KB264X82X7

KB2 FRANCEJOINT | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 5

Technical content

|| SEAL DESIGN Tolerance for the outside diameter of the seal (ØD) Bore diameter ØD1 (mm) Apparent metal cage Rubber coating Coating with grooves Roundness tolerance Bore diameter ØD1 (mm) Apparent metal cage Rubber coating ØD1 ≤ 50.0 0.18 0.25 50.0 < ØD1 ≤ 80.0 0.25 0.35 80.0 < ØD1 ≤ 120.0 0.30 0.50 120.0 < ØD1 ≤ 180.0 0.40 0.65 180.0 < ØD1 ≤ 300.0 0.25% of the outside diameter 0.80 300.0 < ØD1 ≤ 500.0 0.25% of the outside diameter 1.00 Tolerance for the inside diameter of the seal (Ød) Free and without constraint, the inside diameter of the sealing lip is always smaller than the diameter of the shaft. The pre-tightening or interference denotes the difference between these two values. Depending on the shaft diameter, the diameter of the sealing lip is generally considered to be less, between 0.8 and 3.5 mm. |DESCRIPTION The KB2 profile is a shaft seal composed of a single external metal cage, a primary sealing lip without a spring and an additional anti-pollution lip. |ADVANTAGES Good radial rigidity, particularly for large diameters Good stability when assembled, preventing the bounce-back effect Sealing for high viscosity fluids Primary sealing lip generating low levels of friction and heat Protection against undesirable air contaminants |APPLICATIONS All types of rotative applications Machine tools Agriculture Construction Transmission Gear boxes Motors Pumps |MATERIALS Rubber ACM 70 - 75 Shore A EPDM 70 - 75 Shore A FKM 70 - 75 Shore A HNBR 70 - 75 Shore A NBR 70 - 75 Shore A Metal cage Steel - AISI 1010 Stainless steel - AISI 304 Stainless steel - AISI 316 STANDARD SHAFT SEALS KB2 ROTARY SEALS | STANDARD SHAFT SEALS | KB2 QUALITY & EXPERTISE FOR YOUR SEALING NEEDS

Maximum temperature depending on the materials ACM AEM EPDM FKM HNBR NBR VMQ Mineral oils Oils for motors +130°C +130°C – +170°C +130°C +100°C +150°C Oils for gearboxes +120°C +130°C – +150°C +110°C +80°C +130°C Oils for hypoid gears +120°C +130°C – +150°C +110°C +80°C – ATF oils +120°C +130°C – +170°C +130°C +100°C – Hydraulic oils +120°C +130°C – +150°C +130°C +90°C – Greases – +130°C – – +100°C +90°C – Fire-resistant fluids HFA group - Emulsion with more than 80% water – – – – +70°C +70°C +60°C HFB group - Opposite solution (water in oil) – – – – +70°C +70°C +60°C HFC group - Polymer aqueous solution – – +60°C – +70°C +70°C – HFD group - Water-free synthetic fluids – – – +150°C – – – Other fluids EL + L heating oil – – – – +100°C +90°C – Water for washing – – +130°C +100°C +100°C +90°C – Temperature range || TECHNICAL DATA Speed 50 100 150 200 Shaft diameter (mm) Peripheral shaft speed (m/s) Linear speed calculation: s (m/s) = [shaft Ø (mm) x speed (rpm) x π] 60,000 Pressure Standard shaft seals with a primary sealing lip and no spring are used only in pressurised environments. We recommend using shaft seals with springs for use in pressurised environments between 0.02 and 0.05 MPa (max). ROTARY SEALS | STANDARD SHAFT SEALS | KB2 www.francejoint.com

