KP0115ANBKG03CF-2SJB

KP0115ACAKG03CF-1SJB GREATECS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

Miniature Audio/Video Pushbuttons KP Series General Specifications: KP How to order: 1 2 3 4 sales@greatecs.com www.greatecs.com 1 KP0115ACAKG03CF-1SJB 15A C N S A B K TRAVEL & FORCE: Stroke: 4.5mm (.177‘‘) Actuation Force: 1.9N Stroke: 3.5mm (.138‘‘) Actuation Force: 1.6N POLE & CIRCUITS: SPST OFF-(ON) Normally Open Contacts ACTUATION: Tactile Nontactile Tactile/Audible (just for 02 type) PLUNGERS: 9.2mm Plunger for 12.0mm Cap 11.6mm Plunger for 15.0mm and 17.4mm Caps HOUSING: Black Only G03 CF RGB CONTACTS & TERMINALS: Gold Contacts and Straight PC Terminals; 100mA @ 12V DC LEDS: Red/Green Bicolor Red/Green/Blue CAPS SIZES: 12.0mm Square 15.0mm Square 17.4mm Square Illuminated Switches 6 7 8 9 10 F S T CAP TYPES: Flat Sculpured Home Key JB CAPS COLORS: Clear Lens & White Diffuser Electrical Capacity (Resistive Load) Low Level: 100mA maximum @ 12V DC Other Ratings Contact Resistance: 200 milliohms maximum Insulation Resistance: 100 megohms minimum @ 250V DC Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum 1,500V AC minimum between contacts & case for 1 minute minimum Mechanical Life: 5,000,000 operations minimum; 1,000,000 operations minimum for custom Rectangular Switch/Cap Assembly (at center of cap) Electrical Life: 5,000,000 operations minimum Nominal Operating Force: KP01: 1.9N maximum for T actile & Nontactile models (at center of cap) KP02: 1.6N maximum for T actile, Nontactile & T actile/Audible models (at center of cap) Travel: KP01: Pretravel .122” (3.1mm); Overtravel .055” (1.4mm); Total Travel .177” (4.5mm) KP02: Pretravel .091” (2.3mm); Overtravel .047” (1.2mm); Total Travel .138” (3.5mm) Materials & Finishes Plunger/Upper Housing: Polyacetal Lower Housing: Movable Contact: Stainless steel with gold plating Stationary Contacts: Gold over copper alloy Switch Terminals: Brass with tin plating Environmental Data Operating Temp Range: –25°C through +50°C (–13°F through +122°F) Humidity: 90-95% humidity for 240 hours @ 40°C (104°F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours Shock: 51G (500m/s 2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Cap Installation Force : 50.0N maximum downw ard force on actuator PCB P rocessing Soldering: Cleaning: These devices are not process sea led. Hand clean locally us ing alcohol based solution. Standards & Cer ti/f_ications UL Recognition These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, th e results do not produce hazardous ene rgy. 12.0mm Square Cap (12.0) Sq .472 (0.9) Dia Ty p .035 (0.6) Dia Ty p .024 (1.3) Dia Ty p .051 (7.62) .300 (4.5) .177 (12.7) .500 (2.54) Ty p .100 (12.7) .500 L2 L1 1 1a C (6.5) .256 (3.6) .142 (0.3) .012 (4.5) .177 (12.7) .500 (0.45) Dia .018 (11.5) .453 (1.1) .043 (6.0) .236 (23.0) .906 (5.0) .197 (6.4) .252 (7.62) .300 (0.6) Ty p .024 (2.54) Ty p .100 (12.7) .500 (15.0) Sq .591 L1L2 COM 15.0mm Square Cap (0.9) Dia Ty p .035 (0.6) Dia Ty p .024 (1.3) Dia Ty p .051 (7.62) .300 (4.5) .177 (12.7) .500 (2.54) Ty p .100 (12.7) .500 L2 L1 1 1a C (15.0) Sq .591 (7.62) .300 (0.6) Ty p .024 (2.54) Ty p .100 (12.7) .500 (15.0) Sq .591 L1L2 COM (7.0) .276 (3.6) .142 (0.3) .012 (4.5) .177 (0.45) Dia .018 (12.7) .500 (11.5) .453 (4.5) .177 (23.0) .906 (6.0) .236 (1.1) .043 (6.4) .252 KP0115ANBKG03CF-2SJB 17.4mm Square Cap (17.4) Sq .685 (0.9) Dia Ty p .035 (0.6) Dia Ty p .024 (1.3) Dia Ty p .051 (7.62) .300 (4.5) .177 (12.7) .500 (2.54) Ty p .100 (12.7) .500 L2 L1 1 1a C (11.5) .453 (1.1) .043 (6.0) .236 (23.0) .906 (4.5) .177 (7.0) .276 (3.6) .142 (0.3) .012 (4.5) .177 (12.7) .500 (0.45) Dia .018 (6.4) .252 (7.62) .300 (0.6) Ty p .024 (2.54) Ty p .100 (12.7) .500 (15.0) Sq .591 L1L2 COM KP0115ANBKG03CF-3SJB Wave Soldering: See Pro/f_ile A in Supplement section. Manual Soldering: See Pro/f_ile A in Supplement section. Glass /f_iber reinforced PBT or CSA Certi/f_ication: The KP Series pushbuttons have not been tested for UL recognition or CSA certi/f_ication.

