KD1084AD2T

KD1084 STMICROELECTRONICS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 18

Technical content

■ TYPICAL DROPOUT 1.3V (AT 5A) ■ THREE TERMINAL ADJUSTABLE OR FIXED OUTPUT VOLTAGE 1.5V, 1.8V, 2.5V, 2.85V, 3.3V, 3.6V, 5V. ■ GUARANTEED OUTPUT CURRENT UP TO ■ OUPUT TOLERANCE ±1% AT 25°C AND ±2% IN FULL TEMPERATURE RANGE FOR THE "A" VERSION ■ OUPUT TOLERANCE ±2% AT 25°C AND ±3% IN FULL TEMPERATURE RANGE INTERNAL POWER AND THERMAL LIMIT ■ WIDE OPERATING TEMPERATURE RANGE -40°C TO 125°C ■ PACKAGE AVAILABLE : TO-220, D2PAK, D 2PAK/A, DPAK ■ PINOUT COMPATIBILITY WITH STANDARD ADJUSTABLE VREG

DESCRIPTION

The KD1084 is a LOW DROP Voltage Regulator able to provide up to 5A of Output Current. Dropout is guaranteed at a maximum of 1.5V at the maximum output current, decreasing at lower loads. The KD1084 is pin to pin compatible with the older 3-terminal adjustable regulators, but has better performances in term of drop and output tolerance . A 2.85V output version is suitable for SCSI-2 active termination. Unlike PNP regulators, where a part of the output current is wasted as quiescent current, the KD1084 quiescent current flows into the load, so increase efficiency. Only a 10µF minimum capacitor is need for stability. The devices are supplied in TO-220, D 2PAK, D 2PAK/A and DPAK. On chip trimming allows the regulator to reach a very tight output voltage tolerance, within ±1% at 25°C for "A" version and ±2% at 25°C for standard version. KD1084 SERIES 5A LOW DROP POSITIVE VOLTAGE REGULATOR ADJUSTABLE AND FIXED SCHEMATIC DIAGRAM TO-220 D 2PAK D 2PAK/ADPAK

Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. THERMAL DATA APPLICATION CIRCUITS Symbol Parameter² Value Unit VI DC Input Voltage 12 V IO Output Current Internally Limited mA PD Power Dissipation Internally Limited mW Tstg Storage Temperature Range -55 to +150 °C Top Operating Junction Temperature Range -40 to +125 °C Symbol Parameter TO-220 D 2PAK D 2PAK/A DPAK Unit R thj-case Thermal Resistance Junction-case 333 ° C / W R thj-amb Thermal Resistance Junction-ambient 50 62.5 50 °C/W R 2VO = VREF (1 +  )R 1

CONNECTION DIAGRAM (top view) ORDERING CODES (*) Available on request () Available in Tape & Reel with the suffix "R" for fixed versions and "-R" for adjustable version TO-220 D 2PAK D 2PAK/A DPAK TO-220 D 2PAK () D 2PAK/A DPAK OUTPUT VOLTAGE TOLERANCE KD1084V15 (*) KD1084D2T15 KD1084D2M15 KD1084DT15 1.5 V 2% KD1084AV15 (*) KD1084AD2T15 KD1084AD2M15 KD1084ADT15 1.5 V 1% KD1084V18 KD1084D2T18 KD1084D2M18 KD1084DT18 1.8 V 2% KD1084AV18 KD1084AD2T18 KD1084AD2M18 KD1084ADT18 1.8 V 1% KD1084V25 KD1084D2T25 KD1084D2M25 KD1084DT25 (*) 2.5 V 2% KD1084AV25 KD1084AD2T25 KD1084AD2M25 KD1084ADT25 (*) 2.5 V 1% KD1084V28 (*) KD1084D2T28 (*) KD1084D2M28 (*) KD1084DT28 (*) 2.85 V 2% KD1084AV28 (*) KD1084AD2T28 (*) KD1084AD2M28 (*) KD1084ADT28 (*) 2.85 V 1% KD1084V33 KD1084D2T33 KD1084D2M33 KD1084DT33 3.3 V 2% KD1084AV33 KD1084AD2T33 KD1084AD2M33 KD1084ADT33 3.3 V 1% KD1084V36 KD1084D2T36 KD1084D2M36 KD1084DT36 3.6 V 2% KD1084AV36 KD1084AD2T36 KD1084AD2M36 KD1084ADT36 3.6 V 1% KD1084V50 KD1084D2T50 KD1084D2M50 KD1084DT50 (*) 5.0 V 2% KD1084AV50 KD1084AD2T50 KD1084AD2M50 KD1084ADT50 (*) 5.0 V 1% KD1084V KD1084D2T KD1084D2M KD1084DT ADJ 2% KD1084AV KD1084AD2T KD1084AD2M KD1084ADT ADJ 1%