10° / 20° R2 max 20° / 30° Ø D1 H8 Ø d1 h11 Ø d3 R || SHAFT DESIGN Shaft hardness Rotation speed Hardness in HRC s ≤ 4.0 m/sec 45 HRC 4.0 < s ≤ 10.0 m/s 55 HRC s > 10.0 m/sec 60 HRC Surface roughness Ra 0.2 to 0.8 µm Rz 1.0 to 4.0 µm Rmax ≤6.3 µm Shaft tolerance Shaft diameter Ød1 (mm) Tolerance h11 (mm) Ød1 ≤ 3.0 -0.060 / 0 10.0 < Ød1 ≤ 18.0 -0.110 / 0 18.0 < Ød1 ≤ 30.0 -0.130 / 0 30.0 < Ød1 ≤ 50.0 -0.160 / 0 50.0 < Ød1 ≤ 80.0 -0.190 / 0 80.0 < Ød1 ≤ 120.0 -0.220 / 0 120.0 < Ød1 ≤ 180.0 -0.250 / 0 180.0 < Ød1 ≤ 250.0 -0.290 / 0 250.0 < Ød1 ≤ 315.0 -0.320 / 0 315.0 < Ød1 ≤ 400.0 -0.360 / 0 400.0 < Ød1 ≤ 500.0 -0.400 / 0 Chamfer and radius Shaft diameter Ød1 (mm) Chamfer diameter Ød3 (mm) Radius R (mm) Ød1 ≤ 10.0 Ød1 - 1.50 2.00 10.0 < Ød1 ≤ 20.0 Ød1 - 2.00 2.00 20.0 < Ød1 ≤ 30.0 Ød1 - 2.50 3.00 30.0 < Ød1 ≤ 40.0 Ød1 - 3.00 3.00 40.0 < Ød1 ≤ 50.0 Ød1 - 3.50 4.00 50.0 < Ød1 ≤ 70.0 Ød1 - 4.00 4.00 70.0 < Ød1 ≤ 95.0 Ød1 - 4.50 5.00 95.0 < Ød1 ≤ 130.0 Ød1 - 5.50 6.00 130.0 < Ød1 ≤ 240.0 Ød1 - 7.00 8.00 240.0 < Ød1 ≤ 500.0 Ød1 - 11.00 12.00 Shaft run out and eccentricity 3000 r.p.m 2000 r.p.m 1000 r.p.m 500 r.p.m 0 50 100 150 200 0,1 0,2 0,3 0,4 Shaft diameter (mm) Shaft run-out + eccentricity (mm) ROTARY SEALS | STANDARD SHAFT SEALS | KB2 www.francejoint.com

Ra 0.8 to 3.2 µm Rz 6.3 to 16.0 µm Rmax ≤16.0 µm Housing tolerance Bore diameter ØD1 (mm) Tolerance H8 (mm) 10.0 < ØD1 ≤ 18.0 0 / +0.027 18.0 < ØD1 ≤ 30.0 0 / +0.033 30.0 < ØD1 ≤ 50.0 0 / +0.039 50.0 < ØD1 ≤ 80.0 0 / +0.046 80.0 < ØD1 ≤ 120.0 0 / +0.054 120.0 < ØD1 ≤ 180.0 0 / +0.063 180.0 < ØD1 ≤ 250.0 0 / +0.072 250.0 < ØD1 ≤ 315.0 0 / +0.081 315.0 < ØD1 ≤ 400.0 0 / +0.089 400.0 < ØD1 ≤ 500.0 0 / +0.097 500.0 < ØD1 ≤ 630.0 0 / +0.110 Housing radius and width Height H1 (mm) Width Radius R2 max (mm)L2min (H1 x 0.85) L1min (H1 x +0.3) 7.00 5.95 7.30 0.508.00 6.80 8.30 10.00 8.50 10.30 12.00 10.30 12.30 0.7015.00 12.75 15.30 20.00 17.00 20.30 || HOUSING DESIGN 10° / 20° R2 max 20° / 30° Ø D1 H8 Ø d1 h11 Ø d3 R ROTARY SEALS | STANDARD SHAFT SEALS | KB2 www.francejoint.com

|| DIMENSIONS Part number Shaft diameter Ød1 h11 Bore diameter ØD1 H8 Seal height KB2 16 x 30 x 8 16.00 30.00 8.00 KB2 32 x 52 x 9.5 32.00 52.00 9.50 KB2 38 x 52 x 6 38.00 52.00 6.00 KB2 39 x 54 x 6 39.00 54.00 6.00 KB2 40 x 55 x 6.5 40.00 55.00 6.50 Part number Shaft diameter Ød1 h11 Bore diameter ØD1 H8 Seal height KB2 40 x 55 x 8 40.00 55.00 8.00 KB2 45 x 62 x 6 45.00 62.00 6.00 KB2 46 x 62 x 7 46.00 62.00 7.00 KB2 64 x 82 x 7 64.00 82.00 7.00 KB2 80 x 115 x 6 80.00 115.00 6.00 ROTARY SEALS | STANDARD SHAFT SEALS | KB2 FRANCE JOINT SAS Zone Artisanale Le Mortier - B.P . 50009 - Cugand - 85613 Montaigu Cedex - France Ph. +33 (0)2 51 42 13 76 - Fax +33 (0)2 51 43 61 14 - Email: contact@francejoint.fr - Website: www.francejoint.com