Miniature Audio/Video Pushbuttons KP Series sales@greatecs.com www.greatecs.com 2 KP0115ACAKG03RGB-1SJB CUTAWAY Illuminated Switches Plunger Position ( ) = Momentary Connected Terminals Throw & Switch Schematic Pole Model Normal Down Normal Down Note: Switch terminals “1” & “1a” are actually marked on the switch. SP KP0115A KP0215A OFF (ON) Normally Open 1-1a SPST POLE & CIRCUIT 1 (COM) POLE & CIRCUIT KP0115ANBKG03RGB-2SJB KP0115ANBKG03RGB-3SJB 12.0mm Square Cap with RGB LED 17.4mm Square Caps with RGB LED Terminal Detail (12.7) .500 Dia .500 (12.7 (4.5) .028 Typ Typ .035 (0.7) Dia (0.9) Dia .177 .300 (7.62) .051 (1.3) Typ .150 (3.81) Typ .060 (1.52) G(-)R(-) B(-)(+) (12.0) Sq .472 .500 (5.0) .197.256 (6.5) (1.1) .043 (4.0)(23.0) .906 .157 (11.5) .453 Typ .008 (0.2) Sq .150 (3.81) (6.4) .252 .142 (3.6) (12.7 (0.3) .012 (4.5) .177 Sq .591 (15.0) (12.7) .500 .060 (1.52)Typ (7.62) .300 Typ(0.6) .024 See Terminal Detail (15.0) Sq .591 (17.4) Sq .685 (3.81) (4.5) .177 (1.1) (7.0) .276 .043 (4.0)(23.0) .906 .157 (11.5) .453 TypSq(0.2) .008 .150 (6.4) .252 .142 (3.6) (12.7 .500 .012 (0.3) G(-) R(-) B(-) Common Anode (+) Sq(15.0) .591 (12.7) .500 Typ(1.52) .060 (7.62) .300 1 (4.5) .177 Typ .024 (0.6) See Terminal Detail (12.7) .500 Dia .500 (12.7 (4.5) .028 Typ Typ .035 (0.7) Dia (0.9) Dia .177 .300 (7.62) .051 (1.3) Typ .150 (3.81) Typ .060 (1.52) G(-)R(-) B(-)(+) Terminal Detail G(-) R(-) B(-) Common Anode (+) G(-) R(-) B(-) Common Anode (+) Terminal Detail (12.7) .500 Dia .500 (12.7 (4.5) .028 Typ Typ .035 (0.7) Dia (0.9) Dia .177 .300 (7.62) .051 (1.3) Typ .150 (3.81) Typ .060 (1.52) G(-)R(-) B(-)(+) Sq(15.0) .591 (12.7) .500 Typ(1.52) .060 (7.62) .300 1 (4.5) .177 Typ .024 (0.6) See Terminal Detail (3.81) (4.5) .177 (1.1) (7.0) .276 .043 (4.0)(23.0) .906 .157 (11.5) .453 TypSq(0.2) .008 .150 (6.4) .252 .142 (3.6) (12.7 .500 .012 (0.3)15mm Square Caps with RGB LED PLUNGERS A 9.2mm Plunger for 12.0mm Cap 9.2mm Plunger is designed with a narrower neck to hold the 12.0mm Cap. (9.2) .362 (6.4) .252 11.6mm Plunger for 15.0mm & 17.4mm Caps B 11.6mm Plunger is designed with a wider neck to hold both the 15.0mm and 17.4mm Caps. (11.6) .457 (6.4) .252