ELECTRICAL CHARACTERISTICS OF KD1084A#15 (VI=4.5V, CI = CO =10µF (Tant.), TA = -40 to 125°C, unless otherwise specified.) ELECTRICAL CHARACTERISTICS OF KD1084A#18 (VI=4.8V, CI = CO =10µF (Tant.), TA = -40 to 125°C, unless otherwise specified.) Symbol Parameter Test Conditions Min. Typ. Max. Unit VO Output Voltage I O = 0 mA T J = 25°C 1.485 1.5 1.515 V IO = 0 to 5A VI = 3.1 to 10V 1.47 1.5 1.53 V ΔVO Line Regulation I O = 0 mA V I = 3.1 to 10V TJ = 25°C 0.5 6 mV IO = 0 mA V I = 3.1 to 10V 1 6 mV ΔVO Load Regulation I O = 0 to 5A TJ = 25°C 3 15 mV IO = 0 to 5A 7 20 V Vd Dropout Voltage I O =5 A 1.3 1.5 V Iq Quiescent Current V I ≤ 10V 5 10 mA Isc Short Circuit Current V I - VO = 5V 5.5 7 A Termal Regulation T A = 25°C, 30ms pulse 0.003 0.015 %/W SVR Supply Voltage Rejection f = 120 Hz, C O = 25 µF, IO = 5A VI = 5 ± 1.5V 60 75 dB eN RMS Output Noise Voltage (% of VO ) TA = 25°C f =10Hz to 10KHz 0.003 % S Temperature Stability 0.5 % S Long Term Stability T A = 125°C 1000Hrs 0.5 % Symbol Parameter Test Conditions Min. Typ. Max. Unit VO Output Voltage I O = 0 mA T J = 25°C 1.782 1.8 1.818 V IO = 0 to 5A VI = 3.4 to 10V 1.764 1.8 1.836 V ΔVO Line Regulation I O = 0 mA V I = 3.4 to 10V TJ = 25°C 0.5 6 mV IO = 0 mA V I = 3.4 to 10V 1 6 mV ΔVO Load Regulation I O = 0 to 5A TJ = 25°C 3 15 mV IO = 0 to 5A 7 20 V Vd Dropout Voltage I O =5 A 1.3 1.5 V Iq Quiescent Current V I ≤ 10V 5 10 mA Isc Short Circuit Current V I - VO = 5V 5.5 7 A Termal Regulation T A = 25°C, 30ms pulse 0.003 0.015 %/W SVR Supply Voltage Rejection f = 120 Hz, C O = 25 µF, IO = 5A VI = 5.3 ± 1.5V 60 75 dB eN RMS Output Noise Voltage (% of VO ) TA = 25°C f =10Hz to 10KHz 0.003 % S Temperature Stability 0.5 % S Long Term Stability T A = 125°C 1000Hrs 0.5 %

