K70_V04 BANNER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

Compact, Single-Point Devices for Error-Proofing of Bin-Picking Operations

  • Excellent immunity to false triggering by water spray, detergents, oils, and other foreign materials
  • Rugged, cost-effective and easy-to-install solutions for error-proofing and parts- verification applications
  • Compact devices are completely self contained—No controller needed
  • Illuminated dome provides an easy-to-see green job light: some models also light red for alternate operation
  • Easy actuation—no force required
  • 12 V to 30 V dc operation
  • Can be actuated with bare hands or in gloves WARNING: Not To Be Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Models Model1 Function Output2 Connection Indicators Job Mis-Pick Sense K70APT2GRYC3Q • Job light always on with job input until touched
  • Touch activates output and overrides job light with sense light
  • Touch with inactive job input activates mis- pick light and activates output PNP, N.O. Integral 5-pin M12/Euro-style male quick disconnect (QD) Green Red Yellow K70RPT2GRYC3Q PNP, N.C. K70APT2GRYC4Q • Job light always on with job input until touched
  • Touch activates output and overrides job light with sense light until job input is removed
  • Touch with inactive job input activates mis- pick light for 5 seconds after touched and activates output PNP, N.O. Green Red Yellow K70RPT2GRYC4Q PNP, N.C. Indicator and Output Behavior NOTE: "C3" and "C4" models as referenced in the table pertain to a part of the product model number, immediately preceding the designation. Sensor Conditions Output Signal StatusC3 Models C4 Models Job input active Hand/pick absent On Green On Green Off 1 Integral 5-pin M12/Euro-style quick disconnect models are listed.
  • To order the 2 m (6.5 ft) PVC cable model, omit the suffix "Q" in the model number. For example, K70APT2GRYC3.
  • To order the 150 mm (6 in) Euro-style PUR cable quick disconnect model, replace the suffix "Q" with "QPMA" in the model number. For example, K70APT2GRYC3QPMA.
  • To order the 150 mm (6 in) PVC cable model with a 5-pin M12/Euro-style PVC connector, replace the suffix "Q" with "QP" in the model number. For example, K70APT2GRYC3QP.
  • Models with a quick disconnect require a mating cordset. 2 PNP models only are listed. For other output types, contact Banner Engineering. EZ-LIGHT® Touch K70 Specialty Pick-to- Light Original Document 189842 Rev. C

22 July 2016

Sensor Conditions Output Signal StatusC3 Models C4 Models Hand/pick present On Yellow On Yellow until job input is removed On No job input Hand/pick absent Off Off Off Hand/pick present On Red On Red for 5 seconds after hand/pick is removed On Specifications Supply Voltage

12 V to 30 V dc

< 220 mA maximum current at 12 V dc (exclusive of load) < 110 mA maximum current at 30 V dc (exclusive of load) Supply Protection Circuitry Protected against reverse polarity and transient voltages Output Rating Maximum load: 150 mA ON-State saturation voltage: < 2 V dc at 10 mA ; < 2.5 V dc at 150 mA OFF-State leakage current: < 10 µA at 30 V dc Output Response Time 50 ms ON; 500 ms leading edge OFF Power-Up Delay 300 ms Mounting M30 × 1.5 threaded base; maximum torque 4.5 N·m (40 in·lbf) Indicators Job pick indicator: Green Mis-pick indicator: Red Sense indicator: Yellow Indicator Lumens Color Typical Wavelength Typical Intensity (lm) Green 525 nm 45 Red 625 nm 26 Yellow 590 nm 13 Operating Conditions 90% at +50 °C maximum relative humidity (non-condensing) Storage Environmental Rating IEC IP65 Construction Housing and dome: Polycarbonate Mounting nut: PBT Connections Integral 5-pin M12/Euro-style male quick disconnect (QD); 2 m (6.5 ft) unterminated PVC-jacketed cable; 150 mm (6 in) PVC cable with a 5- pin M12/Euro-style male quick disconnect (QD); or 150 mm (6 in) PUR cable with a 5-pin M12/Euro-style male quick disconnect (QD) Vibration and Mechanical Shock Vibration 10 Hz to 55 Hz 1.0 mm p-p amplitude per IEC 60068-2-6 Shock 30G 11 ms duration, half sine wave per IEC 60068-2-27 Certifications Required Overcurrent Protection WARNING: Electrical connections must be made by qualified personnel in accordance with local and national electrical codes and regulations. Overcurrent protection is required to be provided by end product application per the supplied table. Overcurrent protection may be provided with external fusing or via Current Limiting, Class 2 Power Supply. Supply wiring leads < 24 AWG shall not be spliced. For additional product support, go to http:// www.bannerengineering.com. Supply Wiring (AWG) Required Overcurrent Protection (Amps) 20 5.0 22 3.0 24 2.0 26 1.0 28 0.8 30 0.5 EZ-LIGHT® Touch K70 Specialty Pick-to-Light 2 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 189842 Rev. C

