IR05H40CSPTR IRF | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

Features

Ultra Low VF To Footprint Area

  • Very Low Profile (<0.6mm)
  • Low Thermal Resistance
  • Supplied Tested And On Tape & Reel

Applications

Reverse Polarity Protection

  • Current Steering
  • Freewheeling
  • Flyback
  • Oring FlipKYTM FlipKYTM 0.5 Amp

40 Volt

Major Ratings and Characteristics IF(AV) Rectangular waveform 0.5 A VRRM 40 V IFSM @ tp = 5 μs sine 190 A VF @ 0.5 Apk, TJ=125°C 0.42 V TJ range - 55 to 150 °C Characteristics IR05H40CSP Units www.irf.com

Bulletin I0170J rev. D 05/06 www.irf.com TJ Max. Junction Temperature Range (*) - 55 to 150 °C Tstg Max. Storage Temperature Range - 55 to 150 °C RthJLB Typ. Thermal Resistance Junction 35 °C/W DC operation to PCB () RthJA Max. Thermal Resistance Junction 150 °C/W to Ambient () VR Max. DC Reverse Voltage (V) VRWM Max. Working Peak Reverse Voltage (V) 40 Voltage Ratings IF(AV) Max. Average Forward Current 0.5 A 50% duty cycle @ T PCB = 114 °C, rectangular wave form IFSM Max. Peak One Cycle Non-Repetitive 190 A 5 μs Sine or 3μs Rect. pulse Surge Current @ 25°C 10 10ms Sine or 6ms Rect. pulse EAS Non- Repetitive Avalanche Energy 5 mJ T J = 25 °C, IAS = 2.0A, L = 5.0mH IAR Repetitive Avalanche Current 0.5 A Current decaying linearly to zero in 1 μsec Frequency limited by TJ max. Va = 1.5 x Vr typical Parameters Value Units Conditions Absolute Maximum Ratings Following any rated load condition and with rated VRRM applied Part number IR05H40CSPTR Thermal-Mechanical Specifications Parameters Value Units Conditions < thermal runaway condition for a diode on its own heatsink (*) dPtot 1 dTj Rth( j-a) (1) Pulse Width < 300μs, Duty Cycle < 2% VFM Max. Forward Voltage (1) 0.48 0.52 V @ 0.5A T J = 25 °C Drop 0.54 0.58 @ 1A * See Fig. 1 0.38 0.42 @ 0.5A T J = 125 °C 0.46 0.50 @ 1A IRM Max. Reverse Leakage (1) 1 10 μAT J = 25 °C V R = rated VR Current 0.2 0.5 V R = 20V * See Fig. 2 0.08 0.25 V R = 10V 0.05 0.15 V R = 5V 0.5 2 mA T J = 125 °C V R = rated VR 0.2 1 V R = 20V 0.15 0.8 V R = 10V 0.125 0.5 V R = 5V CT Max. Junction Capacitance - 90 pF V R = 5VDC (test signal range 100kHz to 1MHz) 25°C dv/dt Max. Volatge Rate of Charge - 10000 V/ μs (Rated V R) Electrical Specifications Parameters Typ. Max. Units Conditions (**) Mounted on dual sided 0.58 inch square FR4 PCB with 0.2 square inches of 1oz top copper area

Bulletin I0170J rev. D 05/06 www.irf.com Fig. 2 - Typical Values Of Reverse Current Vs. Reverse Voltage (Per Leg) Fig. 3 - Typical Junction Capacitance Vs. Reverse Voltage (Per Leg) Fig. 1 - Max. Forward Voltage Drop Characteristics (Per Leg) Forward Voltage Drop - VFM (V) Instantaneous Forward Current - I F (A) Reverse Voltage - VR (V) Reverse Current - I R (μA) Reverse Voltage - VR (V) Junction Capacitance - C T (p F) 100 1000 0 5 10 15 20 25 30 35 40 T = 25˚CJ 0.1 T = 150˚C T = 125˚C T = 25˚C J J J 0.01 0.1 100 1000 10000 0 5 10 15 20 25 30 35 4 0 125˚C 100˚C 75˚C 50˚C 25˚C Tj = 150˚C

Bulletin I0170J rev. D 05/06 www.irf.com Fig. 6 - Max. Non-Repetitive Surge Current (Per Leg) Fig. 4 - Max. Allowable Case Temperature Vs. Average Forward Current (Per Leg) Fig. 8 - Unclamped Inductive Test Circuit Fig. 5 - Forward Power Loss Characteristics (Per Leg) FREE- WHEEL DIODE 40HF L40S02CU R R E NT MONIT OR HIGH-S PEED S WIT CHIRFP460 L DUT Rg = 25 o h m Vd = 25 Volt+ (2) Formula used: TC = TJ - (Pd + PdREV) x RthJC ; Pd = Forward Power Loss = IF(AV) x VFM @ (IF(AV) / D) (see Fig. 6); PdREV = Inverse Power Loss = VR1 x IR (1 - D); IR @ 80% VR applied Average Forward Current - I F(AV) (A) Allowable Case Temperature (°C) Average Forward Current - IF(AV) (A) Average Power Loss (Watts) Square Wave Pulse Duration - tp (microsec) Non-Repetitive Surge Current - I FSM (A) 100 120 140 160 0 0.2 0.4 0.6 0.8 DC Square wave (D = 0.50) 80% Vr applied see note (2) D = 3/4 D = 1/2 D = 1/3 D = 1/4 D = 1/5 0.1 0.2 0.3 0.4 0 0.2 0.4 0.6 0.8 DC RMS Limit D = 0.20 D = 0.25 D = 0.33 D = 0.50 D = 0.75 100 1000 10 100 1000 10000 At Any Rated Load Condition And With Rated Vrrm Applied Following Surge

Bulletin I0170J rev. D 05/06 www.irf.com 0.300 0.460 0.355 0.395 1.244 0.105 0.125 0.520 Pin 3 Anode 0.450 0.250 0.350 0.700 Pin 2 Cathode 0.350 Pin 1 Cathode RECOMMENDED FOOTPRINT 0.500 0.700 1.244 0.914 3. DIMENSIONS ARE SHOWN IN MILLIMETERS 2. CONTROLLING DIMENSION: MILLIMETER 1. DIMENSIONING & TOLERANCING PER ASME Y14.5M-1994. NOTES: ASSIGNMENTS 3 = ANODE 2 = CATHODE 1 = CATHODE 0.500 2 1 IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 05/06 Data and specifications subject to change without notice. This product has been designed for Consumer Level. Qualification Standards can be found on IR's Web site. FlipKY TM Outline Dimension and Tape and Reel Special Instruction for PCB assembly: see A PPLICATION NOTE AN-1079 LOT NUMBER WORKWEEK (Y, WW) 01 123 LOCATION MARK BALL 1 PART NUMBER E 4mm 1. TAPE AND REEL OUTLINE CONFORMS TO EIA-481 & EIA-541. NOTES: FEED DIRECTION LOCATION A1 BALL 8mm 8mm Ø 13"