ELECTRICAL CHARACTERISTICS OF KD1084A#25 (VI=5.5V, CI = CO =10µF (Tant.), TA = -40 to 125°C, unless otherwise specified.) ELECTRICAL CHARACTERISTICS OF KD1084A#285 (VI=5.85V, CI = CO =10µF (Tant.), TA = -40 to 125°C, unless otherwise specified.) Symbol Parameter Test Conditions Min. Typ. Max. Unit VO Output Voltage I O = 0 mA T J = 25°C 2.475 2.5 2.525 V IO = 0 to 5A VI = 4.1 to 10V 2.45 2.5 2.55 V ΔVO Line Regulation I O = 0 mA V I = 4.1 to 10V TJ = 25°C 0.5 6 mV IO = 0 mA V I = 4.1 to 10V 1 6 mV ΔVO Load Regulation I O = 0 to 5A TJ = 25°C 3 15 mV IO = 0 to 5A 7 20 V Vd Dropout Voltage I O =5 A 1.3 1.5 V Iq Quiescent Current V I ≤ 10V 5 10 mA Isc Short Circuit Current V I - VO = 5V 5.5 7 A Termal Regulation T A = 25°C, 30ms pulse 0.003 0.015 %/W SVR Supply Voltage Rejection f = 120 Hz, C O = 25 µF, IO = 5A VI = 6 ± 1.5V 60 72 dB eN RMS Output Noise Voltage (% of VO ) TA = 25°C f =10Hz to 10KHz 0.003 % S Temperature Stability 0.5 % S Long Term Stability T A = 125°C 1000Hrs 0.5 % Symbol Parameter Test Conditions Min. Typ. Max. Unit VO Output Voltage I O = 0 mA T J = 25°C 2.821 2.85 2.879 V IO = 0 to 5A VI = 4.5 to 10V 2.793 2.85 2.907 V ΔVO Line Regulation I O = 0 mA V I = 4.5 to 10V TJ = 25°C 0.5 6 mV IO = 0 mA V I = 4.5 to 10V 1 6 mV ΔVO Load Regulation I O = 0 to 5A TJ = 25°C 3 15 mV IO = 0 to 5A 7 20 V Vd Dropout Voltage I O =5 A 1.3 1.5 V Iq Quiescent Current V I ≤ 10V 5 10 mA Isc Short Circuit Current V I - VO = 5V 5.5 7 A Termal Regulation T A = 25°C, 30ms pulse 0.003 0.015 %/W SVR Supply Voltage Rejection f = 120 Hz, C O = 25 µF, IO = 5A VI = 6.35 ± 1.5V 60 72 dB eN RMS Output Noise Voltage (% of VO ) TA = 25°C f =10Hz to 10KHz 0.003 % S Temperature Stability 0.5 % S Long Term Stability T A = 125°C 1000Hrs 0.5 %

ELECTRICAL CHARACTERISTICS OF KD1084A#33 (VI=6.3V, CI = CO =10µF (Tant.), TA = -40 to 125°C, unless otherwise specified.) ELECTRICAL CHARACTERISTICS OF KD1084A#36 (VI=6.6V, CI = CO =10µF (Tant.), TA = -40 to 125°C, unless otherwise specified.) Symbol Parameter Test Conditions Min. Typ. Max. Unit VO Output Voltage I O = 0 mA T J = 25°C 3.267 3.3 3.333 V IO = 0 to 5A VI = 4.9 to 10V 3.234 3.35 3.366 V ΔVO Line Regulation I O = 0 mA V I = 4.9 to 10V TJ = 25°C 0.5 6 mV IO = 0 mA V I = 4.9 to 10V 1 6 mV ΔVO Load Regulation I O = 0 to 5A TJ = 25°C 3 15 mV IO = 0 to 5A 7 20 V Vd Dropout Voltage I O =5 A 1.3 1.5 V Iq Quiescent Current V I ≤ 10V 5 10 mA Isc Short Circuit Current V I - VO = 5V 5.5 7 A Termal Regulation T A = 25°C, 30ms pulse 0.003 0.015 %/W SVR Supply Voltage Rejection f = 120 Hz, C O = 25 µF, IO = 5A VI = 6.8 ± 1.5V 60 72 dB eN RMS Output Noise Voltage (% of VO ) TA = 25°C f =10Hz to 10KHz 0.003 % S Temperature Stability 0.5 % S Long Term Stability T A = 125°C 1000Hrs 0.5 % Symbol Parameter Test Conditions Min. Typ. Max. Unit VO Output Voltage I O = 0 mA T J = 25°C 3.564 3.6 3.636 V IO = 0 to 5A VI = 5.2 to 10V 3.528 3.6 3.672 V ΔVO Line Regulation I O = 0 mA V I = 5.2 to 10V TJ = 25°C 0.5 10 mV IO = 0 mA V I = 5.2 to 10V 1 10 mV ΔVO Load Regulation I O = 0 to 5A TJ = 25°C 3 15 mV IO = 0 to 5A 7 20 V Vd Dropout Voltage I O =5 A 1.3 1.5 V Iq Quiescent Current V I ≤ 10V 5 10 mA Isc Short Circuit Current V I - VO = 5V 5.5 7 A Termal Regulation T A = 25°C, 30ms pulse 0.003 0.015 %/W SVR Supply Voltage Rejection f = 120 Hz, C O = 25 µF, IO = 5A VI = 7.1 ± 1.5V 60 72 dB eN RMS Output Noise Voltage (% of VO ) TA = 25°C f =10Hz to 10KHz 0.003 % S Temperature Stability 0.5 % S Long Term Stability T A = 125°C 1000Hrs 0.5 %

