K2201G

K2201G LITTELFUSE | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

Features

Electrical Specifications Symbol Parameters Test Conditions Min Max Unit VBO Breakover/Trigger Voltage K2201G K2401G K2501G K3601G 200 220 240 340 230 250 280 380 V V DRM Repetitive Peak Off-State Voltage K2201G K2401G K2501G K3601G 180 190 200 270 V I T(RMS) On-State RMS Current, TJ < 125ºC 50/60Hz Sine Wave 1 A IH Dynamic Holding Current, R=100 8 50/60Hz Sine Wave 160 TYP mA RS (IS – IBO) 50/60Hz Sine Wave 100 8 tCOMM Commutation Time TJ < 125ºC See test circuit and waveform in Figure 9 100 μsec IBO Breakover Current 50/60Hz Sine Wave 10 uA ITSM Non-repetitive 1 cycle On-State peak value 60Hz 50Hz 20.0 16.7 A di/dt Critical Rate of Rise of On-State Current 150 A/μsec dv/dt Critical Rate of Rise of Off-State Voltage 1500 V/μsec TS Storage Temperature Range -40 +125 °C TJ Max Operating Junction Temperature -40 +125 °C RRJL Thermal Resistance Junction to lead 18 °C/W Schematic Symbol t"$DJSDVJUPSJFOUFE t5SJHHFSJOH7PMUBHFPG to 380V t$PNQMJBOU

Applications

Typical application circuit presented in Figure 10 of this data sheet (Typical Metal Halide Ignitor Circuit).

Revised: August 29, 2008 ©2008 Littelfuse, Inc. T eccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Multipulse™ SIDACs Kxxx1G Series Soldering Parameters Reflow Condition Pb – Free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C Note: With proper component selection, this circuit will produce three pulses for ignition of metal halide lamp that requires a minimum of three pulses at 4kV magnitude and >1uSec duration each at a minimum repetition rate of 3.3kHz. Ballast Kxxx1G

220 V / 240 V

H.V. Step-up Transformer 0.1-0.15 μF 0.22-0.33μF 5-6μH 5.6K-8.2K Figure 10: T ypical Metal Halide Ignitor Circuit Time Temperature TP TL TS(max) TS(min) tP tL tS time to peak temperature PreheatPreheat Ramp-upRamp-up Ramp-downRamp-do

335©2008 Littelfuse, Inc. Revised: August 29, 2008 T eccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 335©2008 Littelfuse, Inc. T eccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Kxxx1G Series Multipulse™ SIDACs MultipulseTM SIDACs L LG D B Physical Specifications Reliability/Environmental T ests Test Specifications and Conditions High T emperature Voltage Blocking MIL -STD-750: Method 1040, Condition A Rated VDRM (VAC-peak), 125°C, 1008 hours T emperature Cycling MIL -STD-750: Method 1051, 100 cycles; -40°C to 150°C, 15-minute dwell time T emperature / Humidity EIA/JEDEC: JESD22-A101 1008 hours; 160V - DC: 85°C; 85% relative humidity High T emp Storage MIL -STD-750: Method 1031 150°C, 1008 hours Low-T emp Storage -40°C, 1008 hours Thermal Shock MIL -STD-750: Method 1056 10 cycles; 0°C to 100°C; 5-minute dwell- time at each temperature; 10-sec (max) transfer time between temperature Autoclave EIA/JEDEC: JESD22-A102 168 hours (121°C at 2 ATMs) and 100% RH Resistance to Solder Heat MIL -STD-750: Method 2031 260°C, 10 seconds Solderability ANSI/J-STD-002: Category 3, Test A Repetitive Surge Life T esting Multi firings per half cycle at 60Hz in application circuit for 168 hours minimum T erminal Finish 100% Matte Tin Plated Body Material UL recognized epoxy meeting flammability classification 94V-0 Lead Material Copper Alloy Design Considerations Careful selection of the correct device for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Overheating and surge currents are the main killers of SIDACs. Correct mounting, soldering, and forming of the leads also help protect against component damage. Dimensions — DO-15 (G Package) Dimension Inches Millimeters Max Max Min Max B 0.028 0.034 0.711 0.864 D 0.120 0.140 3.048 3.556 G 0.235 0.270 5.969 6.858 L 1 .000 25.400 Package Weight / unit (mg) DO-15 385 Product Selector Part Number Switching Voltage Range Blocking Voltage Packages VBO Minimum V BO Maximum V DRM K2201G 200V 230V 180V DO-15 K2401G 220V 250V 190V DO-15 K2501G 240V 280V 200V DO-15 K3601G 340V 380V 270V DO-15

Revised: August 29, 2008 ©2008 Littelfuse, Inc. T eccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Multipulse™ SIDACs Kxxx1G Series Part Numbering System Part Marking System K 220 1 G RP SERIES K: Sidac VOLTAGE 220: 200 to 230V 240: 220 to 250V 250: 240 to 280V 360: 340 to 380V CIRCUIT FUNCTION 1: Multipulse™ DEVICE PACKAGE G: DO-15 PACKAGING OPTIONS Blank: Bulk RP: Tape and Reel DO-15 Embossed Carrier RP Specifications 3.15 (80.0) TYP DO-15 Dimensions are in inches (and millimeters). Direction of Feed0.252 (6.4) 0.898 (22.8) 0.197 (5.0) 2.063 (52.4) 10.0 - 14.0 (254.0 - 356.0) Meets all EIA RS-29-6 Standards Packing Options Part Number Package Packing Mode Base Quantity Kxxx1G DO-15 Bulk 1000 Kxxx1GRP Tape & Reel 5000 Note: xxx = voltage