Miniature Audio/Video Pushbuttons KP Series sales@greatecs.com www.greatecs.com 3 Illuminated Switches BICOLOR LED SPECIFICATIONS determined at a basic temperature of 25°C. LEDs are an integral part of the switch and are not available separately. LED circuit is isolated and requires an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement Section. Note: For applications that require white illumination, contact factory. Red Green Blue Unit Forward Peak Current I FM 30 30 30 mA Continuous Forward Current I F 20 15 15 mA Forward Voltage V F 2.0 3.3 3.4 V Power Peak Dissipation P D 40 80 80 mW Reverse Peak Voltage V RM 555 V Dominant Wavelength λ d 625 525 470 nm Current Reduction Rate Above 25°C Δ IF 0.50 0.50 0.50 mA/°C Ambient Temperature Range –25 ~ +50 °C Red Green Blue Common Anode (+) RGBAttention Electrostatic Sensitive Devices Color CUSTOM RGB LED SPECIFICATIONS Amber can be achieved by simultaneous illumination of Red & Green. Attention Electrostatic Sensitive Devices Red Green Unit Minimum Luminous Intensity I V 30 50 mcd Standard Luminous Intensity I V 60 115 mcd Forward Peak Current I FM (25 for amber) (22 for amber) mA Continuous Forward Current I F 20 20 mA Forward Voltage V F 2.1 3.5 V Power Peak Dissipation PD 75 100 mW Reverse Peak Voltage V RM 44 V Wavelength at Peak Emission λ 619 ~ 630 520 ~ 535 nm Current Reduction Rate Above 25°C ΔI F 0.38 0.32 mA/°C Ambient Temperature Range –25 ~ +50 °C CF Colors (+) COM Red Green (–) L 2 (–) L1 LEDs are an integral part of the switch and are not avail - able separately. LED circuit is isolated and requires an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. AThe electrical specifications shown are determined at a basic temperature of 25°C

Miniature Audio/Video Pushbuttons KP Series sales@greatecs.com www.greatecs.com 4 Illuminated Switches CAP TYPES & COLORS

1 Used on A Plunger

AT3083 Flat Cap F S AT3086 Home Key CapT AT3084 Flat Cap F AT3079 Sculptured Cap S AT3087 Home Key Cap T 12.0mm Square AT3078 Sculptured Cap AT3085 Flat Cap AT3080 Sculptured CapS AT3088 Home Key Cap T Clear Lens White Diffuser JB Lens & Diffuser Colors Available: Clear/White Optional Protective Guard AT4170 available; contact factory. 2 15.0mm Square F 3 17.4mm Square Used on B Plunger Used on B Plunger (6.5) .256 (12.0) Sq .472 (6.5) .256 (12.0) Sq .472 (7.0) .276 (15.0) Sq .591 (7.0) .276 (15.0) Sq .591 (7.0) .276 (17.4) Sq .685 (7.0) .276 (17.4) Sq .685 (6.5) .256 (12.0) Sq .472 (2.6) Dia .102 (7.0) .276 (15.0) Sq .591 (2.6) Dia .102 (7.0) .276 (17.4) Sq .685 (2.6) Dia .102 Materials & Finishes: Lens - Palycarbonate with glossy finish; Diffuser - Polycarbonate with textured finish