ELECTRICAL CHARACTERISTICS OF KD1084A#5 (VI=8V, CI = CO =10µF (Tant.), TA = -40 to 125°C, unless otherwise specified.) ELECTRICAL CHARACTERISTICS OF KD1084A (VI=4.25V, CI = CO =10µF (Tant.), TA = -40 to 125°C, unless otherwise specified.) Symbol Parameter Test Conditions Min. Typ. Max. Unit VO Output Voltage I O = 0 mA T J = 25°C 4.95 5 5.05 V IO = 0 to 5A VI = 6.6 to 10V 4.9 5 5.1 V ΔVO Line Regulation I O = 0 mA V I = 6.6 to 10V TJ = 25°C 0.5 10 mV IO = 0 mA V I = 6.6 to 10V 1 10 mV ΔVO Load Regulation I O = 0 to 5A TJ = 25°C 5 20 mV IO = 0 to 5A 10 35 V Vd Dropout Voltage I O =5 A 1.3 1.5 V Iq Quiescent Current V I ≤ 10V 5 10 mA Isc Short Circuit Current V I - VO = 5V 5.5 7 A Termal Regulation T A = 25°C, 30ms pulse 0.003 0.015 %/W SVR Supply Voltage Rejection f = 120 Hz, C O = 25 µF, IO = 5A VI = 8.5 ± 1.5V 60 72 dB eN RMS Output Noise Voltage (% of VO ) TA = 25°C f =10Hz to 10KHz 0.003 % S Temperature Stability 0.5 % S Long Term Stability T A = 125°C 1000Hrs 0.5 % Symbol Parameter Test Conditions Min. Typ. Max. Unit VO Output Voltage I O = 10mA T J = 25°C 1.237 1.25 1.263 V IO = 10mA to 5A V I = 2.85 to 10V 1.225 1.25 1.275 V ΔVO Line Regulation I O = 10mA V I = 2.85 to 10V TJ = 25°C 0.015 0.2 % IO = 10mA V I = 2.85 to 10V 0.035 0.2 % ΔVO Load Regulation I O = 10mA to 5A T J = 25°C 0.1 0.3 % IO = 10mA to 5A 0.2 0.4 % Vd Dropout Voltage I O = 5A 1.3 1.5 V IO(min) Minimum Load Current V I = 10V 3 10 mA Isc Short Circuit Current V I - VO = 5V 5.5 7 A Termal Regulation T A = 25°C, 30ms pulse 0.003 0.015 %/W SVR Supply Voltage Rejection f = 120 Hz, C O = 25 µF, CADJ = 25 µF, IO = 5A V I = 4.75 ± 1.5V 60 72 dB IADJ Adjust Pin Current V I = 4.25V I O = 10 mA 55 120 µA ΔIADJ Adjust Pin Current Change IO = 10mA to 5A V I = 2.85 to 10V 0.2 5 µA eN RMS Output Noise Voltage (% of VO ) TA = 25°C f =10Hz to 10KHz 0.003 % S Temperature Stability 0.5 % S Long Term Stability T A = 125°C 1000Hrs 0.5 %

