 0.25 **0.22 mA/°C Ambient Temperature Range –25 ~ +50 °C *Forward Voltage (VF) and Dominant Wavelength ( λd) are Typical Value measured by Typical Forward Current (I F). **Current Reduction Rate (∆ IF ) Above 40°C Red Green Blue Common Anode (+) RGBP Color ATTENTION ELECTROSTATIC SENSITIVE DEVICES The electrical specifications shown are determined at a basic temperature of 25°C. LEDs are an integral part of the switch and not available separately. LED circuit is isolated and requires an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula shown here. R = E – VF IF Where: R E V F IF = Resistor Value (Ohms) = Source Voltage (V) = Forward Voltage (V) = Forward Current (A) VF I FR + E Anode Cathode

Series KPMiniature Audio/Video 4-Pin RGB Pushbuttons www.nkkswitches.com TYPICAL SWITCH DIMENSIONS ASSEMBLY INSTRUCTIONS FOR SQUARE CAPS As shown in the accompanying illustration, the cap and plunger are designed with tabs and notches to assure proper orientation of the cap on the switch. Holding the switch tightly, pull the cap off the switch. Once the cap assembly is released from the plunger, the lens and diffuser can be separated. Pry up the lens with fingernail or flat tip screwdriver inserted at the step on the diffuser. After aligning notches with tabs, join the lens and diffuser. Hold the switch tightly without touching the terminals. Firmly press the cap onto the plunger by applying pressure from one side to the other until both are snapped together. Cap Orientation Notch Tab Step Plunger Notches Cap Assembly Plunger Switch ATTENTION ELECTROSTATIC SENSITIVE DEVICES Removal of Cap Assembly & Separation of Lens & Diffuser Installation or Replacement of Cap 12.0mm Square Cap 15.0mm Square Cap Terminal Detail KP0115ACAKG03RGBP-1SJB 17.4mm Square Cap (12.0) Sq .472 (6.5) .256 (3.6) .142 (0.45) Dia Typ .018 (12.7) .500 (0.3) .012 (1.1) .043 (23.0) .906 (5.0) .197 (6.4) .252 (3.81) .150 (4.0) .157 (15.0) Sq .591 .906 (23.0) .177 (4.5) (1.1) .043 (6.4) .252 (3.6) .142 .276 (7.0) (0.45) Dia Typ .018 (12.7) .500 (0.3) .012 (3.81) .150 (4.0) .157 (17.4) Sq .685 (4.5) .177 (1.1) (7.0) .276 .043 (23.0) .906 (6.4) .252 .142 (3.6) (0.45) Dia Typ .018 (12.7) .500 (3.81) .150 (4.0) .157 (0.3) .012 (0.9) Dia Typ .035 (0.7) Dia Typ .028 (1.3) Dia Typ .051 (7.62) .300 (4.5) .177 (12.7) .500 (1.52) .060 (12.7) .500 1 1a (0.76) .030 (1.91) Dia Typ .075 (0.9) Dia Typ .035 (0.7) Dia Typ .028 (1.3) Dia Typ .051 (7.62) .300 (4.5) .177 (12.7) .500 (1.52) .060 (12.7) .500 1 1a (0.76) .030 (1.91) Dia Typ .075 (0.9) Dia Typ .035 (0.7) Dia Typ .028 (1.3) Dia Typ .051 (7.62) .300 (4.5) .177 (12.7) .500 (1.52) .060 (12.7) .500 1 1a (0.76) .030 (1.91) Dia Typ .075 (4.5) .177 Sq .591 (15.0) (12.7) Typ .500 (7.62) .300 Typ(0.6) .024 See Terminal Detail (4.5) .177 Sq .591 (15.0) (12.7) Typ .500 (7.62) .300 Typ(0.6) .024 See Terminal Detail See Terminal DetailSq(15.0) .591 (12.7) .500 (7.62) .300 (4.5) .177 Typ .024 (0.6) Terminal Detail KP0115ANBKG03RGBP-2SJB Terminal Detail KP0115ANBKG03RGBP-3SJB (1.52) .060 Common Anode (+) B (–) G (–) R (–) (0.76) .030 (1.52) .060 Common Anode (+) B (–) G (–) R (–) (0.76) .030 (1.52) .060 Common Anode (+) B (–) G (–) R (–) (0.76) .030

Series KP Miniature Audio/Video 4-Pin RGB Pushbuttons www.nkkswitches.com 7850 East Gelding Drive • Scottsdale, AZ 85260 • Telephone 480.991.0942 • Fax 480.998.1435 Effective Date May 2017 LEGENDS Lens Film Insert Diffuser STOP (10.5) Dia .413 (8.97) Dia .353 (0.76) Typ .030 (13.0) Dia .512 (11.48) Dia .452 (0.76) Typ .030 (15.3) Dia .602 (0.76) Typ .030 (13.77) Dia .542 (9.8) Sq .386 (8.28)Dia .326 (0.76) Typ .030 (0.5) R .020 (12.8) Sq .504 (11.28) Dia .444 (0.76) Typ .030 (0.5) R .020 Sculptured Cap Lens Sculptured or Home Key Cap Film Inserts Flat Cap Lens Flat Cap Film Inserts (9.8) Sq .386 (8.28) Sq .326 (0.76) Typ .030 (0.5) R .020 (12.8) Sq .504 (11.28) Sq .444 (0.76) Typ .030 (0.5) R .020 (13.4) Sq .528 (11.88) Dia .468 (0.76) Typ .030 (0.5) R .020 (12.0) Sq .472 (9.8) Sq .386 (15.0) Sq .591 (12.8) Sq .504 (17.4) Sq .685 (13.4) Sq .528 Printing on Diffuser is not advisable. Recommended Methods: Laser Etch on clear lens, Screen Print on flat lens. Laser Print on film insert. Epoxy based ink is recommended. Film Insert Material and Thickness: Clear Polyester; 4 mil (100µ) maximum thickness (13.4) Sq .528 (11.88) Dia .468 (0.76) Typ .030 (0.5) R .020 NKK Switches can provide custom legends for caps. Contact factory for more information. Suggested Printable Areas for KP Lens Shaded areas are suggested printable areas for Film Insert. Suggested Printable Areas for KP Film Insert Shaded areas are suggested printable areas for Lens.