Miniature Audio/Video Pushbuttons KP Series sales@greatecs.com www.greatecs.com 5 Illuminated Switches CUSTOM RECTANGULAR CAP ASSEMBLY Switch/Rectangular Cap Assembly LED Holder determined at a basic temperature of 25°C. Center LED is an integral part of the switch. LEDs are not sold separately. LED circuits are isolated and require an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by us- ing the formula in the Supplement Section. Red Unit Forward Peak Current I FM 30 mA Continuous Forward Current I F 20 mA Forward Voltage V F 2.0 V Reverse Peak Voltage V RM 4V Dominant Wavelength λ d 623 nm Current Reduction Rate Above 25°C ΔI F 0.32 mA/°C Ambient Temperature Range –25 ~ +50 °C Color LED Switch/Rectangular Cap assembly has 3 LEDs to achieve bright and even illumination. One LED (in center of switch bottom) is an integral part of the switch; the other 2 LEDs and 2 LED Holders are packaged separately. ASSEMBLY & INSTALLATION INSTRUCTIONS (12.7) .500 (3.1) .122 Dia (2.54) .100Cathode (4.8) .189 (5.9) .232 (10.4) .409 (6.7) .264 (+) (-) KP0115ACBKG03CJB for Tactile KP0115ANBKG03CJB for Nontactile Install LED into LED Holder (quantity 2). Solder LEDs and LED Holders into PCB. Solder switch into PCB making sure that the two outer LEDs and LED Holders clear the bot - tom side opening of the cap. (17.4) .685 (34.8) 1.370 PCB LED HolderLED Switch .500 (12.7) (4.5) .177 .300 (7.62) (22.86) .900(2.54) .100 (2.54) .100 .500 (12.7) (1.3) Dia Ty p .051 (0.8) Dia Ty p .031 (0.9) Dia Ty p .035 Footprint Typ .018 (0.45) Sq(0.6) .024 Sq(15.0) .591 (12.7) .500 (4.5) .177 (7.62) .300 (0.3) .012 L–.500 .276 (7.0) (23.0) .906 (6.0) .236 .100 (2.54) (12.7 (3.6) .142 See below for complete assembly of switch, LEDs and LED holders. Contact factory for other LED colors. LED SPECIFICATIONS CAP ASSEMBLY DIMENSIONS The electrical specifications shown are

Miniature Audio/Video Pushbuttons KP Series sales@greatecs.com www.greatecs.com 6 Illuminated Switches ASSEMBLY INSTRUCTIONS FOR SQUARE CAPS As shown in the accompanying illus- tration, the cap and plunger are designed with tabs and notches to assure proper orientation of the cap on the switch. Holding the switch tightly, pull the cap off the switch. Once the cap as - sembly is released from the plunger, the lens and diffuser can be separated. Pry up the lens inserted at the step on the diffuser. Attention Electrostatic Sensitive Devices After aligning notches with tabs, join the lens and diffuser. Hold the switch tightly without touching the terminals. Firmly press the cap onto the plunger by applying pressure from one side to the other until both are snapped together. Removal of Cap Assembly Installation or Cap Orientation & Separation of Lens & Diffuser Replacement of Cap Notch Tab Step Plunger Notches Cap Assembly Plunger Switch LEGENDS Lens Film Insert Diffuser ST OP (10.5) Dia .413 (8.97)Dia .353 (0.76) Ty p .030 (13.0) Dia .512 (11.48) Dia .452 (0.76) Ty p .030 (15.3) Dia .602 (0.76) Ty p .030 (13.77) Dia .542 (9.8) Sq .386 (8.28)Dia .326 (0.76) Ty p .030 (0.5) R .020 (12.8) Sq .504 (11.28) Dia .444 (0.76) Ty p .030 (0.5) R .020 Sculptured Cap Lens Sculptured or Home Key Cap Film Inserts Flat Cap Lens Flat Cap Film Inserts (9.8) Sq .386 (8.28) Sq .326 (0.76) Ty p .030 (0.5) R .020 (12.8) Sq .504 (11.28) Sq .444 (0.76) Ty p .030 (0.5) R .020 (13.4) Sq .528 (11.88) Dia .468 (0.76) Ty p .030 (0.5) R .020 (12.0) Sq .472 (9.8) Sq .386 (15.0) Sq .591 (12.8) Sq .504 (17.4) Sq .685 (13.4) Sq .528 Printing on Diffuser is not advisable. Custom Rectangular Cap Lens Custom Rectangular Film Insert (13.77) .542 (0.91)Ty p .036 (15.6) .614 (33.0) 1.299 (28.75) 1.132 (0.5) R .020 (2.125)Ty p .084 Film Insert Material and Thickness: Clear Polyester; 4 mil (100μ) maximum thickness (13.4) Sq .528 (11.88) Dia .468 (0.76) Ty p .030 (0.5) R .020 (13.77) .542 (0.76) Ty p .030 (15.3) .602 (30.28) 1.192 (28.75) 1.132 Recommended Methods: Laser Etch, Screen Print, or Pad Print on lens; Epoxy based ink is recommended. Shaded areas are suggested printable areas for Lens & Film Inser t. General information and basic specifications are presented bere for customers who want to do their own legends.