ELECTRICAL CHARACTERISTICS OF KD1084#15 (VI=4.5V, CI = CO =10µF (Tant.), TA = -40 to 125°C, unless otherwise specified.) ELECTRICAL CHARACTERISTICS OF KD1084#18 (VI=4.8V, CI = CO =10µF (Tant.), TA = -40 to 125°C, unless otherwise specified.) Symbol Parameter Test Conditions Min. Typ. Max. Unit VO Output Voltage I O = 0 mA T J = 25°C 1.47 1.5 1.536 V IO = 0 to 5A VI = 3.1 to 10V 1.455 1.5 1.545 V ΔVO Line Regulation I O = 0 mA V I = 3.1 to 10V TJ = 25°C 0.5 6 mV IO = 0 mA V I = 3.1 to 10V 1 6 mV ΔVO Load Regulation I O = 0 to 5A TJ = 25°C 3 15 mV IO = 0 to 5A 7 20 V Vd Dropout Voltage I O =5 A 1.3 1.5 V Iq Quiescent Current V I ≤ 10V 5 10 mA Isc Short Circuit Current V I - VO = 5V 5.5 7 A Termal Regulation T A = 25°C, 30ms pulse 0.003 0.015 %/W SVR Supply Voltage Rejection f = 120 Hz, C O = 25 µF, IO = 5A VI = 5 ± 1.5V 60 75 dB eN RMS Output Noise Voltage (% of VO ) TA = 25°C f =10Hz to 10KHz 0.003 % S Temperature Stability 0.5 % S Long Term Stability T A = 125°C 1000Hrs 0.5 % Symbol Parameter Test Conditions Min. Typ. Max. Unit VO Output Voltage I O = 0 mA T J = 25°C 1.764 1.8 1.836 V IO = 0 to 5A VI = 3.4 to 10V 1.746 1.8 1.854 V ΔVO Line Regulation I O = 0 mA V I = 3.4 to 10V TJ = 25°C 0.5 6 mV IO = 0 mA V I = 3.4 to 10V 1 6 mV ΔVO Load Regulation I O = 0 to 5A TJ = 25°C 3 15 mV IO = 0 to 5A 7 20 V Vd Dropout Voltage I O =5 A 1.3 1.5 V Iq Quiescent Current V I ≤ 10V 5 10 mA Isc Short Circuit Current V I - VO = 5V 5.5 7 A Termal Regulation T A = 25°C, 30ms pulse 0.003 0.015 %/W SVR Supply Voltage Rejection f = 120 Hz, C O = 25 µF, IO = 5A VI = 5.3 ± 1.5V 60 75 dB eN RMS Output Noise Voltage (% of VO ) TA = 25°C f =10Hz to 10KHz 0.003 % S Temperature Stability 0.5 % S Long Term Stability T A = 125°C 1000Hrs 0.5 %

ELECTRICAL CHARACTERISTICS OF KD1084#25 (VI=5.5V, CI = CO =10µF (Tant.), TA = -40 to 125°C, unless otherwise specified.) ELECTRICAL CHARACTERISTICS OF KD1084#285 (VI=5.85V, CI = CO =10µF (Tant.), TA = -40 to 125°C, unless otherwise specified.) Symbol Parameter Test Conditions Min. Typ. Max. Unit VO Output Voltage I O = 0 mA T J = 25°C 2.45 2.5 2.55 V IO = 0 to 5A VI = 4.1 to 10V 2.425 2.5 2.575 V ΔVO Line Regulation I O = 0 mA V I = 4.1 to 10V TJ = 25°C 0.5 6 mV IO = 0 mA V I = 4.1 to 10V 1 6 mV ΔVO Load Regulation I O = 0 to 5A TJ = 25°C 3 15 mV IO = 0 to 5A 7 20 V Vd Dropout Voltage I O =5 A 1.3 1.5 V Iq Quiescent Current V I ≤ 10V 5 10 mA Isc Short Circuit Current V I - VO = 5V 5.5 7 A Termal Regulation T A = 25°C, 30ms pulse 0.003 0.015 %/W SVR Supply Voltage Rejection f = 120 Hz, C O = 25 µF, IO = 5A VI = 6 ± 1.5V 60 72 dB eN RMS Output Noise Voltage (% of VO ) TA = 25°C f =10Hz to 10KHz 0.003 % S Temperature Stability 0.5 % S Long Term Stability T A = 125°C 1000Hrs 0.5 % Symbol Parameter Test Conditions Min. Typ. Max. Unit VO Output Voltage I O = 0 mA T J = 25°C 2.793 2.85 2.907 V IO = 0 to 5A VI = 4.5 to 10V 2.765 2.85 2.935 V ΔVO Line Regulation I O = 0 mA V I = 4.5 to 10V TJ = 25°C 0.5 6 mV IO = 0 mA V I = 4.5 to 10V 1 6 mV ΔVO Load Regulation I O = 0 to 5A TJ = 25°C 3 15 mV IO = 0 to 5A 7 20 V Vd Dropout Voltage I O =5 A 1.3 1.5 V Iq Quiescent Current V I ≤ 10V 5 10 mA Isc Short Circuit Current V I - VO = 5V 5.5 7 A Termal Regulation T A = 25°C, 30ms pulse 0.003 0.015 %/W SVR Supply Voltage Rejection f = 120 Hz, C O = 25 µF, IO = 5A VI = 6.35 ± 1.5V 60 72 dB eN RMS Output Noise Voltage (% of VO ) TA = 25°C f =10Hz to 10KHz 0.003 % S Temperature Stability 0.5 % S Long Term Stability T A = 125°C 1000Hrs 0.5 %