49.7[1.96] 20.9[.82] 24.9[.98] 8.0[.32] R31.8[1.25] M30 x 1.5-6g M12 x 1-6g All measurements are listed in millimeters [inches], unless noted otherwise. Wiring Diagram NPN (Sinking) Output Models 12-30V dc

4 Load

Job Light Enable, Input Low <1.0V Not Used PNP (Sourcing) Output Models 12-30V dc Job Light Enable, Input High >7V Not Used Load Wiring Key 1 = Brown 2 = White 3 = Blue 4 = Black 5 = Gray NOTE: Cabled wiring diagrams are shown.Quick disconnect (QD) wiring diagrams are functionally identical. Accessories Cordsets 5-Pin Threaded M12/Euro-Style Cordsets—Single Ended Model Length Style Dimensions Pinout (Female) MQDC1-501.5 0.50 m (1.5 ft) Straight 44 Typ. ø 14.5 M12 x 1 1 = Brown 2 = White 3 = Blue 4 = Black 5 = Gray MQDC1-506 1.83 m (6 ft) MQDC1-515 4.57 m (15 ft) MQDC1-530 9.14 m (30 ft) EZ-LIGHT® Touch K70 Specialty Pick-to-Light P/N 189842 Rev. C www.bannerengineering.com - Tel: +1-763-544-3164 3

5-Pin Threaded M12/Euro-Style Cordsets—Single Ended Model Length Style Dimensions Pinout (Female) MQDC1-506RA 1.83 m (6 ft) Right-Angle 32 Typ.[1.26"] 30 Typ.[1.18"] ø 14.5 [0.57"] M12 x 1 MQDC1-515RA 4.57 m (15 ft) MQDC1-530RA 9.14 m (30 ft) Brackets SMB30A

  • Right-angle bracket with curved slot for versatile orientation
  • Clearance for M6 (¼ in) hardware
  • Mounting hole for 30 mm sensor
  • 12-ga. stainless steel 69 AB C Hole center spacing: A to B=40 Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5 SSA-MBK-EEC1
  • Single 30 mm hole
  • 8 gauge steel, black finish (powder coat)
  • Front surface for customer applied labels 85 6045 B A Hole size: A = ø 7 , B = ø 30 SMB30FVK
  • V-clamp, flat bracket and fasteners for mounting to pipe or extensions
  • Clamp accommodates 28 mm dia. tubing or 1 in. square extrusions
  • 30 mm hole for mounting sensors 46 118 A Hole size: A= ø 31 SMB30MM
  • 12-ga. stainless steel bracket with curved mounting slots for versatile orientation
  • Clearance for M6 (¼ in) hardware
  • Mounting hole for 30 mm sensor A BC Hole center spacing: A = 51, A to B = 25.4 Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1 SMB30RAVK
  • V-clamp, right-angle bracket and fasteners for mounting sensors to pipe or extrusion
  • Clamp accommodates 28 mm dia. tubing or 1 in. square extrusions
  • 30 mm hole for mounting sensors A Hole size: A = ø 30.5 SMBAMS30P
  • Flat SMBAMS series bracket
  • 30 mm hole for mounting sensors
  • Articulation slots for 90°+ rotation
  • 12-ga. 300 series stainless steel 93 A C B Hole center spacing: A=26.0, A to B=13.0 Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0 EZ-LIGHT® Touch K70 Specialty Pick-to-Light 4 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 189842 Rev. C

Banner Engineering Corp. Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Copyright Notice Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any EZ-LIGHT® Touch K70 Specialty Pick-to-Light www.bannerengineering.com - Tel: +1-763-544-3164