ELECTRICAL CHARACTERISTICS OF KD1084#33 (VI=6.3V, CI = CO =10µF (Tant.), TA = -40 to 125°C, unless otherwise specified.) ELECTRICAL CHARACTERISTICS OF KD1084#36 (VI=6.6V, CI = CO =10µF (Tant.), TA = -40 to 125°C, unless otherwise specified.) Symbol Parameter Test Conditions Min. Typ. Max. Unit VO Output Voltage I O = 0 mA T J = 25°C 3.234 3.3 3.366 V IO = 0 to 5A VI = 4.9 to 10V 3.2 3.3 3.4 V ΔVO Line Regulation I O = 0 mA V I = 4.9 to 10V TJ = 25°C 0.5 6 mV IO = 0 mA V I = 4.9 to 10V 1 6 mV ΔVO Load Regulation I O = 0 to 5A TJ = 25°C 3 15 mV IO = 0 to 5A 7 20 V Vd Dropout Voltage I O =5 A 1.3 1.5 V Iq Quiescent Current V I ≤ 10V 5 10 mA Isc Short Circuit Current V I - VO = 5V 5.5 7 A Termal Regulation T A = 25°C, 30ms pulse 0.003 0.015 %/W SVR Supply Voltage Rejection f = 120 Hz, C O = 25 µF, IO = 5A VI = 6.8 ± 1.5V 60 72 dB eN RMS Output Noise Voltage (% of VO ) TA = 25°C f =10Hz to 10KHz 0.003 % S Temperature Stability 0.5 % S Long Term Stability T A = 125°C 1000Hrs 0.5 % Symbol Parameter Test Conditions Min. Typ. Max. Unit VO Output Voltage I O = 0 mA T J = 25°C 3.528 3.6 3.672 V IO = 0 to 5A VI = 5.2 to 10V 3.492 3.6 3.708 V ΔVO Line Regulation I O = 0 mA V I = 5.2 to 10V TJ = 25°C 0.5 10 mV IO = 0 mA V I = 5.2 to 10V 1 10 mV ΔVO Load Regulation I O = 0 to 5A TJ = 25°C 3 15 mV IO = 0 to 5A 7 20 V Vd Dropout Voltage I O =5 A 1.3 1.5 V Iq Quiescent Current V I ≤ 10V 5 10 mA Isc Short Circuit Current V I - VO = 5V 5.5 7 A Termal Regulation T A = 25°C, 30ms pulse 0.003 0.015 %/W SVR Supply Voltage Rejection f = 120 Hz, C O = 25 µF, IO = 5A VI = 7.1 ± 1.5V 60 72 dB eN RMS Output Noise Voltage (% of VO ) TA = 25°C f =10Hz to 10KHz 0.003 % S Temperature Stability 0.5 % S Long Term Stability T A = 125°C 1000Hrs 0.5 %

ELECTRICAL CHARACTERISTICS OF KD1084#5 (VI=8V, CI = CO =10µF (Tant.), TA = -40 to 125°C, unless otherwise specified.) ELECTRICAL CHARACTERISTICS OF KD1084 (VI=4.25V, CI = CO =10µF (Tant.), TA = -40 to 125°C, unless otherwise specified.) Symbol Parameter Test Conditions Min. Typ. Max. Unit VO Output Voltage I O = 0 mA T J = 25°C 4.9 5 5.1 V IO = 0 to 5A VI = 6.6 to 10V 4.85 5 5.15 V ΔVO Line Regulation I O = 0 mA V I = 6.6 to 10V TJ = 25°C 0.5 10 mV IO = 0 mA V I = 6.6 to 10V 1 10 mV ΔVO Load Regulation I O = 0 to 5A TJ = 25°C 5 20 mV IO = 0 to 5A 10 35 V Vd Dropout Voltage I O =5 A 1.3 1.5 V Iq Quiescent Current V I ≤ 10V 5 10 mA Isc Short Circuit Current V I - VO = 5V 5.5 7 A Termal Regulation T A = 25°C, 30ms pulse 0.003 0.015 %/W SVR Supply Voltage Rejection f = 120 Hz, C O = 25 µF, IO = 5A VI = 8.5 ± 1.5V 60 72 dB eN RMS Output Noise Voltage (% of VO ) TA = 25°C f =10Hz to 10KHz 0.003 % S Temperature Stability 0.5 % S Long Term Stability T A = 125°C 1000Hrs 0.5 % Symbol Parameter Test Conditions Min. Typ. Max. Unit VO Output Voltage I O = 10mA T J = 25°C 1.225 1.25 1.275 V IO = 10mA to 5A V I = 2.85 to 10V 1.213 1.25 1.287 V ΔVO Line Regulation I O = 10mA V I = 2.85 to 10V TJ = 25°C 0.015 0.2 % IO = 10mA V I = 2.85 to 10V 0.035 0.2 % ΔVO Load Regulation I O = 10mA to 5A T J = 25°C 1 0.3 % IO = 10mA to 5A 0.2 0.4 % Vd Dropout Voltage I O = 5A 1.3 1.5 V IO(min) Minimum Load Current V I = 10V 3 10 mA Isc Short Circuit Current V I - VO = 5V 5.5 7 A Termal Regulation T A = 25°C, 30ms pulse 0.003 0.015 %/W SVR Supply Voltage Rejection f = 120 Hz, C O = 25 µF, CADJ = 25 µF, IO = 5A V I = 4.75 ± 1.5V 60 72 dB IADJ Adjust Pin Current V I = 4.25V I O = 10 mA 55 120 µA ΔIADJ Adjust Pin Current Change IO = 10mA to 5A V I = 2.85 to 10V 0.2 5 µA eN RMS Output Noise Voltage (% of VO ) TA = 25°C f =10Hz to 10KHz 0.003 % S Temperature Stability 0.5 % S Long Term Stability T A = 125°C 1000Hrs 0.5 %

DIM. mm. inch A 4.40 4.60 0.173 0.181 C 1.23 1.32 0.048 0.051 D 2.40 2.72 0.094 0.107 D1 1.27 0.050 E 0.49 0.70 0.019 0.027 F 0.61 0.88 0.024 0.034 F1 1.14 1.70 0.044 0.067 F2 1.14 1.70 0.044 0.067 G 4.95 5.15 0.194 0.203 G1 2.4 2.7 0.094 0.106 H2 10.0 10.40 0.393 0.409 L2 16.4 0.645 L4 13.0 14.0 0.511 0.551 L5 2.65 2.95 0.104 0.116 L6 15.25 15.75 0.600 0.620 L7 6.2 6.6 0.244 0.260 L9 3.5 3.93 0.137 0.154 TO-220 MECHANICAL DAT A P011C

DIM. mm. inch A 4.4 4.6 0.173 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.7 0.93 0.027 0.036 B2 1.14 1.7 0.044 0.067 C 0.45 0.6 0.017 0.023 C2 1.23 1.36 0.048 0.053 D 8.95 9.35 0.352 0.368 D1 8 0.315 E 10 10.4 0.393 0.409 E1 8.5 0.335 G 4.88 5.28 0.192 0.208 L 15 15.85 0.590 0.624 L2 1.27 1.4 0.050 0.055 L3 1.4 1.75 0.055 0.068 M 2.4 3.2 0.094 0.126 R 0.4 0.016 V2 0˚ 8˚ 0˚ 8˚ D 2PAK MEC HANICAL DATA P011P6G

DIM. mm. inch A 4.40 4.60 0.173 0.181 A1 2.49 2.69 0.098 0.106 B 0.7 0.93 0.027 0.036 B2 1.14 1.7 0.044 0.067 C 0.45 0.60 0.017 0.023 C2 1.21 1.36 0.047 0.053 D 8.95 9.35 0.352 0.368 E 10 10.4 0.393 0.409 G 4.88 5.28 0.192 0.208 L 15 15.85 0.590 0.106 L2 1.27 1.4 0.050 0.055 D 2PAK/A MECHA NICAL DATA

DIM. mm. inch A 2.2 2.4 0.086 0.094 A1 0.9 1.1 0.035 0.043 A2 0.03 0.23 0.001 0.009 B 0.64 0.9 0.025 0.035 B2 5.2 5.4 0.204 0.212 C 0.45 0.6 0.017 0.023 C2 0.48 0.6 0.019 0.023 D 6 6.2 0.236 0.244 E 6.4 6.6 0.252 0.260 G 4.4 4.6 0.173 0.181 H 9.35 10.1 0.368 0.397 L2 0.8 0.031 L4 0.6 1 0.023 0.039 DPAK MECHANI CAL DATA 0068772-B

Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2002 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. © http://www.st.com